SONGNORMI SN-TS10-10 TWS Wireless Bluetooth Earbuds User Manual
- June 5, 2024
- SONGNORMI
Table of Contents
SONGNORMI SN-TS10-10 TWS Wireless Bluetooth Earbuds
Product parameters
- Model: TS10
- Bluetooth version: V5.0
- Transmission frequency: 2.402G-2.480G
- Connection distance: ≧10M
- Supporting protocols: HSP, HFP, A2DP, AVRCP
- Music playing time: 6-7H
- Standby time: about 180H
- Headphone battery capacity: 3.7V 50mAh
- Charging battery capacity: 3.7V 800mAh
- Charging input: 5V 500mA
- Charging time: 2-3H
- Working environment: -10 ° C -50 ° C
Power on & Pairing
- Take out the left and right earbuds from the charging case at the same time, the earbuds will automatically turn on (or press the multi-function key for 3S at the same time). The earbuds will light blue after turn on.
- After turn on, the left and right earbuds automatically enter into pairing mode. After paired successful, the main earbud red and blue lights flash alternately, and the auxiliary earbud light turn off.
- Turn on the Bluetooth on mobile phone, search for the Bluetooth device pairing name: TS10, click the name to connect (if need password: please enter “0000”), the indicator will be off after connected successfully.
Power off
- During using, put the left and right earbuds back into the charging case to shut down, or press any earbuds multi-function keys until the red light on , then release and the earbuds shut down.
- The earbuds will be power off automatically if the earbuds far from the device or not pairing with any device for 5 minutes.
Use again
- Take out the single earbud or both earbuds from the charging case, and the earbud will automatically connect back to the last connected device.
- If the earbudt is in the off state or not in the charging compartment, put the earbud into the charging caset to activate it and then remove it, or press and hold the headset multifunction key to turn it on, the earbud will automatically connect back with the mobile phone.
Charging
- Charge the earbuds: Put the headset into the charging case ad close the case to start charging. The screen LED flashes in sequence. 25% power per grid, four grids light on when earbuds in full charging.
- When charge the charging case: the screen displays the real power. When fully charged, the screen displays 100%.
- Charging the charging case: Insert the type C cable to charge the case.During charge, the screen displays the real power. When fully charged, the screen displays 100%
Button function operation
- Click the L/R ear: answer/hang up the phone,
- play/pause
- Double click L: last song
- Double click R:next song
- Three click L : volume –
- Three click R : volume +
- Long press L/R for 2S: wake up Siri function (only support IOS system and parts Android system)
- Long press L/R for 3S: power on
- Long press L/R for 5S: power off
prompt
- Please read the instruction manual carefully before using this product.
- Please fully charged this product for first time using.
- If the product have not used for a long time (more than 15 days), please charge it.
- Must select a charger that is produced by a regular manufacturer which has CCC certificate.
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>