Shenzhen GD8205 Digital Wireless Baby Monitor User Manual

: June 5, 2024
: Shenzhen

Table of Contents

Introduction
Parts in the package
Icon Description
Using the Monitor
Preparation before using the camera
Access receiver menu
Feeding timer
Version information
Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GD8205 Digital Wireless Baby Monitor
User Manual Shenzhen GD8205 Digital Wireless Baby
Monitor

Model No.: E3205KG
Version 1.0
Please read this user manual carefully before using this product. Failure to understand operation procedures may result in injury.

Introduction

Thank you for choosing our baby monitor. Please read the instruction carefully in case of
product damage due to improper operation.

Parts in the package

Shenzhen GD8205 Digital Wireless Baby Monitor -
package Product structure

Shenzhen GD8205 Digital Wireless Baby Monitor - Product
structure

1.camera sensor
2.Lens
3.Microphone
5.SET
4.Indicator LED6.Temperature sensor
7. DC power interface

Shenzhen GD8205 Digital Wireless Baby Monitor - Product structure
1

08. Antenna
09. Menu button/Return
10. Power on/off button
11. Lullabies button
12. Turn UP/ Brightness+| 13. Confirmation button/Zoom button
14. Turn right/Volume+
15. Turn down/Brightness
16. Turn left/Volume
17. Dialogue key —-> Talking Key| 1 8. Status indicator
19. Microphone
20. Shortcut button
21. RESET button
22. DC power interface

---|---|---

Icon Description

Status Bar Icon

| No signal connection between the receiver and the camera
---|---
| Signal strength between the receiver and the camera
| The Lullaby function is enabled.
27°C| Displaying current room temperature
| Indicating the current battery level. When the battery is too low, this icon will change to and flash.
| The temperature alarm is enabled

Message push icon
****No camera is added or the camera is disconnected from the receiver
Temperature alarm

The explanation for the status indicator LED

The first green indicator is steady indicating a successful connection between the camera and the receiver.
The first to the fifth green indicator slowly flashes simultaneously: indicating power on, but the camera not connected.
The second to the fifth green indicators slowly flash from low to high: indicating the received volume
The second to the fifth green indicators slowly flash simultaneously: indicating that the alarm signal is received.
The sixth red indicator is steady on indicating that the lithium battery is being charged; (displayed whether it is turned on or off)
The sixth red indicator is off: indicating that the battery is fully charged.

Using the Monitor

Place the Camera Unit in a convenient location (e.g. on a table or a shelf) and point the camera lens toward the area you want to monitor.
Shenzhen GD8205 Digital Wireless Baby Monitor - Product structure
2

NOTE:
Do not place the Monitor Unit within the baby’s reach. If there is interference with the picture or sound, try moving the units to different locations, and ensure they are not close to other electrical equipment.

WARNING
Strangulation Hazard:

Children have STRANGLED in cords.
Keep this cord out of the reach of children (more than 3 feet (0.9m) away). Never use extension cords with AC Adapters. Only use the AC Adapters provided.

Preparation before using the camera

1. Powering the Camera Unit
Shenzhen GD8205 Digital Wireless Baby Monitor -
Powering Insert one end of the included charging cable into the USB jack on the back of the camera.
Insert the other end into the included power adapter. Then insert the adapter into the socket.

Shenzhen GD8205 Digital Wireless Baby Monitor - socket After being powered on, the camera will automatically turn on. (The green light on the base of the camera is on for a few seconds. At this point, the camera is turned on successfully).

Preparation before using the receiver

Power on the receiver (The receiver is provided with a lithium battery, if the receiver has enough power, please go directly to the Step 2).
Insert one end of the charging cable into the USB charging jack on the side of the receiver.
Insert the other end into the included power adapter. Then insert the adapter into the socket.
Receiver starting up
Press and hold the button on the receiver to start the receiver

At this point, a monitor screen will appear on the receiver.
Note: This device has been paired before leaving the factory. If the receiver fails to display on the monitor screen as described above, please re-try the device pairing operation. For detailed steps, please refer to Page 9 “Camera Pairing”.
Receiver function settings
The functions of the Babysitter are user-definable, to best satisfy your demands. Audio and temperature alarms may offer automatic notification to you. This chapter will introduce the user-definable settings item by item.

In states of live view, pressing the MENU button on the monitor can enter into the MENU list; In states of non-live view, pressing the MENU button on the monitor can return to the previous interface level. Shenzhen GD8205 Digital
Wireless Baby Monitor - fig 1

Camera settings (camera pairing and deletion)
Add camera

Select Icon and press OK to enter.
Select the channel to be paired, press OK to confirm, select and press OK to confirm.
When the device prompts “camera is No paired”, press OK to confirm.
When the device prompts “Start pairing, please short press the camera SET key”, press the SET key of the camera shortly to enter the pairing mode.”
When the device prompts “Pairing is Ok”, which indicates that the device is successfully paired, the menu will skip to the real-time monitoring menu, and the first indicator light of the receiver is constantly on in green.

