Cylinda 150-10 Solo Alliance Flat Fan User Manual
- June 5, 2024
- Cylinda
Table of Contents
Cylinda 150-10 Solo Alliance Flat Fan
SAFETY INSTRUCTIONS
Please read this installation and user guide carefully before installing and using the product, paying special attention to the safety instructions. Keep the instructions for reference or for the next owner. Disconnect the product from the power supply prior to cleaning or maintenance.
- The diversion of exhaust air must be carried out in accordance with instructions issued by the appropriate authority.
- Exhaust air must not be directed into flues that are used for fumes from items such as gas, wood or oil-burning stoves or fireplaces.
- The distance between the stove and the product must be at least 44 cm. For gas hobs, the distance should be increased to 65 cm. Adjust accordingly if the stove manufacturer recommends a higher mounting height. N.B. If the product has a stove alarm or stove guard, it must not be mounted over a gas hob. See separate instructions.
- You must not flambé food underneath the product.
- For safety reasons, the installation and replacement of cables or other types of connectors should only be carried out by a qualified professional.
- If the product is to be used at the same time as products that use energy sources other than electricity, i.e., gas hobs, gas, wood or oil-burning stoves or fireplaces, etc., the room must have an adequate supply of air.
- The product may be used by children from 8 years of age and persons with mental, sensory or physical impairment, or a lack of experience and knowledge, provided they are given information about how the product is to be used.
- Children should not be allowed to play with the product. Children must not undertake cleaning or maintenance of the product unsupervised.
- Accessible parts of the product may become hot when food is being prepared.
- A fire is more likely to spread if the product is not cleaned as frequently as indicated.
N.B. The developer or proprietor is responsible for ensuring installation is carried out correctly and complies with the applicable building regulations.
GENERAL INFORMATION
The product features LED lighting (6.5 W), aluminum filters, an EC motor and the Easy Clean system.
FUNCTIONS
- A. Lighting.
- B. Ventilation mode. Open damper. Returns to basic ventilation after 60 minutes.
- C. Open damper. Speed 1 on fan motor.
- D. Open damper. Speed 2 on fan motor.
- E. Open damper. Speed 3 on fan motor.
- F.
- Extension of timer (+ 30 minutes). Can be activated when one of buttons B-E is activated. Then switches to remaining time for activated mode.
- Filter guard. If the filter guard is activated (see Programming below), the LED will flash when the filter needs to be cleaned. After cleaning, press and hold button F for 2 seconds to reset the system.
The damper and the motor for the alliance hood close automatically after 60 minutes and the central fan returns to standard mode. It can also be returned to standard mode by pressing in the activating button one more time. It is a good idea to turn on the fan before starting to cook, as this prevents cooking smells spreading into the room. Adjust the speed of the fan depending on the type of food you are preparing. If possible, allow the fan to run in ventilation mode for a few minutes after you’ve finished cooking. You may also wish to use ventilation mode when the oven is in use or after using the dishwasher. The product is fitted with a filter guard. To activate/deactivate the filter guard, see below.
Programming
-
Start programming: press and hold buttons A and B for 3 seconds so that they both flash 3 times. Programming mode will then be active for 30 seconds.
-
Select function: press the button for the selected function to activate/deactivate the function.
The LED on the button lights up when the function is activated. -
To save a program: press and hold buttons A and B for 3 seconds. Buttons A and B will flash twice to show that the program has been saved.
Attention!
If the product has a stove alarm or stove guard, see separate instructions.
CARE AND MAINTENANCE
Cleaning the Filter
The cooker hood should be cleaned with a damp cloth and washing-up liquid. With nor-mal usage, the filters must be cleaned at least every other month. Clean more often after intensive use.
- Remove the grease filter by opening the snap retainer, Handle the filter carefully, taking care not to bend it.
- Soak the filter in a solution of warm water and washing-up liquid.
- The filter can also be washed in a dishwasher. Refit the grease filter after cleaning, making sure it snaps firmly into place.
