wiltec 60237 Wall-Mounted Workshop Cabinet User Manual

: June 5, 2024
: wiltec

Table of Contents

Wall-Mounted Workshop Cabinet
Introduction
Product description
Cleaning and care
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

60237 Wall-Mounted Workshop Cabinet
**User Manual

**

Operation Manual Wall-Mounted Workshop Cabinet
60237, 60238

Wall-Mounted Workshop Cabinet

Illustrations similar may vary depending on model
Read and follow the operating instructions and safety information before using it for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps, and technical data can differ insignificantly.
Updating the documentation If you have suggestions for improvement or have found any irregularities, please contact us.
The information contained in this document may alter at any time without previous notice. It is prohibited to copy or spread any parts of this document in any way without prior written allowance. All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown. Even though the WilTec Wildanger Technik GmbH has undergone the biggest possible efforts to ensure that the operating manual is complete, faultless, and up to date, mistakes cannot be entirely avoided. If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing from you.
Send an e-mail to: service@wiltec.info
or use our contact form: https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in our online shop via: https://www.wiltec.de/docsearch
Our postal address is: WilTec Wildanger Technik GmbH Königsbenden 12 52249 Eschweiler Germany
Do you wish to pick goods up? Our pick-up address is: WilTec Wildanger Technik GmbH Königsbenden 28 52249 Eschweiler Germany
To shorten the waiting time and allow for a rapid on-site transaction, we ask you to call us previously or place your order via the webshop.
E-mail: service@wiltec.info
Tel: +49 2403 555920
Fax: +49 2403 5559215
To return orders for exchange, repair, or other purposes, please use the following address. Attention! To allow for smooth execution of your complaint or return, it is important to contact our customer service team before returning the goods.
Returns Department WilTec Wildanger Technik GmbH Königsbenden 28 52249 Eschweiler
E-mail: service@wiltec.info
Tel: +49 2403 555920
Fax: +49 2403 5559215
© by WilTec Wildanger Technik GmbH http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
Item 60237, 60238

Introduction

Thank you for purchasing this quality product. To minimize the risk of injury we urge that our clients take some basic safety precautions when using this device. Please read the operation instructions carefully and make sure you have understood its content. Keep these operation instructions safe.

Product description

Workshop hanging cabinet:

two cabinets with doors
open cabinet with shelves
Perforated rear wall

Grey-black workbench:

large worktop
drawer
open compartment
cabinet with door

Parts list
Grey-black hanging cabinet

Assembly
We recommend the following tools for assembly (not included in the delivery):
At least 2 people should assemble the product. Note: Only use suitable tools for the assembly and regard all safety notes. Wear adequate working gear (slim-fitting tops, working trousers, gloves, work shoes, and if necessary protective glasses and respiratory protection).
Mounting the Hanging Cabinet
Step 1: Mounting the left side panel

Place the left side panel vertically and connect it to the back wall via the groove, so that both elements form a line.
Then turn the left side panel vertically inwards at a 90° angle. Ensure that the guide rail for the door is also facing inwards.

Step 2: Mounting the right-side panel (same procedure as step 1)

Place the right-side panel vertically and connect it to the back wall via the groove, so that both elements create one line.
Then turn the right-side panel vertically inwards at a 90° angle. Ensure that the guide rail for the door is also facing inwards.

Step 3: Mounting the front frame and cover panel

Mount the front frame with the tapping screws included in the delivery (fig. 3).
Place the cover panel on top of the back wall and the side panels. Ensure that the side with the 8 holes of the cover panel is facing upward (fig. 4).
Attach the two dividers in the centerpiece via the tapping screws (fig. 5).

Step 4: Mounting the doors

Place the lower door hinge into the hole in the rail. Then place a plastic washer on top of it (fig. 6b).
Place the door onto the lower hinge (fig. 6).
Then adjust the door, and ensure that the top hole of the door matches up with that of the cover panel.

Step 5: Mounting the wall fixtures

Mount the cabinet to the wall with the covering panel via the wall brackets (3 brackets) and tapping screws (3 screws) for later stabilization (3 nails for wall mounting included) (fig. 7).
Place the shelf boards in the middle section of the cabinet and fix them at the required height (fig. 8).

Mounting the workbench
Step 6: Mounting the side panels

Place the left side panel and connect it to the back wall via the groove, so that both elements form one line.
Then turn the left side panel vertically inwards at 90° angle. Ensure that the rails for the doors are facing inward as well. Repeat the procedure for the right-side panel (fig.9).
Mount the front frame with the tapping screws (fig. 10).

Step 7: Mounting the upper surface, floor, and dividers

Place the upper surface onto the side panels and the back wall. Use the tapping screws to attach it (fig. 11).
Turn the cabinet around to attach the floor (fig. 11). 3. Then push the divider slightly tilted into the cabinet. Place it vertically and fix it with the tapping screws (fig. 12).

Step 8: Mounting the doors

Place one of the lower door hinges into the pre-drilled hole of the bottom rail. A plastic washer needs to be placed on top of that (fig. 13b).
Place the door on the bottom hinge. 3. Then adjust the door, and ensure that the top hole of the door matches up with that of the cover panel. Then attach the upper door hinge (fig. 13).

Step 9: Mounting the legs

Place the furniture into its regular positioning again and place the metal frames on each side of the cabinet.
Attach the table legs with the included angled tapping screws (fig. 14).
Then attach the stands to the table legs (fig. 15).

Step 10: Mounting the drawers

First, connect the right and left side panels of the drawer with the bottom panel of the drawer and then lift it (fig. 16).
Then connect the front and back panel of the drawer via the tapping screws to the drawer (fig. 16).
Then place the metal rails on the right and left sides of the drawer (fig. 16).

Step 11: Mounting the worktop

Finally, mount the work surface onto the frame. On each side of the frame, there are three holes, which are used to connect the frame with the work surface via tapping screws.
The drawer can then be mounted beneath the work surface (fig. 17).

Cleaning and care

Clean the cabinet with a neutral cleaning detergent. Do not use any acidic or abrasive cleaning detergents or sponges. These might damage the cabinet.
Do not expose the cabinet to any weathering influences, as it can have a negative impact on the surface of the cabinet and its durability.
Clean the cabinet with a damp, soft cloth and wipe it afterward with a clean dry cloth.

Important notice:

The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction manual, require the written permission of WilTec Wildanger Technik GmbH.

© by WilTec Wildanger Technik GmbH
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de