Globe Electric GE50587 Smart Dimmer Switch User Guide

June 5, 2024
Globe Electric

Electric GE50587 Smart Dimmer Switch
User Guide
**SMART DIMMER

**

Smart User Guide
Thank you for selecting lobe as your swart home solution with proper care, this product will provide years of pleasure and enjoyment
Check out product videos on our Youtube channel, on the Globe Sart Home – Amnacon Certified for Humans ply/st!

SAVE THESE INSTRUCTIONS

**** Most electrical accidents are caused by carelessness erg ignorance. if you combine a basic icncieci go of electricity, a healthy respect for It, and the dawn of common sense, you can wispy added many household alt repaints Here are some basic guidelines for working with electricity:

  • Before working on a draught, go to the main service panel and remove the luso cx trip tho breaker that controls that circuit Tapes sign to the panel warning others to leave the circuit alone while you work
  • Reeve touching any wire, use a voltage tester to maim aura It’s rut Ilea When aver you check fee voltage In a receptacle, check both outlets—each may be compiled by a separate wiring circuit
  • To protract chi Id rerobce safety coders over any unused outlets
  • Always work with enough light to see when you are denied; It’s easy to make mistakes when you’re working in dim light

Before resembling your smart switch Extras TURN OFF THE POWER and consult a qualified licensed electrician.

This Smart Dimmer Is warranted w a fast year from the date of purchase. Mit falls Wore that time. who replaces It Send Globe Boat ric the Smart Switch, proof &purchase and register product along Wth your cant: Alta name and address See catrtdontasS1br proper UM. !his warranty is void If this product Is misused In any way. This replacement Is the solo remedy aver able and liable for Incidental or consequential damage is expressly excluded.
For use only in UMW HZ circuits Risk of ale: triad shock. Do not open, no user-senAcesb Is parts inside. This device is not intended kw used with emergency exit fixers or emergency: alight; photocells and 1310070(11C timers Do not use whore directly exposed to water. tf this emotion is unbearable for the application, fol know the manufacturer’s instruction for replacing the device. The minimum operating temperature is -20•C
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions. 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
RF Exposure
Is the equipment complete with Irix radiation exposure limits eat? oath for an uncontrolled environment, This device should be installed and operated with a minimum distance2Oar between the radiator your body.
User Manual Notke fa License Drinpt Radb Apparatus
WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates. uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. the user is encouraged to try correct the interference by one or more of the following measures:

  • Reorient the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

INTENDED USE

  • This product is intended to be used as a wall switch and a dinner to control incandost and Led light bulbs as part of permanent figures. ls intended to replace a standard switch receptacle tt can be connected and controlled tough W-Fl connection with Ara. zon Aleo6s a.pp 0r other external Alexa butt-in devices
  • intended for households only
  • intended to bet in«dry indoor areas only

FEATURES

  • Replace existing on/off or dimmer switches and make them smart
  • Manually or remotely control your dimmer with the Amazon Alexia app
  • Pair with Amazon Echo to control your dimmer through voice commands
  • Set schedules and control your dimmer from anywhere

SPECIFICATION

Switch type Single polo + 3-Way
Dimming Method Triad dimming
wiring wire to wire connection

The neutral wire is required
Rated input voltage| 120Vac / 60Hz
Input Voltage Range| 108-132Vac
Output voltage| Dimmed (1201/ac Max.)
Maximum Load| Incandescent 450W max.
LED:TR: NV max
Standby Power| IC OS W
Start-up Time| .41 second
WTrels control Module| Wi-fl 2461-TZ, IEEE 80271 Wein
Bluetooth Low Energy
Does not support 5GHz networks,
BLE only for pairing phone and device

PRE-INSTALLATION

Planning Installation
Compare all parts with the “Hardware Included” section. If any part appears missing or damaged, do not install this product and contact the Customer Service team at 1-888-543-1388 or e-mail info@globe-electric.com.

