GE current Z2P1500 UltraMax Connected LED Driver Installation Guide

GE current Z2P1500 UltraMax Connected LED Driver

WARNING

1. RISK OF ELECTRIC SHOCK
   •  Turn the power off before inspection, installation, or removal.
   •  Properly ground electrical enclosure.
2. RISK OF FIRE
   •  Follow all NEC and local codes
   •  Use only UL-approved wire for input/output connections.
   •  Minimum size 14 AWG for continuous runs.

Save These Instructions

Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-005(A)/NMB-005(A) Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Before installing this driver

1.  Remove power from LED luminaire by switching circuit breaker powering the LED luminaire to the off position. CAUTION: Turning off the LED luminaire’s wall switch may not remove voltage from the LED luminaire.
2.  For maximum safety, LED luminaire must be grounded. Make sure LED luminaire is properly grounded with a green ground wire per National Electrical Code (NEC).
3.  Verify that the LED driver is the correct LED driver for the LED luminaire, input voltage, and application.

During installation

1.  Follow all relevant National Electric Code (NEC), Federal, State and Local Electric Codes as well as U.L. safety standards.
2.  Access and open driver compartment cover.
3.  Remove old driver and any extra wires from the enclosure.
4.  Inspect and replace any damaged or deteriorated cable.
5.  Review the wiring diagram on the new driver label and identify connections to be made.
6.  Install the new LED driver and make sure the new LED driver is properly grounded to the metal of the LED luminaire per the National Electrical Code (NEC). Tighten driver mounting screws seating driver firmly against the LED luminaire surface. To ensure electrical grounding between the driver case and LED luminaire housing, mounting screws with star washers are recommended to break (penetrate) the painted surface of the driver mounting foot.
7.  Install the antenna within the LED luminaire enclosure (away from grounded metal surfaces when possible). The antenna shall not be cut or have any insulation material removed or tampered with in any way.
8.  Use only U.L.-approved wire connectors for all electrical connections. CAUTION: Wire connectors must be securely fastened and must completely cover exposed wire ends to prevent shock hazards.
9.  Be sure to insulate unused leads INDIVIDUALLY to 600Vrms using U.L. approved wire connectors.
10.  Verify that all installation and safety requirements have been completed and reinstall the driver cover.

After driver installation

Restore power at the circuit breaker, apply power to the fixture and ensure LED luminaire is operational

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference This device must accept any interference, including interference that may cause undesired operation of the device.

FCC Statment

This equipment (GED80MCC/Z2P1500) contains the limited module with FCC ID 2AS3F-80MCCZ2P15 and ISED ID 25008-80MCCZ2P15. This equipment complies with FCC CFR 47 Part 2 requirements for radiation exposure for the fixed facilities or mobile applications that maintain a distance of 20 cm from a person’s body. This equipment complies with ISED RSS102 Issue 5 requirements for radiation exposure limits for an uncontrolled environment that maintain a distance of 20 cm from a person’s body. This radio transmitter ISED ID 25008-80MCCZ2P15 has been approved by Innovation, Science, and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited from use with this device. Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• Suppliers Name: Current Lighting Solutions, LLC
• www.gecurrent.com

References

• LED Commercial Lighting and Lighting Controls | Current - GLI Brands

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>