Navien RGX330-09PA Range Hood User Manual

Navien RGX330-09PA Range Hood

Safety Precautions

The following safety precautions will guide you through safe and correct use of the product to prevent unexpected hazards and damage. Please read the instructions and precautions carefully and use the product correctly.
This product is not intended for use by persons who lack physical, sensory, or mental abilities or who lack experience and knowledge of how to use the product safely without supervision or instruction (including children).

Safety Symbols

The following safety symbols are used in this manual.
All safety symbols indicate potential hazards, but do not include cautions for all dangerous situations that may occur while you are using the product. Therefore, you must pay careful attention to safety when using the product.

WARNING
Failure to heed the warning can cause serious injuries or death.

CAUTION
Failure to heed the caution can cause injuries or property damage.

WARNING

Installation

• Check if there are any damages before installing hood.

• Comply with the regulations on air emission.

• The distance between the cooktop and the range hood filter has to be at least 65cm.

• Make sure that the walls and ceiling are sturdy enough to hold the weight of the hood before installing.

• Installation should be done with at least 2 authorized professionals/technicians.

• When installing, make sure to wear work gloves and use all the given screws and anchors for mounting.

• Make sure not to damage any electrical cables during drilling.

• Install exhaust & flexible duct correctly to prevent any foreign liquids from flowing in.
  It may cause an electric shock.

• Make sure the outlet is 220V and grounded.

• Make sure the power cords are not damaged.

• Do not touch power plug with wet hands.
  It may cause a fire or an electric shock by short circuit.

• Do not connect the appliance to the mains electricity supply with an extension cord.

• Remove the protective film after installation.

Use

• Make sure to unplug the power cord before cleaning. (Should always wear work gloves.)

• Do not use inflammables such as paint thinner and benzene for cleaning.
  It may cause an explosion.

• Do not attempt to put fingers inside the hood or detach the filter during operation.
  It may cause serious injuries or burn.

• Failure to follow the cleaning instructions in the user’s manual may result in physical injuries or fire.

CAUTION

Use

• Make sure the power plug is clean.
  It may cause an electric shock.

• Hood must be operated for cooking.
  It may damage the product and shorten it’s life.

• If oil catches on fire, turn off the gas and unplug the power cord immediately.
  It may cause the fire to spread.

• Do not get too close to the appliance while cooking. It may cause physical injuries such as scratches or burn.

• Accessible parts may be heated when used with cooking devices.

• Do not attempt to remove the filter during or right after the operation.
  It may cause physical injuries.

• If gas leaks, do not touch anything electrical and immediately aerate the space.
  It may cause a fire or burn.

• Stop the operation when there is a power outage and resume once the power is restored.
  It may cause a fire or an electric shock.

• Do not attempt to light up any other substances on fire under the hood.
  It may cause a fire.

• Do not attempt to touch any electric parts.
  It may cause an electric shock.

• Do not touch the appliance with wet parts of body. It may cause an electric shock.

• Do not put any weight (bottles, cans, etc.) on the product.

• Any assembly or installation must be carried out by the authorized technicians.
  It may cause serious injuries or an electric shock.

• Children are not allowed to tamper or play with the appliance.
  It may cause serious injuries.

• Do not attempt to excessively pull or bend the power cord.
  It may cause a fire or an electric shock.

Cleaning Method

Clean every 3 months for optimal performance with longer life span.

CAUTION
Make sure to unplug the power cord before cleaning.

Filter Attachment & Detachment
The filter is made of aluminum. This product can last a long time if it is well-managed. Remove the filter by pulling the release handle down. Make sure the filter is completely dry before placing it back. Filter Cleaning
Leave the filter in the water that is mixed with a neutral detergent (dish soap) for 10 minutes and rinse it under water.

CAUTION
Do not leave the filter in for too long. It may discolor the filter. Exterior Surfaces

CAUTION
Wipe with damp soft cloth or non-abrasive sponge using liquid detergent, then rinse with clean water and wipe the surface dry to avoid water marks. Using other tools or detergents may result in rust or stains on the surface.

Standard Components

Check if there is any missing item.

• Hood + Duct Cover (x2)
• Installation Bracket
• Duct Cover Fixture
• Flexible Duct Ø125
• 540mm Cable Tie (x2)
• Duct Adapter Ø100
• Duct Adapter Ø100
• Screw2(5*14) (x4)
• Screw3(4*30) (x6)
• Anchor(6*30) (x6)
• User’s Manual
• Installation Template

Names of Parts

The following illustrates the names and functions of the product’s main parts.

Operation

The following illustrates the names of the switches and how to operate them.

Specifications

Power Consumption

| Motor| 90W
Lighting| 1W X 2
Wind Volume (Level 1/2/3)| 240 / 310 / 350 m3/h (100Pa) *Static pressure applied 100Pa
Wind Volume Control| 3 Levels Rocker Switch
Exhaust Hose| Inner Dia. Ø125 Flexible Hose
Filter| Aluminum Filter
Dimensions(WXDXH)| 898 X 532 X 650~800mm
Weight| Approx. 13.8 kg

Warranty Card

Model name|
---|---
Serial number|
Date of installation| (YYYY)| (MM)| | (DD)
Installer| Trade name:| | TEL :|

Warranty period: 5 years
Retention period for parts: 8 years

• This product’s warranty is only guaranteed as stated on the Warranty Card. (However, as for filters, which are consumable parts, you must follow the cleaning and replacement cycles given in the user’s manual.)
• The warranty period for free repairs is determined by your date of purchase. Be sure to fill in the installation date. (If the proof of the installation date is unavailable, 6 months after the date of manufacture will be used.)
• The warranty for the supply under a separate contract is applied according to the main contract.
• The retention period for parts is determined by the date of manufacture.