Shenzhen GD8205 Digital Wireless Baby Monitor - fig 6

Delete the camera

Select Icon and press OK to enter.
Select the channel to be deleted, press OK to confirm, select and press OK to confirm.
When the device prompts “Camera is paired. Can be deleted” Press OK to confirm. When the device prompts “Deleting is OK”, the camera is successfully deleted.

Shenzhen GD8205 Digital Wireless Baby Monitor - fig 8

Audio alarm settings
Set the range of the sound sensitivity alarm. Set the sound sensitivity alarm range. This function recognizes the intensity of the baby’s crying, and when the value is above the threshold, the receiver will sound an alarm.

Select the icon and press OK to confirm
Select the 、、 icon as needed and press OK to confirm.

The audible alarm setting is completed. Press MENU to return. Shenzhen GD8205
Digital Wireless Baby Monitor - fig 5

Note: The audible alarm will last for 1 minute. The audible alarm notification can be switched off by pressing any button on the receiver, and the notification will not be received again within 3 minutes thereafter.
Temperature alarm settings
The temperature alarm gives a push notification to your receiver when your baby’s room is too hot or too cold.

Select and press OK to enter the setting page

Celsius setting
Set to Celsius: Select a °c press OK to confirm.
Temperature switch: Select ON and press OK to confirm

After setting, press MENU to return. Shenzhen GD8205 Digital Wireless Baby
Monitor - fig 11

Fahrenheit setting
Set to Celsius: Select °F and press OK to confirm.
Temperature switch: Select ON and press OK to confirm
After setting, press MENU to return. Shenzhen GD8205 Digital Wireless Baby
Monitor - fig 13

Note: The setting of the temperature alarm defaults to 15~29°C (59°F~84°F). When the baby’s room temperature is outside this range, the receiver will receive a temperature alarm. The audible alarm will last for 1 minute. The audible alarm notification can be switched off by pressing any button on the receiver, and the notification will not be received again within 3 minutes thereafter.

Feeding timer

You can set the receiver to auto-feeding timer mode. This setting will automatically switch to sleep mode depending on the length of such setting.

Select and press OK to enter the setting page.
Select the length of sleep as needed. Press OK to confirm. At this point, the receiver will automatically sleep according to the time setting. After the setting is completed, press MENU to return.

Shenzhen GD8205 Digital Wireless Baby Monitor - fig 9

Lullabies
The babysitter has 5 pieces of lullabies to help you sleep your baby.

Select the ****icon and press OK to enter the setting page.
Select the music you want to play, press OK to confirm, and the camera will play the selected lullaby, press OK again to pause the lullaby. Select “All” to play all the lullabies in a loop. When the setup is complete, press MENU to return.

Shenzhen GD8205 Digital Wireless Baby Monitor - fig 10

Note: In this screen, press to switch the lullaby and press to adjust the volume.

Setting
This setting includes time settings, factory reset, and viewing hardware version
Time setting
Calibrate the time on the receiver.

Select and press OK to enter the setting page.
Select and press OK to enter the setting page.

Shenzhen GD8205 Digital Wireless Baby Monitor - fig 14

3. You may press to select the item to be adjusted; press to edit the selected item. After the setting is completed, press OK to confirm. Press MENU to return. Shenzhen GD8205 Digital Wireless Baby Monitor - fig
15

Language setting
Switch language displayed on the receiver.

Select Settings, and press OK to enter the settings page.
Select Language Settings, and press OK to enter the settings page. Select a language you need and press OK to confirm.

Reset default settings
Format all settings on the receiver and delete the camera.

Select and press OK to enter the setting page.
Select and press OK to enter the setting page.
At this time, the device will prompt “Restore to default settings?”. Select YES and press OK to confirm. The device will start resetting to default settings
After the default settings are restored, the receiver will automatically switch to the monitoring interface with an icon indicating that no camera is added.

Version information

View the version information of the receiver

Select and press OK to enter the setting page.
Select and press OK to enter .
The receiver will display the corresponding version information. Press MENU to return after reviewing the version information.

Specifications

Camera

All the specifications are subject to minor change without prior notice.
CE and FCC Certification Information
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information:
FCC RF Exposure requirements: The highest 1g SAR value reported under this standard during product certification for use body exposure condition with the minimum separation distance of 0mm is 0.02W/Kg. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter. This product is in compliance with FCC RF exposure requirements and refers to the FCC website https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm search for FCC ID: TW5GD7605
This equipment complies with radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator& your body. This product is in compliance with FCC RF exposure requirements and refers to the FCC website https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm Search for FCC ID: TW5GD8205
Hereby, we declare that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
Notice: Observe the national local regulations in the location where the device Is to be used. This device may be restricted for use in some or all member states of the European Union (EU)

EU Environmental Provisions
E-waste cannot be mixed with household garbage; the corresponding local government sector or recycling stations shall be responsible for the circular process.