ARCADE1UP Ridge Racer Arcade Cabonet HameStop Owner’s Manual

OWNERS MANUAL
AGES 14+

**WARNING**
To ensure the safe operation of the product, be sure to read this Owners Manual before use. Keep this Owners Manual in a safe place for easy reference when needed.

WARNING

READ BEFORE USING THE Arcade1UP SAFETY PRECAUTIONS
The following symbols are used in labels on the game to draw attention to potentially hazardous situations:
WARNING: Failure to avoid the risk may result in death or serious injury
Electrical Shock Hazard. Disconnect power before removing the cover. Should only be done by a qualified technician.
WARNING: To reduce the risk of ore or electric shock, do not expose this apparatus to rain or moisture.

1.  Please read and comprehend all warnings stated in this manual.

2. Do not get the arcade wet when cleaning.

3. Parents and guardians: Please read the entire manual before allowing gamers to play.

4. The AC/DC adapter and apparatus shall not be exposed to dripping or splashing and no object filled with liquids, such as vases, shall be placed on the apparatus.
   The AC/DC adapter is used as a disconnect device.
   The AC/DC adapter of the apparatus should not be obstructed OR should be easily accessed during intended use. To completely disconnect the power input, the AC/DC adapter of the apparatus shall be disconnected from the mains.

5. If the appliance is provided with protective earth terminal, it should be connected to the main outlet with a protective earth connection.

6. Minimum distances are 10 cm / 3.94 inches around the apparatus for sufficient ventilation.

7. The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table cloths, curtains et8. No naked flame sources such as lighted candles should be placed on the apparatus.

8. The apparatus should only be used in moderate climates.

EPILEPSY WARNING
A very small percentage of individuals may experience epileptic seizures or blackouts when exposed to certain light patterns or flashing lights. Exposure to certain patterns or backgrounds on a television screen or when playing video games may trigger epileptic seizures or blackouts in these individuals. To reduce the risk of such a seizure incident, it is recommended to take a 10-15 minute break at each hour of playing.

FCC/ISED STATEMENT
This device complies with part 15 of the FCC rules / Industry Canada’s license-exempt RSS. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC/ISED rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.

WARNING: Arcade1UP assumes no liability for improper installation or excessive loads placed on screws or brackets.
This wall anchor is not a substitute for proper adult supervision.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these Instructions.

2. Keep these Instructions.

3. Heed all Warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong ar provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for a replacement
   obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Unplug this apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in an such as a power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. Use only with a riser specified by the manufacturer, or sold with the apparatus. When a riser is used, use caution when moving the riser/apparatus combination to avoid injury from tip-over.

15. The equipment shall be used at a working ambient temperature 32° – 95°F (0° – 35°C).

16. TIP OVER HAZARD – This apparatus should secure in place by using the provided mounting means. Free standing is capable of resulting in instability causing possible injury. Refer to the installation instruction for detail.

INSTALLATION

This game is designed for indoor and personal use only. It must not be installed outdoors.
The following conditions must be avoided.

1. Direct exposure to sunlight, high humidity, direct water contact, dust, high heat, or extreme cold.
2. Vibration. The game must be installed on a level surface.
   Do not install in an area such that the game would present an obstacle in case of an emergency (i.e., near fire equipment or emergency exits).

SPECIFICATIONS

This product is intended for use only with the adapter provided: Manufacturer: Blue Iron Holdings Ltd. Model: BI36-120300-U2
POWER SUPPLY: AC/DC Adapter
INPUT POWER: AC 100-240V~50/60Hz 1.2A Max
OUTPUT POWER: DC12V — 3A
MONITOR : 17” LCD
CABINET ASSEMBLED DIMENSIONS (WITHOUT RISER): 50” x 19.75” x 24” (127cm x 50cm x 60.9cm)

• The AC/DC adapter is used as a disconnect device.
• The AC/DC adapter of the apparatus should not be obstructed OR should be easily accessed during intended use.
• To completely disconnect the power input, the AC/DC adapter of the apparatus shall be disconnected from the mains.

ASSISTANCE OR SERVICE

Before contacting us for assistance or service, please check the “Troubleshooting” section in the User Manual. If you still have questions regarding your Arcade1Up product or require technical support. Contact Arcade1Up Customer Service at www.Arcade1Up.com and click on “Support”.