Tools Required

Hardware includes

NOTE Hardware is not shown to actual size.
A GROUND wire (green)
B LOAD wire (red)
C TRAVELER wire (brown)
D NEUTRAL wire (white)
E LINE wire (black)
F Air gap switch
G Status indicator
H On/off switch
I decrease the brightness button
J increase brightness button
K Main unit
L Twist-on wire connector x
M #6-32×27/32″ machine screw x2
N #6-32x 13/16 fat head screw x2
O Two-piece wall plate
P Wire label

STATUS INDICATOR & CONTROLS

Status Indicator Light Green Blinking MK% progress
Amber Light is off
Indicator is off Night Is On
Red and Green blinking alternately Factory reset is complete
Solid Green for 3 seconds atricanrsabsttaired
Red blinking No Network
Solid Red Setup has timed out
On/Off Buttons Short press power button lcls} TUm the light on/off
Press and hold the power button (>104 Factory test

Enter pelting mode
Brightness Button| Press A| Increased brightness
Press v| Decreased brightness
Press and hold the A and v at r same time| Reset to the lowest dimming brightness
Air Cap Switch| Pull out
Pull-in| Device Switch Power off Device Switch Power on

INSTALLATION

WARNING: Improper wiring of any electrical device can cause fire, serious injury or death. Always consult a qualified licensed electrician who will ensure the switch is installed in accordance with local electrical codes and regulations. Before starting the installation, ensure the power is disconnected at the circuit breaker and test existing switch with a voltage tester.
CAUTION:

  • Make sure that the power at the circuit breaker is off before wiring.
  • A neutral wire is required. Confirm the wall box contains a neutral wire (typically white), Look for a bundle of white wires folded in the back of the switch box Most homes built after 1978 have neutral wires.
  • The wire colors indicated in this manual are the common colors and may differ in some homes please contact an electrician if you have different wire colours.
  • Ensure the wire conductors are securely fastened to each wire

Single pole connection refers to when l light is controlled by a switch.
The Traveler (brown) wire is not needed for this scenario.
For lights switched from ONE location.
For retrofit applications,

  1. Rerove the existing wall plate and screws from the wall after having turned off the power at the circuit breaker and tested the outlet with a voltage tester.

  2. Remove the existing switch from the wall and label the wires with the appropriate stickers included in the box.

  3. Ensure these wires are available:
    a. Line (black)
    b. Ground (green, or yellow/reen)
    c. Neutral (white)
    d. Load (red)

  4. Disconnect the wiring from the old switch.

  5. Connect the Smart Switch to the existing wiring:
    a Connect Ground (green, A] wire on the switch to the Ground (green)] wire from the switch box
    b. Connect the Line (black, E) wire on the switch to the Line (black] the wire from the breaker box
    c. Connect the Neutral (white, D) wire on the switch and the Neutral (white) wire coming from the light to the Neutral (white) wire from the breaker box
    d. Connect the Load (red, B)} wire on the switch to the Load (red) the wire from the light

  6. Ensure the included wire connectors are securely fastened to each wire. The Traveler (brown, C) wire needs to be covered with a wire connector even if not in use

  7. Restore power at the circuit breaker switch to test if the switch works.

  8. Insert the switch into the wall and scan the 2D barcode to complete the deice setup

  9. Once the device setup is successful and connected to the app, cover the wall plate with the screws provided.

3-WAY
For lights switched from  TWO locations.
1 SMART SWITCH + 1 TRADITIONAL 3-WAY SWITCH

  1. Remove the existing wall plate and screws from the wall after having turned off the power at the circuit breaker and tested the outlet with a voltage tester.

  2. Remove the existing switch from the wall and label the wires with the appropriate stickers included in the box

  3. Ensure the wires are available in box l and box 2
    Box 1 (wired to electrical box):
    a) Neutral (white)
    b) Neutral (white] c) Ground (green, or yellow/green)
    d) Traveler (brown) x 2
    Box 2 (wired to light fixture)
    a) line (black] b) Ground (green, or yellow/green)
    c) Load (red)
    d) Traveler (brown) x 2

  4. Disconnect one traveler wire (any one of the 2 traveler wires is ok) of the traditional 3-way switch in box 1 then connect this traveler wire to Line in box l to change it to the Line for box 2

  5. Disconnect the wiring from the old switch.(Box 2)

  6. Connect the Smart Switch to the existing wiring:
    a. Connect the Ground (green, A) wire on the switch to the ground (green) wire from the switch box
    b. Connect the Line (black, E) wire on the switch to the Line (black) wire from the breaker box
    c. Connect the Neutral (white, D) wire on the switch and the Neutral (white) the wire coming from the light to the Neutral (white) wire from the breaker box
    d. Connect the Load (red, B) wire on the switch to the Load (red) the wire from the light

  7. Ensure the included wire connectors are securely fastened to each wire. The Traveler (brown, C) wire needs to be covered with a wire connector even if not in use

  8. Restore power at the circuit breaker switch to test if the switch works

  9. Insert the switch into the wall and scan the 2D barcode to complete the device setup

  10. Once the device setup is successful and connected to the app, cover the wall plate with the screws provided. 

**SMART SWITCHES

**

NOTE: to produce a functional J-way connection, both smart switches need to be the same brand. This switch is not compatible with other brands.
For retrofit applications.