Cleaning Other Parts
-
The interior of the cooker hood, removable parts and the damper should be cleaned at least twice a year.
-
Remove the bottom plate by pushing the snap retainers in the direction of the arrows.
-
Release the blower by bending the snap retainer outwards in the direction of the arrow (1) and pushing the blower away from you and down (2),
-
Release the impeller by pulling in the direction of the arrow,
-
Clean the bottom plate, blower and impeller using warm water and washing-up liquid.
-
The blower and impeller can also be washed in a dishwasher. After washing and drying, assemble the parts in reverse order.
-
Refit the impeller. Make sure that it is level in the groove on the motor.
-
Refit the blower by inserting the supports in the rear of the hood (1). Check that the damper shaft is correctly positioned in the blower (2). Bend up the blower
-
Make sure all the snap retainers fit onto the cooker hood lugs.
- Twist the blower (1) into the lugs (2).
- Press the blower’s snap retainer back into the lug
Attention!
Check that the parts snap firmly into place.
TROUBLESHOOTING
Check that the fuse is intact. Go through all the functions to check what is
not working. Start by disconnecting the product from the power supply and
switching it on again. Check that the connector is not bent or twisted at the
connection point.
Attention!
If the product has a stove alarm or stove guard, use the separate instructions
for troubleshooting.
SERVICING
Before contacting servicing, check the product label and note down the FUN number, S/N number and manufacturing date of the product. The product label is located on the left side, underneath the filter/bottom plate.
Contact Cylinda Service
Tel. +46 0771-25 25 00 or visit:
www.cylinda.se/service
They can help you fix the problem or refer you to the nearest service agent
for fast and effective service. The product is covered by the relevant AP-PliA
provisions.
ENVIRONMENTAL INFORMATION
The main raw materials used in the product are:
- Metals: stainless sheet metal, galvanized sheet metal, zinc, aluminum
- Plastics: polypropylene, polyamide, polycarbonate, polybutylene terephthalate (PBT)
- Glass
All components comply with the RoHS Directive.
PACKAGING AND PRODUCT RECYCLING
The packaging should be deposited at your nearest recycling point.
The symbol means that the product must not be treated as household waste. It
should in-stead be taken to a collection point for the recycling of electrical
and electronic components. By ensuring that the product is dealt with in the
correct manner, you are helping to prevent the adverse environmental and
health effects that could arise if the product was dis-posed of as regular
waste. For further information on recycling, contact your local authority or
waste disposal service, or the store where you purchased your product.
ECO–DESIGN DIRECTIVE
The product has been tested in accordance with and meets the eco design
requirements of European Regulation 66/ 2014.
ELECTRICAL INSTALLATION
Electrical connection for 230 V~ earthed.
The product is supplied with a cable and earthed plug for connection to an
earthed socket. The socket should be accessible after installation is
complete.
The junction box or wall socket must be accessible after installation is
complete.
If the connector is damaged, it must be replaced with an equivalent special
cable from the manufacturer or their service agent.
INSTALLATION
**ADJUSTING AIR FLOW
**
Note : Damper adjustment and speed changes must be carried out by a
qualified professional
Setting the damper:
The air flow is adjusted with the aid of the damper. The damper can be
accessed for adjustment by removing the filter, underplate and fan housing.
Changing the speed: The speeds of the product can be changed by reprogramming
via the switch
Basic flow
- A Basic ventilation is set by moving the sliding damper
- B to the desired position according to marking
**BASIC VENTILATION
**
Adjusting diagram
-
LpA
The A-measured sound pressure level at 10 m² Sabin -
LWA
The A-measured sound pressure level relatively 1pW
Dimensioning diagram
Documents / Resources
|
Cylinda 150-10 Solo Alliance Flat
Fan
[pdf] User Manual
150-10, 160 10, 170 10, 160RF 10, Solo Alliance Flat Fan
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>