TAIYO YUDEN EYSSSN Bluetooth Low Energy Module User Manual
- June 5, 2024
- TAIYO YUDEN
Table of Contents
User manual
(for EYSSSN)
FCC ID: RYYEYSSSN
IC Number: 4389B-EYSSSN
YUDEN EYSSSN Bluetooth Low Energy Module
Since this module is not sold to general end-users directly, there is no user
manual for the module. For the details about this module, please refer to the
specification sheet for the module.
This module should be installed in the host device according to the interface
specification (installation procedure).
The following information must be indicated on the host device of this module;
-
Japan Regulatory Information
a) This Product is a radio system and obtained certification of construction type combined with the specific antenna.
b) Please ensure that your product has a label with the following certification mark at the easily viewable location. If your product is too small to have the label, please place it in the instruction manual and package of your product. The mark diameter shall be equal to or greater than 3mm. In case your product does not have the label with the following certification mark, you or your customer who uses your product may be against the Radio Law and be subjected to criminal punishment. TAIYO YUDEN shall not be liable for any loss or damage incurred by you or your customer arising from the use of your product that does not have the following certification mark. This product has a radio system that was approved as a radio station in a low-power data communication system based on the Radio Law. EYSSSN: *********. -
Canada Regulatory Information
a) This device complies with Industry Canada’s applicable license-exempt RSS.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
b) This product is certified as a type of portable device with Industry Canada Rules. To maintain compliance with RF exposure requirements, please use within the specification of this product.
– IC: 4389B-EYSSSN
c) Please notify certified ID by either one of the following methods on your product.
– Contains IC: 4389B-EYSSSN
– Specifiez ID certifiée dans votre produit par une de méthode suivante.
– Contains IC: 4389B-EYSSSN Specifiez ID certifiée dans votre produit par une de méthode suivante.
– Contains IC: 4389B-EYSSS -
FCC Regulatory Information
a) This device complies with part 15 of the FCC Rules.
– Part 15 Subpart C
b) Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
c) Please notify certified ID by either one of the following methods on your product.
– Contains Transmitter Module FCC ID: RYYEYSSSN
– Contains FCC ID: RYYEYSSSN
d) Since there is no space that indicates FCC ID on this module, FCC ID is indicated in a manual. If the FCC ID is not visible when the module is installed inside another device, then the module is installed must also display a label referring to the enclosed module.
e) CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
f) The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
g) This product is certified as type of portable device with FCC Rules. To maintain compliance with RF exposure requirements, please use within the specification of this product.
h) The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
i) This module can change the output power depending on the circumstances by the application software which is developed by the module installer. Any end- user cannot change the output power. The test software is developed by TAIYO YUDEN, and during regulatory testing, the output power is set to maximum power.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CE Regulatory Information
a) When your end product installs this module, it is required to proceed with
additional certification processes before placing on the market in EU member
states to make your products fully comply with relative EU standards.
b) TAIYO YUDEN can provide you the test reports of conducted measurement
portion for the radio module. You can utilize the test reports for the
certification processes of your end product as it requires radio testing.
TAIYO YUDEN CO., LTD.
Documents / Resources
|
TAIYO YUDEN EYSSSN Bluetooth Low Energy
Module
[pdf] User Manual
EYSSSN, RYYEYSSSN, Bluetooth Low Energy Module, EYSSSN Bluetooth Low Energy
Module
---|---