GAME SETTINGS

1. ROTATE THE DRIVING WHEEL TO SCROLL THROUGH THE GAME LIST
2. PRESS VIEW BUTTON TO ENTER GAME SETTINGS
3. MOVE THE SHIFT KNOB UP & DOWN THEN ROTATE THE DRIVING WHEEL TO ADJUST THE SETTINGS
4. SELECT “RESET TO DEFAULTS” THEN PRESS THE GAS PEDAL OR START TO RETURN THE GAME TO ITS ORIGINAL STATE
5. SELECT “SAVE & EXIT” THEN PRESS THE GAS PEDAL OR START TO CONFIRM

CAUTION
Servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
ALL PICTURES SHOWN ARE FOR ILLUSTRATION PURPOSES ONLY. THE ACTUAL PRODUCTS MAY VARY DUE TO PRODUCT ENHANCEMENT.

GAME CONTROLS

*ARCADE MAY TAKE 10-15 SECONDS TO POWER ON AFTER SWITCHING ON

1. ROTATE THE DRIVING WHEEL TO SCROLL THROUGH THE GAME LIST
2. PRESS THE GAS PEDAL OR START TO CHOOSE GAME
3. FOLLOW THE GAME CONTROLS BELOW FOR EACH GAME
4. PRESS THE GAS PEDAL OR START TO CONTINUE
5. HOLD START 5 SECONDS TO QUIT GAME
6. PRESS VIEW TO CHANGE DRIVER’S VIEW EXCEPT FOR RIDGE RACER™ & RIDGE RACER 2™

CALIBRATION
Please note: Driving Wheel / Pedals have been Calibrated at the factory and do NOT need to be Calibrated. Only Calibrate if after playing the calibration seem to be off.

HOW TO CALIBRATE YOUR DRIVING WHEEL & PEDALS IF IT GOES OFF:

1. Turn the machine OFF.
2. Hold down the START button and LIVE button at the same time & turn the machine back ON while continuing to hold the buttons.
3. Follow on-screen instructions.

WARNING
TO ENJOY A SAFE GAMING ENVIRONMENT
Please use the wall anchor kit that is included with the product.

WARNING
Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over:

• Set up Arcade1UP on a level floor.
• Never allow children to climb or hang on products.
• Always set up an anti-tip device!

The use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.

WARNING: Arcade1UP assumes no liability for improper installation or excessive loads placed on screws or brackets.
This wall anchor is not a substitute for proper adult supervision.

Make sure to locate your Arcade1UP on a flat surface

FCC RF RADIATION EXPOSURE STATEMENT:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

ISED RF RADIATION EXPOSURE STATEMENT:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

