Shenzhen KELIC002AXOB CElLING FAN REMOTE CONTROL (WIFI) User Manual
- June 5, 2024
- Shenzhen
Table of Contents
User Manual
INSTRUCTION FOR CEILING FAN REMOTE CONTROL WIFI
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This deuce may not cause harmful interference, and (2) this device must accept any interference received, interference that may cause undesired operation.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.
INSTAIIATION&ATTENTION
- Make sure the circuit breaker had been turned off before installation.
- Electrical installation should be performed by a qualified licensed electrician.
- Spliced conductors should be turned upward and pushed carefully up into the outlet box.
- The receiver should be within 5 meters of the router, so as not to miss the WIFI signal.
SPECIFICATION
| Input Voltage | Max Fan Power | Max Light Power | FAN Timing Speed |
|---|---|---|---|
| 100V/60Hz-240V/50Hz | 145W | LED/150W Incandescent/500W | 1H/2H/4H/8H H/M/L/STOP |
Wireless Transmission: RF 433MHz/WIFI 2.4GHz network
Wiring schematic diagram for receiver and remote function
Install the mobile APP and connect to WIFI
You should select App store or google play store, download and install the app SMARRIFE, then register your user’s account, create and name your smolt home, such as ‘My home’, (My office’, etc.
WIFI SETTING (2.4GHz network. The device should be nearby the router):
Switch on the ceiling fan, then press and hold down the ‘SR on the remote for
3 seconds, when you hear `B—‘ A single short beep, indicating that the
receiver enters the distribution nem& state.
There are two ways to connect the network. You can follow one of that two:
- Rapid configuration(Bluetooth support, the preferred recommended):1.Take your smart mobile phone WIFI and Bluetooth on,2. Open the SMARTUfE App, just a moment, find the device, and pop up the popover shown in ‘FIGURE 1’, 3. Enter the WIFI user name and password when prompted. Click the ‘draw red circle’ option and follow the steps from figure Ito figure 6 to complete the WIFI connection.
| 
| 
---|---|---
| 
| 
- Single-mode connection(EZ): 1. Take your smart mobile phone WIFI on, and open SMART LIFE App,
- Click ‘+’ Add Device in the upper right corner of the interface,
- select ‘Small Home App’, Click Fan,
- enter the WIFI user name and password, dick next,
- According to prompts to Finish the connection step by step.
Now, you can use your mobile equipment remotely control the ceiling fan
&light. To facilitate the management of devices, the various smart devices in
the home should be named.
TIPS: If you have more than one smart device in the same house, such as
light or fan or others. name each device individually in the SMART LIFE App so
that the voice assistant can recognize it
Enable and supported voice assistant
ALEXA
GOOGLE
****TMALL GENIE
Purchase and install voice assistant systems and devices such as Amazon
speakers, And scan the smart devices, and then all the smart devices will
appear in the voice assistant system. and now, you can use the voice assistant
to control your ceiling fan&light.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>