VIOMI V3 Robot Vacuum Cleaner User Manual

VIOMI V3 Robot Vacuum Cleaner

Safety Information

Usage Restrictions

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision (EU).
• Please keep the main brush cleaning tools out of reach of children.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Do not use the vacuum-mop to clean any burning substances.
• Do not pick up the vacuum-mop by its laser radar cover.
• Make sure the vacuum-mop is turned off and the charging dock is unplugged before cleaning or performing maintenance.
• This vacuum-mop is only intended to clean floors in a home environment. Please do not use it outdoors such as on an open balcony or on a surface that is not a floor like a sofa, or in a commercial or industrial setting.
• Do not use the vacuum-mop in an area suspended above ground level, such as a loft, open balcony, or on top of furniture, unless a protective barrier is present.
• Do not use the vacuum-mop at an ambient temperature above 40°C or below 0°C or on a floor with liquids or sticky substances.
• Pick up any cables from the floor before using the vacuum-mop to prevent it from dragging them while cleaning.
• Pick up any fragile or loose items from the floor, such as vases or plastic bags, to prevent the vacuum-mop from being obstructed or bumping into them and causing damage.
• Do not place children, pets, or any item on top of the vacuum-mop while it is stationary or moving.
• Do not use the vacuum-mop to clean the carpet.
• Do not allow the vacuum-mop to pick up hard or sharp objects such as building materials, glass, or nails.
• Do not spray any liquid into the vacuum-mop (make sure the dust compartment is thoroughly dry before its reinstalling).
• Do not place the vacuum-mop upside down (laser radar housing should never touch the ground).
• Only use this product as directed in the user manual or quick start guide. Users are responsible for any loss or damage arising from improper use of this product.

Batteries and Charging

• Do not use any third-party battery, charger, or charging dock. Use only with supply unit.
• The appliance must be disconnected from the supply mains when removing the battery.
• This appliance contains batteries that are only replaceable by skilled persons.
• Do not place the charging dock near a heat source, such as a radiator.
• Do not wipe any part ofthe vacuum-mopwith a wet cloth or other liquid.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or qualified persons in order to avoid a hazard.
• Do not improperly dispose of old batteries. Before discarding the vacuum-mop, make sure the vacuum-mop is unplugged and the battery must be removed and disposed of in an environmentally safe manner.
• Make sure the vacuum-mop is turned off when being transported and kept in its original packaging if possible.
• If the vacuum-mop will not be used for an extended period, fully charge it, then turn it off and store it in a cool, dry place. Recharge the vacuum-mop at least once a month to prevent battery damage.

This product’s laser radar meets the IEC 60825-1:2014 Standard for Class 1 laser product safety and does not produce laser radiation hazardous to the human body.

Electrical Diagram

Product Overview

Product & Accessories List

Vacuum-Mop Accessories

Accessory Box Contents

Note: Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.

Dock

Press to send vacuum-mop back to charging dock.

Power/Cleanup Button

Press to start or pause cleaning. Press and hold for 3 seconds to turn the vacuum mop on or off.

Indicator Status

Installation

1. Connect the charging dock to the power outlet.
2. Install the side brush on the upper-left corner of the vacuum mop, as shown in the figure. An extra side brush in the package is provided as a spare and does not need to be installed.
3. Place the charging dock on a level ground against a wall.
4. When using the vacuum mop for the first time, press and hold the button (‘.) for 3 seconds to turn on the vacuum mop. Once the indicator lights up, manually place the vacuum mop onto the charging dock to charge. Then just press the button O when the vacuum mop is cleaning, it will automatically go to the charging dock to recharge. Blue: Turned on/Working normally/Fully charged/Wi-Fi Connected Breathing yellow: Charging Blinking red: Error

Installing Accessories for Desired Mode
Cleanup mode: Install a 2-in-1 dust compartment with a water reservoir.

1. Open the cover of the vacuum-mop and place 2-in-1 dust compart­ment with a water reservoir in the direction shown until it locks into place.
2. Turn on the vacuum mop. It is now ready to start cleaning.

Vacuuming and mopping mode: Install a 2-in-1 dust compartment with water reservoir, mop holder, and mop.