TROUBLESHOOTING

-Wakes/Plugs she hooked up sacredly. -ON/OF F SvAtch is In the OFF position.
-Upload switch on the back of monitors in the Off position.| 41Ae sure power cad is plugvd Into the val outlet mid there is the power to that outlet. (Rug othereledrical equipment Eta the pose outlet to make sure the outlet normal works.) -Make sure allures/Rugs are porky connected and al the way set in as dreaded in assembly instructions.
-Slide ON/Off Switch located on control ded to the ON position.
Game YI di turn OR but there is no sound.| -Wire/Plugs rare hooked up incorrectly. -VolumeSwitch is in the OFF position.| -Make sure Olivares/Rugs are propelled; connected and al the vay set in as directed in assembly instructions.
-Shade Volume Switch looted on control deck to the right
NOTE: Pushmkirre shit switch fight to Moose voter, left to Wellston
You hea sound tut there is no pkture.| -Wees/Plugs were hooked a) innately.| -Make sure SIN res/Rugs are property connected and al the way set in as directed in assembly instructions.
The gine amen is frozen.| – The game encountered a problem when processing dies data.| -Turn theOWOFF?ARMOR and then bak Mogan.
-You may need to RESET the game. Tum theOWOFF switch to the OFF position. Unplug the game from the wall outlet and wait6Oseconds to RESET the game. Rug the game back in and turn theOWCff swatch ban° OIL
Marquee won’t light up.| -Marquee power cad is not plugged in at the bad of the monitor.
-The marquee power cord is plugged into the nong trout.| -Make sure all1Mresiflugs are property mutated and al the way set in as {faded ii assembly list: maims.
The game screen looks p Oda ted or there a le
fines ruining through the image.| -11/ ires/P lugs yore looked up incorrectly.| -Mike sure al 111res1Pktgs ate propertyconnectedand all the way set In as directed in assembly instructions.
-You may need to RESET the gene. Tum the OWOFF switch to the off position. Unplug the game from the wall outlet and wait60 seconds to RESET the game. Rug the game back in and turn the/OFF switch bade to ON.
One of the buttons in the control deck is
stuck in the doom position.| -Debris may have gonen between the button and the button housing.| gate something ng thin Rea business card/and place it between the button and the button housingandside it bak and folth to loosen the debris.
Steering Wheel, G as or Brake Pedant
not functioning.| -The oblemuld has cane lose or is not fully seated al the way.
-The cab could be logged in to the mong location. -They may need to be recalibrated.| -Alice sure thecablesareconnectedand seated all the vay in.
-Make sure the cable is plugged into the erredlaation. _see016160n section in the owner Rana.
Gas Wake Pedal wil not push dorm.| -There could be debris underthe pedals preventing it from mining correctly.| -Kitesurf the underside of the pedal is a dear of arry debris that may affect the pedal’s movement.
You are not Ale to saol through the games
on the game selection menu or select a game.| -You need to tum t he steering rebuild to Suit to scroll through the ist of games and press the gas pedal to select agony.| -Make sure you steer Steel and gas pedal a correctly
plugged In./Agesure the VA es fa both the steering when and pedals a fury seated in the conned on ports.
You are able to scroll through the games on
the game selection menu, but your art
enter a game to begin playing.| -You may be pressing the rang button to enter there.| -Leant the gome control section in the instruction manual to make sure you me passim theerredbutton to enter the game.
You hae entered the game, but you can’t
get die game to start.| -You may be pressing the ‘gong button to start the game.| -Look at the gase (mud sateen In the Julia(1km manual to make sure you are pressing the theOaredbums to start the
Rame-
You have entered the gate, butyou can’t
ea the game to get lack to game selection
MAL| -You may be ffeSi ng the wrong button to exit the game.
-You may not be hall down the exit tenon long slough.| -Lock at the game control section in the instruction manual to make sure you ate pressing the erred button Iona the game. -Make sure youare holding the et baton doom fa 5 seconds total the game.
The control functions that an printed on the
madded do not match the gameplay on
the xreen for the game you an playing.| -You may be pressing the wrong game co-nerd buttons br the game mu are playing.| -look at the gene control sedim in the instruction manual to
make sure you are messing theGnatgamecontrolbuttons for that game.
-Wolof the same mitral lofting screen on the monitor to make sure you me messing the errectontrol buttons.
Thegamealnot let meselect 2or 3
doyen fora thosen game.| -Thegamenay only bea I or 2player game.| -Refer to the game control Stabil in the instruction mono/ to see how many players are able to play that game.

COLLECT THEM ALL

Colors, style, and decoration may vary.

©2021 Konami Digital Entertainment
©Konami Amusement
©2021 Viacom International Inc. All Rights Reserved.  Nickelodeon, Teenage Mutant Ninja Turtle, and all related titles, logos and characters are trademarks of Viacom International Inc.

Killer Instinct® Arcade © 1994 Microsoft. Microsoft, Killer Instinct, and the Killer Instinct Logo have registered trademarks of the Microsoft group of companies. Manufactured and sold by Tastemakers, LLC under license by Microsoft.

Battletoads ©1991, Battletoads Arcade ©1994, Killer Instinct © 1994, Killer Instinct Arcade © 1994, Killer Instinct 2 © 1995 Microsoft. Microsoft, Battletoads, the Battletoads logo, Killer Instinct, the Killer Instinct logo, Rare, and the Rare logo are registered trademarks of the Microsoft group of Companies.

visit Arcade1up.com
TO SIGN UP FOR OUR MAILING LIST AND SEE A COMPLETE LIST OF GAMES

RIDGE RACER™&©1993 BANDAI NAMCO Entertainment Inc.
RIDGE RACER 2™&©1994 BANDAI NAMCO Entertainment Inc.
RAVE RACER™&©1995 BANDAI NAMCO Entertainment Inc.
ACE DRIVER™&©1994 BANDAI NAMCO Entertainment Inc.
ACE DRIVER VICTORY LAP™&©1995 BANDAI NAMCO Entertainment Inc.

MADE IN CHINA
REV 08.24.21

References

• Arcade1Up | Officially Licensed Arcade Cabinets
• Arcade1Up | Officially Licensed Arcade Cabinets

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>