globe electric 50115 Smart WiFi LED Strip Light Instruction Manual
- June 5, 2024
- Globe Electric
Table of Contents
globe electric 50115 Smart WiFi LED Strip Light
Thank you for selecting Globe as your smart home solution. With proper care, this product will provide years of pleasure and enjoyment.
SMART WI˜FI LED STRIP LIGHT
Check out the installation video on our website: globe- electric.com/smart
SAVE THESE INSTRUCTIONS
CAUTION IMPORTANT SAFETY INSTRUCTIONS
LIMITED WARRANTY: This strip light is warranted to last 2 years from the
date of purchase based on use of 3 hours per day. If it fails before that
time, we will replace it. Send Globe Electric the strip light, proof of
purchase and register receipt along with your complete name and address. See
caution text for proper use. This warranty is void if this product is misused
in any way. This replacement is the sole remedy available and liability for
incidental or consequential damage is expressly excluded. This device is not
intended for use with emergency exit fixtures or emergency exit lights,
photocells and electronic timers. Do not use where directly exposed to water.
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment. This Class B digital apparatus complies
with CAN ICES-005(B).
WARNING: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment. NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate
the receiving antenna. Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. Consult the dealer or an experienced
radio/TV technician for help.
FEATURES
- Indoor use only
- Dimmable: 10% – 90% brightness
- RGB: choose from a full spectrum of colors
- Set schedules and control your light from anywhere
SPECIFICATIONS
wireless type: 2.4GHz | working wattage: Max 6.5W total 2m |
---|---|
wireless standard: IEEE 802.11b/g/n | USB input: 5V DC |
10mm wide, 2m long / 6.5ft | USB cord length: 1.12m / 3.8ft |
standby wattage: 0.2W |
RF EXPOSURE
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This device should be installed and operated with
minimum distance 20cm between the radiator & your body.
USER MANUAL NOTICE FOR LICENSE˜EXEMPT RADIO APPARATUS
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device. CAN
ICES-005 (B).
RADIATION EXPOSURE STATEMENT:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
FCC RESPONSIBLE PARTY
Globe Electric
2264 East 6th Street
San Bernardino, CA 92410
www.globe-electric.com
PRE˜INSTALLATION
Planning Installation
Compare all parts with the “Hardware Included” section. If any part appears
missing or damaged, do not install this product and contact the Customer
Service team at 1-888-543-1388 or
e-mail to info@globe-electric.com.
Tools Required
Philips head screwdriver
Hardware Included
NOTE: Hardware is not shown to actual size.
Item | Quantity |
---|---|
smart device | 1 |
adhesive tape | 1 |
mouting bracket | 4 |
screws | 8 |
INSTALLATION
-
Step 1
Before mounting, plug the USB cable into a USB port or USB power adaptor. Note: the Smart LED Strip Light requires minimum 1A of power to operate. Follow the “Connecting Instructions” (next page). -
Step 2
Once the device has been connected successfully, select your mounting location and ensure the surface area is clean. Warning: the mounting brackets are not to be used on Monitors, TV’s or any electronic devices. -
Step 3
Remove the liner from the back of the Strip Light to expose the adhesive. -
Step 4
Mount the Strip Light. -
Step 5
Use the included adhesive tape to secure the Smart Controller. -
Step 6
For added stability, use the included mounting brackets with the screws.
CONNECTING INSTRUCTIONS
Let’s get started!
-
Download the Globe SuiteTM app f rom the
App Store or Google Play to your mobile device -
Launch the Globe SuiteTM app
-
To register, enter your email address, create a password, then log in to the app
OR -
Log in if you already have an account
Verify your network
- Verify your network and ensure your mobile device is connected to a 2.4 GHz Wi-Fi channel
- Consult your router documentation for detailed instructions on how to change wireless settings
Scan mode
- Power on your device
- Select the “+” symbol on the top right hand corner
- Follow instructions within the app
- If your device is flashing rapidly and fails, try using EZ Mode
EZ mode
- Select the “+” symbol on the top right hand corner
- Select “Manual”
- Select your product type and follow the instructions within the app If the connection fails, try using AP mode
AP mode
- Select the “+” symbol on the top right hand corner
- Select “Manual”
- Select your product type
- Open the menu on the top right hand corner and select “AP mode” Follow the instructions within the app
- You’re good to go!
Did you know?
Most modern routers are dual-band, meaning they support both 2.4 GHz and 5 GHz
channels. The most common wireless options are:
- Mixed: The router will broadcast both 2.4 GHz and 5 GHz simultaneously under the same SSID. The device will choose which to connect to based on multiple variables (congestion, distance to router, etc.).
- 2.4 GHz: Broadcast only on this channel
- 5 GHz: Broadcast only on this channel
- Dual 2.4 and 5 GHz using Separate SSIDS: Router will broadcast both channels and user manually decides which to connect to
Since 1932, Globe has taken pride in offering products of the highest quality,
and a level of service unparalleled in the industry. Should you encounter any
difficulties, have any questions or simply wish to offer us your valuable
feedback, you may contact us in the following ways:
Toll Free Telephone: 1-888-543-1388
(North America Only) / Toll Free Fax:
1-800-668-4562
(North America Only)
E-Mail: info@globe-electric.com
Mail: Globe Electric Customer Service Department 150 Oneida, Montreal, Quebec,
Canada H9R 1A8
Please visit our website to discover other quality Globe products: http://www
.globe-electric.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>