1. Open the water reservoir lid, fill up the reservoir, then reattach the lid.
2. Install the 2-in-1 dust compartment with water reservoir into the vacuum mop until it locks into place.
3. Attach the mop to the holder and press the velcro strips firmly together.
4. Pinch the clips, and install the mop holder horizontally into the bottom of the vacuum mop, as illustrated.
5. Turn on the vacuum mop. It is now ready to start vacuuming and mopping.

Precautions:

1. Do not place the charging dock in an area with direct sunlight.
2. Make sure there are 0.5 meters or more of open space on either side of the charging dock and more than 1.5 meters in front.
3. If the vacuum-mop is unable to turn on due to low battery, place it directly onto the charging dock to recharge.
4. The vacuum-mop will automatically turn on when it is on the charging dock.
5. The vacuum-mop cannot be turned off when it is on the charging dock.
6. Remove 2-in-1 dust compartment with water reservoir and mop holder when the vacuum mop is charging or not in use.
7. Use the virtual wall or set restricted areas for carpeted areas to prevent the vacuum mop from getting caught on the carpet.
8. Regularly clean the 2-in-1 dust compartment to prevent excess dirt accumulation. This can avoid reducing the cleaning performance of the vacuum mop.

How to Use

Turning On/Off
When the vacuum mop is on the charging dock, it will automatically turn on and cannot be turned off.
To manually turn on the vacuum mop, press and hold the button() until the indicator lights up. When the vacuum-mop is in standby mode and not on the charging dock, press and hold the button () to turn it off.
Cleaning
Turn the vacuum mop on, then press the button () . Depending on the accessory installed, the vacuum-mop will automatically begin vacuuming or mopping.
Recharging
Turn the vacuum mop on, then press the button O to send the vacuum mop to the dock to recharge.
When the vacuum-mop completes the cleaning task, it will automatically return to the dock for recharging, and the indicator is blinking yellow.
If the vacuum-mop starts running low battery during a cleaning task, it will automatically return to the charging dock to recharge. Once the vacuum mop is fully charged, it will resume cleanup where it left off.
If the vacuum-mop automatically shuts down due to low battery, manually place it onto the charging dock, and make sure the charging terminals have a good contact.
Pausing
While the vacuum mop is running, press any button to pause it, then press the button () to resume cleaning. Pressing the button O will end the current cleaning task and send the vacuum mop back to the charging dock.
Sleep Mode
The vacuum-mop will automatically enter sleep mode after 5 minutes of inactivity. To wake it up, press any button or use the app.

• The vacuum-mop will not enter sleep mode while on the charging dock.
• The vacuum-mop will automatically turn off after being in sleep mode for 12 hours.

Fault Status
If the vacuum-mop encounters an error during operation, the indicator will blink red and you will hear a voice alert. To check for a solution, please refer to the Troubleshooting section. If no action is taken within 5 minutes, the vacuum-mop will automatically enter sleep mode.
Adding Water or Cleaning Mop During Cleaning
If you need to add more water to the vacuum-mop or clean the mop during a cleaning task, press any button to pause the vacuum-mop, then remove the water reservoir. After adding water or cleaning the mop, reinstall the water reservoir and mop, then press the button () to resume the cleaning task.

Cleaning Preferences
Four suction modes are available in the Mi Home/Xiaomi Home app: Silent, Standard, Medium, and Turbo. The default mode is Standard.
Do Not Disturb Mode
In the Do Not Disturb mode, the vacuum-mop will not resume cleanup, perform scheduled cleanup, or issue voice alerts. Do Not Disturb Mode is enabled by default and can be disabled via the app.
Resuming Cleanup
The vacuum-mop has a feature of resuming cleanup. If the vacuum-mop starts running low battery during a cleaning task, it will automatically return to the charging dock to recharge. Once the vacuum-mop is fully charged, it will resume cleanup where it left off. If the cleaning task is manually ended while the vacuum-mop is charging, cleanup will not be resumed.
Zoned Area
You can use the app to set up the zoned area, then the vacuum-mop will clean up within the zoned area you selected.
Clean There
You can set a specified area on the map via the app, then the vacuum-mop will automatically navigate to the area and clean a square-shaped area of 2 • 2 meters.
Scheduled Cleanup
You can schedule cleaning times in the app. The vacuum-mop will automatically start cleaning at the scheduled times, then return to the charging dock after the cleaning is completed. Note: The vacuum-mop will not do the scheduled cleanup during the Do Not Disturb period if Do Not Disturb mode is enabled.
Virtual Walls/Restricted Areas
You can set up virtual walls and restricted areas in the app to prevent the vacuum-mop from entering areas you wish not to clean.
Smart Mapping
You can use the app to enable smart mapping. This allows the vacuum-mop to automatically update its map after completing a cleaning task and recharging.