Free service

| Type of issue| Criteria for resolution
---|---|---
Within the warranty period| After the warranty period has expired
refund of purchase price or functional failure that may occur during normal use| An important part needs repair within 10 days after purchase.| rePfurond ocftpeuxrcchhaansgeeporrice|

Paid repair

An important part needs repair within 1 month after purchase.| Product exchange or free repair
The product needs important repair within 1 month after replacement.| Refund of purchase price
Replacement is impossible.
There is a product defect.| Free repair
The 3rd product failure caused by the same defect|

Product exchange or refund of purchase price

The 5th product failure caused by different defects
Repair is impossible.| Refund by deducting
flat depreciation
and adding 5% of purchase price or product exchange
Repair is impossible because a necessary part is not retained.
Damage during transport| Product exchange| –
Defects in installation| Free repair or reimbursement (Contractor’s responsibility)| –

Paid service

Refund or product exchange after deducting

| Paid repair
Repair is impossible.| |

• The problem is not a product failure and can be solved using the instructions or by making a simple adjustment without disassembling the product.
• Product failure caused by repair or modification by an unauthorized person and not by technicians from KyungDong Navien local dealers or Service Centers
• Product failure from natural disasters (fire, salt damage, earthquake, wind and flood, etc.)
• A consumable part that wears out normally during use needs to be replaced.
• Product failure caused by incorrect rating voltage, gas type, or gas pressure
• Product failure caused by external causes (external shock, products from other companies, etc.) and not due to product defects
• Product failure caused by improper handling, abuse, or misuse
• Product failure caused by failure to follow the instructions or precautions in the user’s manual
• Freezing caused due to negligence
• Product failure caused due to negligence

|

Paid repair

|

Paid repair

• You will incur a service charge if you request service for any situation that is not a result of product failure.
  Please read the user’s manual carefully before contacting a service center.

• This Warranty Card is exclusive to be used in the Republic of Korea. Store the Warranty Card in a safe place, as it will not be reissued.

Customer Service Center 1588 – 1144
KyungDong Navien Homepage www.kdnavien.co.kr
KyungDong Navien Online Mall www.navienhouse.com

Installation Guide

Hood Installation

CAUTION
Failure to follow the instructions below when you install the screws, brackets, or fixtures may cause electrical hazards.

User may need to purchase extra materials for installation depending on the type and condition of the wall.

1. Place the installation template to the wall keeping the distance between the bottom of the hood and the cookware base at least 65cm.
2. Drill holes (Ø6) on the installation template as indicated and insert the anchors. Place the installation bracket in the designated spot and fix the bracket onto the wall using screw3.
3. Install the body of the hood to the installation bracket and mount the two together using screw2.
4. Determine the place of the duct cover and drill holes (Ø6). Then, insert the anchors.
5. Place the duct cover fixture aligned with the drilled holes and mount it using screw3.
6. Fix the flexible duct using cable ties and complete the electrical wiring. Turn the appliance on to check if the hood is working well.
7. Measure the length needed for the duct cover and mount the upper duct cover to the duct fixture using 2 of the screw1. Place the lower duct cover aligned with the upper duct cover and mount it to the hood using 4 of the screw1.

Troubleshooting

Motor Not

Working.

|

• Check if the power cord is plugged in.
• Make sure the operational and indicated voltage match.
• Check if the electric fuse is disconnected.

Exhaust Performance is Deteriorated.

|

• Are there any foreign substances blocking the inlet?
• Is the filter clean?
• Check if the duct is clogged.

Abnormal Noise.

|

• Check if the hood is installed properly.
• Check if the duct of the inlet is clogged.

Light Does Not

Turn On.

| Were there any changes in the

voltage?

Before A/S Request

Oil Dropping from the Hood.

| Oil mists gather to form the liquid oil. It happens from cooking for a long time. This does not mean the appliance is a faulty product.

To prevent further problems, keep the hood in operation for another 15-20 minutes after cooking.

Noise from External Factors.

| The noise from the following reasons do not mean the appliance is a faulty product.

• Noise from wind flowing in from the outside.
• Noise caused when the hood is not in operation.

Range Hood Fire

Suppression

System.

| The following cases are not applicable for A/S. Please contact the indicated fire extinguisher company.

• Gas fluid leaking.

• Gas circuit breaker alarm goes off.

• If there are further problems, unplug the power cord and contact either KD Navien Customer Service or an agency where the appliance was purchased from.

• For disposal, attach the waste sticker on the appliance and dispose it in a designated place. Stickers can be purchased from local community center.

• Please read and understand all instructions and precautions in this manual thoroughly for your safety.

• Users should keep this manual for future reference.

• A Warranty Card is included in this manual.

• This product is exclusive to be used in the Republic of Korea. FOR KOREA UNIT STANDARD ONLY

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>