sygns Moss and Plant Walls Panel Instruction Manual

sygns Moss and Plant Walls Panel Instruction Manual

General Information

PANELS CANNOT BE FIXED ON A BRITTLE, WET, CRUMBLING SURFACE

The surface on which panels are installed must be stable, smooth (each panel must align perfectly to the wall) and clean (free of dirt, dust, grease stains). In the case of unstable surface, it should be reinforced with OSB panels (panels thickness need to be evaluated each time base on product weight).

INSTALLATION SHOULD BE CARRIED OUT STEP BY STEP IN ACCORDANCE WITH THE DESCRIBED INSTRUCTIONS.

Tools Required

1. Drill-driver
2. Drill bit
3. Level
4. Measure
5. Pencil
6. Expansion bolts / dowels
7. Hammer

Please ensure that you have the right Drill bit for your walls.

Disclaimer

Moss products should be used for the intended purpose in accordance with below points.

1. Panels must be used in enclosed rooms that are dry and protected against harmful atmospheric conditions.
2. Humidity levels in the room for moss must be maintained from 35 to 65%. (For most mosses and lichens as they may get dry and again get softened without harm to the product). The exception is jungle moss, for which the humidity levels in the room must be maintained up to max 65% (Humidity drop below 35% is acceptable and is not harmful).
3. It is not recommended to install panels closer than 1 m from active heat sources (heaters, stoves) which might overdry mosses and plants.
4. It’s forbidden to¾
   • Water, mist, spray with water. If air humidity drops below 35% moss should be treated with use of an air humidifier
   • Cut or trim product
   • Touch, tear, pull out or crumple
   • Put in the mouth nor eat
   • Expose to direct contact with heat sources, including fire (heaters, stoves, fireplaces, radiators, candles, etc.)
   • Expose to chemical substances, cleaning agents (even the mild ones) and any liquids at all
   • Dye moss and plants on your own
   • Expose to permanent very intense sunlight or artificial lighting

Product

Installation

Assembly Scheme

1. If your design consists of several boards in a package, there will be ASSEMBLY SCHEME attached. Prior to the assembly, make sure the number of moss panels in the package is the same as on ASSEMBLY SCHEME.
2. Numbers from ASSEMBLY SCHEME can be found on the back of each moss panel.

Surface Preparations

1. Level the first panel and mark the edge of the panel on the wall.
   

Wall preparation for Dowel

1. Drill holes in the wall, install the appropriate mounting dowels, screw the panel to the wall.
   

Moss Panel Preparations

1. Being careful of moss, drill through the panel, leaving mounting points on the wall.
   

Montage Moss Panels Side by Side

1. Align the next panel to the one already installed and repeat the installation steps.

General Information

PANELS CANNOT BE FIXED ON A BRITTLE, WET, CRUMBLING SURFACE

The surface on which panels are installed must be stable, smooth (each panel must align perfectly to the wall) and clean (free of dirt, dust, grease stains). In the case of unstable surface, it should be reinforced with OSB panels (panels thickness need to be evaluated each time base on product weight).

INSTALLATION SHOULD BE CARRIED OUT STEP BY STEP IN ACCORDANCE WITH THE DESCRIBED INSTRUCTIONS.

Tools Required

1. Drill-driver
2. Drill bit
3. Level
4. Measure
5. Pencil
6. Expansion bolts / dowels
7. Hammer

Please ensure that you have the right Drill bit for your walls.

Disclaimer

Moss products should be used for the intended purpose in accordance with below points.

1. Panels must be used in enclosed rooms that are dry and protected against harmful atmospheric conditions.

2. Humidity levels in the room for moss must be maintained from 35 to 65%. (For most mosses and lichens as they may get dry and again get
   softened without harm to the product). The exception is jungle moss, for which the humidity levels in the room must be maintained up to max
   65% (Humidity drop below 35% is acceptable and is not harmful).

3. It is not recommended to install panels closer than 1 m from active heat sources (heaters, stoves) which might overdry mosses and plants.

4. It’s forbidden to:

   • Water, mist, spray with water. If air humidity drops below 35% moss should be treated with use of an air humidifier
   • Cut or trim product
   • Touch, tear, pull out or crumple
   • Put in the mouth nor eat
   • Expose to direct contact with heat sources, including fire (heaters, stoves, fireplaces, radiators, candles, etc.)
   • Expose to chemical substances, cleaning agents (even the mild ones) and any liquids at all
   • Dye moss and plants on your own
   • Expose to permanent very intense sunlight or artificial lighting.

Product

Installation

Assembly Scheme

1. If your design consists of several boards in a package, there will be ASSEMBLY SCHEME attached. Prior to the assembly, make sure the number of moss panels in the package is the same as on ASSEMBLY SCHEME.
2. Numbers from ASSEMBLY SCHEME can be found on the back of each moss panel.
   

Surface Preparations

1. Position the product on the wall. Mark the location of the panels using our template guide provided in your order.
   

Montage Moss on Wall

1. Hang moss on wall and plug in the electrical cord to check if lights are working.
   

Wall preparation for Dowel

1. Attach the template to the wall and drill holes in the marked area.
2. Install the appropriate wall dowel (depending on the wall type).
3. Screw in the screw until it sticks out of the wall sufficiently for
   hanging.

WARNING

The installation should only be undertaken by qualified personnel.
Steps if the electric installation is already prepared.

Montage with existing Electrical Installation

1. Take out power cord cable out of the junction box.
2. Connect power cable from existing electrical instalation to electrical junction box.
3. Hang moss wall and check if lights are working.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>