  1. Remove the existing wall plate and screws from the wall after having turned off the power at the circuit breaker and testing the outlet with a voltage tester.
  2. Remove the existing switch from the wall and label the wires with the appropriate stickers included in the box

Smart Switch #
i. Line (black] i. Ground (green, or yellow/green)
iii. Neutral (white)
iv. Traveler (Brown)

Smart Switch #2 (wired to light fixture)
i. Line (black)
ii. Ground (green, or yellow/green)
iii. Neutral (white)
Iv. Load (red)
v. Traveler (Brown)

  1.  Connect the Ground (green, A) wire of both switches to the Ground (green) wire from the breaker box.
  2. Connect the line [Pack E) wire of both switches to the Line (black) wire from the breaker box
  3. Connect the Neutral (white, D) wire on switch 2 and the Neutral (white] wire coming from the light to the Neutral (white) wire from the breaker box
  4. Connect the Neutral (white, D) wire on switch 1 to the Neutral (white) wire corning from the breaker box
  5. Connect the Load (red, B) wire on switch 2 to the Load (red) wire from the light
  6. Connect the Traveler (brown, C] wire on switch 2 to the Traveler (brown) of switch I.
  7.  Ensure the included wire connectors are securely fastened to each wire.
  8. Restore power at the circuit breaker switch to test if the switch works
  9. Insert the switch into the wall and scan the 2D barcode to complete the device setup
  10. Once the device setup is successful and connected to the app, cover the wall plate with the screws provided.

CONNECTING INSTRUCTIONS

  1. Download the Amazon Alexa app.

  2. Power on your device
    Ensure your smart switch is installed correctly and powered on.

  3. Scan barcode

  • Launch the Amazon Alexa app.

  • Select Add a Device”.
    Select “Switch”, locate Globe Electric and follow the in-app instructions on how to scan the 20 barcodes.

  • Scan the 20 barcodes on the product
    [There are two locations, one at the front top, and another at the sideway.)

Please note
The device is automatically in pairing for S minutes once powered on. When you scan the barcode, the white light will flash indicating the pairing is successful. If within S minutes, it does not connect, turn the device OFF and ON again to re-enter pairing mode.
Don’t have a barcode?
Select “Don’t have a barcode” in the Alexa app and follow the in-app instructions on how to connect without a 2D barcode.
How to factory reset device
If you are struggling to set up your device, or if the device was already connected to a network, perform a factory reset by following the instructions below
You may notice your lights are flickering after installing the dimmer.
To correct this, you will need to adjust the product to the lowest dimming brightness level.
To do so:

  1. Press the + and – buttons together for 5 seconds. The status indicator light will blink rapidly.
  2. Hold either the + or -to set the lowest dimming brightness level. Adjust the light until the flickering stops.
  3. To get out of this mode, repeat step 1 until the status indicator light stops flashing (will stay on).

Cheak your product videos on our Youtube channel From the Clobex Amazon Alexa Smart app.

FCC Repor.bl party
Glob Leete
1sot Shoernaleer Awe, Norwalk, CA 90650 www.globola¢tie.com
Since 1932, Globe has taken pride In offering products of the highest quality, and a level of service unparalleled in the industry. Should you encounter any difficulties, have any questions or simply wish to offer us the valuable feedbeck you fray contact us in the following ways:
Toll-Free Telephone 1-e88-543-1388 (gore, America Only)
Toll-Free Fax:1-800-668-45E2 (North America only)
E-Mail: Infoegloho-electric.com
Mall: Globe Electric Customer Sondice Department 150 Onside, Montreal, Quebec, Canada )49R lAB
Please visit our website to (Vacant other quality Globe products http://www .globe-electrIc.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Globe Electric User Manuals

Related Manuals