Dongguan Fulun Electronics B96 Jack Bluetooth Speaker and Wireless Charging Pad Instruction Manual
- June 5, 2024
- Dongguan Fulun Electronics
Table of Contents
Dongguan Fulun Electronics B96 Jack Bluetooth Speaker and Wireless
Charging Pad
B96
Functions
- Wireless Charging Pad
- Micro USB Port
- LED Indicator
- ON/OFF Switch
What’s included:
1 x Bluetooth® Speaker (7198-50)
1 x USB to Micro-USB Charging Cable 1 x Instruction Manual
Tech Specifications
- Playing time: up to 2.5 hrs at max volume
- Charging time: up to 2 hrs
- Pairing Name: “Jack BT”
Instructions
(Be sure to fully charge the speaker before using for the first time).
-
Charging the Speaker
Connect the provided charging cable to a power source and to the micro USB port on the speaker (3).
The LED indicator light will glow red when charging and turn off when fully charged. -
Bluetooth® Setup:
Turn-ON/OFF switch to the ON position, LED Indicator will flash BLUE.
Turn on the Bluetooth function on mobile device, Select “Jack BT” pairing name. LED will glow BLUE if successfully paired Speaker will automatically pair if the mobile device has been paired before.
Press and hold ON/OFF button to turn off the device -
Wireless Charging:
Connect the provided charging cable to a power source, place wireless charging supported mobile device on top charging pad.
The device will begin to charge automatically
SAFETY PRECAUTIONS
WARNING- When using this product, basic precautions should always be followed:
- Read all the instructions before use.
- Never store or use this product in temperatures below 32°F(0°C) or above 115°F(45°C).
- Do not overcharge Phone. Unit may get hot with excessive use. Remove the Phone when it is fully charged. Never charge for more than 7 hours at a time.
- The unit’s full performance is achieved only after 2 or 3 completed charge and discharge cycles.
- To reduce the risk of injury, close supervision is necessary when the product is used near children.
- Do not expose the device to moisture. Do not use the device in excess of its output rating.
- Overload outputs above rating may result in a risk of fire or injury.
- Do not use the device if damaged or modified.
- Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
- Do not disassemble the device. For repairs, seek a qualified service professional. Incorrect reassembly may result in a risk of fire or injury.
- Do not expose the device to fire or excessive temperature. Exposure to fire or temperatures above 104°F may cause explosion.
- Ensure that qualified service professionals use only identical replacement parts to ensure product safety
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment general uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures: Reorient
or relocate the receiving antenna. Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1) this device may not cause harmful
interference, and (2)this device must accept any interference received,
including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.