Shenzhen P200 Wireless Mini Projector User Manual

Shenzhen P200 Wireless Mini Projector

Projector Brief Introduction

Appearance design

**Remote control introduction

**

• Bluetooth pairing mode
  Hold both “OK” and “Volume-” button five seconds to start remote control pairing mode

• Mouse mode
  Start: click mouse button
  Close: click navigation button

• Indicator light status
  Slow flash: unpaired mode
  Quick flash: enter pairing mode
  Flash: in infrared/Bluetooth mode press each button will flash once

Projector Using Guide

Power on Power off

1. Power on
   Hold down the first button on the back for three seconds, device on.(P1).

2. power off
   Hold down the first button on the back for three seconds, device off (P1) /Hold down the power button on the remote control to turn off.

Adjust focus /lightness

1. Adjust focus
   Hold down the button “FOCUS” to adjust focus, short press is for confirmation (P2).

2. Main interface focusing
   After entering the main interface, first click the middle circle of the top focus bar/ or press the remote control to enter the focus mode interface. Then press the top or bottom of the tracing bar to adjust the focus until the picture is clear and release your hand. Press the back button to exit the focus.

3. Adjust the brightness
   In the main interface, select “Settings” – “Projection Settings”- “LED Brightness”

Bluetooth controller pairing

Pairing method:
After entering the remote controller pairing page, hold both “OK” button and “volume- ” for seconds then lose and wait it till connect success.
Or: Enter into setting Bluetooth Setting, according to the tips to connect the Bluetooth controller or other Bluetooth device.

Connect Wi-Fi network

Operation of the main interface

Projection screen

Airplay iPhone

1. O In WiFi environment: Enter iPhone’s “Setting” “Wi-Fi”, then connect your phone to the same network with projectors, No WiFi environment:Enter iPhone’s “Setting”
   “Personal Hotspot”, Open “Hotspot”, then connect projector to it; Or enter the projector’s “Settings”- “Network Settings”-“Network Hotspot”, open the hotspot and connect iPhone to the hotspot;

2. Back toward the phone home page, slide up to open the control panel, then click Airplay

3. Choose “XX-XXXXX-XKX*”, then open “Mirroring and done.

Airplay Mac

1. Projector Networked: Click “”, Connect it to Projector through the same network.
2. Click” “, choose “XXX-XXXXXX-XXX” and be done

Miracast (Android Phone)

1. The machine opens and connects to WIFI, and enters the interface of “Android with the screen”

2. Open the WIFI of the Android phone.
   Under the phone “Settings – Display-Projection Screen”, search for and connect;

3. Most Android phones can be found and connected under the menu of “quick operation bar-screen sharing/screen mirroring/projection screen/WLAN display/wireless display/multi-screen interaction,or contact customer service.

Wired Mirror (iPhone / iPad)

1. Please connect the iphone and projector as shown (P3)
2. Click the”Trust” button on the phone (P4).

Other function

1. How to read the U disk contents
2. Connect USB OTG cable to Micro USB interface the of projector.
3. Connect U disk to the other side of USB OTG interface, the system will automatically pop up the file management interface.
4. How to connect Bluetooth speaker
5. Setting-Bluetooth Setting.
6. Open the Bluetooth speaker and enable Bluetooth pairing mode.
7. Click the scan search device on the projector interface.
8. The name of the corresponding Bluetooth speaker will be displayed in the available devices.
9. Click the connection to show that the Bluetooth speaker is connected.
10. How to use HDMI connection
11. Use the remote control or control panel to move to the top HDMI icon on the right side of the main interface to turn on the HDMI mode.
12. Click “Yes” to enter the black interface for debuggıng HDMI
13. The projector is connected to the HDMI cable on the computer for simultaneous display.

How to update firmware (local update) local update:

1. Download new firmware from the product website.
2. Copy the firmware file update. zip to the root directory of TF card.
3. Insert the TF card to the projector slot then the song one app will hint you to update the software.
4. Click update button to update.

Online upgrade:

1. Connect the device to the network;
2. Go to Settings-General-Online Update;
3. Click Install as prompted to perform the firmware update.

How to charge

• Plug the adapter to the Micro USB charging interface (P7).
• Solid red light indicates charging.
• Solid blue light indicates charging completed.

Product Reference

FCC Statement

This device comples with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2)
this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digtal device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructons, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. f this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the recelver is connected.
• Consult the dealer or an experienced radio-tv technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Radiation Exposure Statement
This device complies with RF radiation exposure limits set forth for an uncontrolled environment This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter This device must operate with a minimum distance of 20 cm between the radiator and user body.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>