Connect with Mi Home/Xiaomi Home App

This product works with Mi Home/Xiaomi Home app *. Control your device, and interact it and other smart home devices with Mi Home/Xiaomi Home app. Scan the QR code to download and install the app. You will be directed to the connection setup page if the app is installed already. Or search “Mi Home/Xiaomi Home” in the app Store to download and install it. Open Mi Home/Xiaomi Home app, tap “+” on the upper right, and then follow prompts to add your device.

• The app is referred to as Xiaomi Home app in Europe (except for Russia). The name of the app displayed on your device should be taken as the default.
  Note:
  The version of the app might have been updated, please follow the instructions based on the current app version.
  Resetting Wi-Fi
  When switching to a new router or changing your Wi-Fi password, you will need to reset the vacuum-mop’s Wi-Fi connection. Turn on the vacuum mop, then simultaneously press and hold the buttons O and C) for 3 seconds until you hear a voice saying “Waiting for the network configuration”. Once the Wi-Fi connection is successfully reset, you can reconnect the vacuum-mop.
  Note: Only 2.4 GHz Wi-Fi networks are supported.
  Restoring Factory Settings
  Press and hold the button O for 5 seconds. When you hear a voice saying “Factory settings will be restored”, press and hold the button O again for 5 seconds until it says “Restoring factory settings”. When the settings are successfully restored, all user data will be cleared, and you will hear a voice saying “Factory settings restored successfully”.

Care & Maintenance

2-in-1 Dust Compartment with Water Reservoir

1. Open the cover of vacuum-mop, remove the 2-in-1 dust compartment with water reservoir, then remove the filter as shown in the figure.
2. Empty the contents of the dust compartment. Clean the compartment using the cleaning brush, then align and reinstall the filter.
3. Reinstall the 2-in-1 dust compartment with water reservoir into the vacuum-mop until it clicks into place, then close the cover of the vacuum-mop.

Filter

To clean the filter in 2-in-1 dust compartment with water reservoir, remove it as indicated in the diagram.

• After rinsing the filter with water, make sure it is thoroughly dry when reinstalling the filter into 2-in-1 dust compartment with water reservoir.
• To prevent the filter from becoming clogged, it is recommended to regularly clean the filter using the cleaning brush.
• It is recommended to replace the filter every 3 to 6 months.

Main Brush

1. Flip the vacuum-mop over and pinch the clips to remove the main brush guard.
2. Remove the main brush and the main brush bearing.
3. Use the cleaning brush to clean the main brush.
4. Reinstall the main brush and its bearing, then put back and press down the main brush guard until it locks into place.

Note: It is recommended to replace the main brush every 6-12 months for optimal cleaning effectiveness.

Side Brush
Periodically remove and clean the side brush. It is recommended to replace the side brush every 3-6 months for optimal cleaning effectiveness.

Cliff Sensors
Clean the cliff sensors every three months using a soft cloth.

FAQ

Troubleshooting

Specifications

Vacuum-Mop

Charging Dock

Power Adapter

Documents / Resources

| VIOMI V3 Robot Vacuum Cleaner [pdf] User Manual
V3, Robot Vacuum Cleaner
---|---
| Viomi V3 Robot Vacuum Cleaner [pdf] Instruction Manual
V3 Robot Vacuum Cleaner, V3, Robot Vacuum Cleaner, Vacuum Cleaner, Cleaner

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>