ERAARK B09MQDW2VV Smart Fish Tank User Manual

ERAARK B09MQDW2VV Smart Fish Tank User Manual

I A MESSAGE TO OUR VALUED CUSTOMERS

• Thank you for choosing ERAARK Smart Fish Tank Pro. We at PETKIT have done our best to make life easier for you and your pets with technology.
• Please carefully read the User Manual before using the product. By setting up and using this product, you are acknowledged that you have already read and accepted the safety guidelines listed below.
• We are not liable and will not accept responsibility for any accidents or injuries that result from improper use of this product.
• PETKIT reserves the rights of interpretation and revision.
• This product supports Bluetooth protocols for Bluetooth 4.2 and above. It does not support Wi-fi.
• This device supports i0S9.0 and above, as well as Android 5.0 and above.

I USER SAFETY GUIDE

” Failure to follow the safety guides outlined below can result in product malfunction or other unforeseen mishaps.

• Please install and use the product as instructed in the User Manual.
• Only use the provided Power Adapter. Using a different power adapter may result in damages to the product and potential safety hazards.
• When installing, performing maintenance, or cleaning this device, please make sure to first turn off the power. After cleaning, make sure to reinstall each component part properly before turning the power back on. Once the power is back on, make sure the filtration system is functioning properly.
• Do not rinse the lid with water directly as it contains electrical parts in there. To prevent short circuits and damages, use a towel to clean the lid only. • It is forbidden to scratch or impact the tank with sharp objects to prevent scratches or damage on the surface.
• To prevent scratching or deforming the lid and the tank, do not set other objects on top of the lid or on top of the tank.
• When plugging in or unplugging the power cord, make sure your hands and the plug are dry. Never attempt to plug in or unplug the power cord if your hands are wet.
• It is recommended to add water according to the range indicated by the water level line on the fish tank.
• Please place the power adapter of the fish tank out of the reach of children.
• Please make sure the device is placed on a level surface. • Do not attempt to move or slide the tank once it has been filled with water. This may result in the tank breaking or deforming.
• If you encounter any problems while using this product, please contact us immediately.

CONTENTS OF PACKAGING

• Before setting up your device, please make sure you have all the necessary parts.

PRODUCT DESCRIPTION

HOW TO USE

1. nta k Rtegulating Valve Rotate the cap of we air replacing valve counterclockwise to increase the oxygen in the fish tank. (Do not rotate the cover completely.)

2. Lighting and Button 1. Light plate: Lift up the light plate and the lights will turn on. Press down the light plate, and the lights will turn off.

3.  Circular touch face-plate: By sliding clockwise or counterclockwise, you can adjust the lighting effect. Note: You can access more specific lighting controls and information via the Ap

4. Touch control button: Double press: Turn the water pump on and off. Single press: Turn the light on and off.|

Using the app

1. Please download PETKIT App from App store or Android App Market. Go in the app tap “+” to add devices and link the devices accordingly. Go to the App’s main page and follow the instructions to add your ERAARK Smart Fish Tank Pro and connect your device.

2. Under the white light mode, you can open tracking light mode in the App. The tracking light mode can be automatically terminated by pressing the key to switch the light. (Tracking light mode: it can intelligently simulate the changes of natural light according to time and location.)

3. Through the App, you can adjust the brightness of the lighting, set scheduled tasks, switch child lock, and turn sound on or off, among other things. * This product supports Bluctooth connectivity. The App can only control the device once a Bluetooth connection has been established.

I MAINTENANCE AND CLEANING

1. You will need to thoroughly wash the glass tank before filling it for the first time. Remove any residue or other material that may be left over from the manufacturing process. Cleaning supplies must be cleaned and disinfected to ensure cleanliness.
2. To ensure the quality of the water remains stable, we recommend changing the water in the tank once a week, and not changing more than a third of the tank’s full capacity each time.
3. Do not use chemical reagents, cleaning solutions, or water above 40 degrees Celsius when cleaning the glass tank.
4. Cleaning the glass tank: Before cleaning the glass tank, scan the QR code to watch an instructional video on how to clean the tank.
   This will help you avoid any accidents. • 1 he physical liter element should be cleaned every 2 week and replaced every 2 mont-s.

• When attaching the water pump power cord interface, remember that the internal plug of the power cord should be aligned, and then rotate the interface to the most tight position, and then install the cord back into its corresponding hole to restore its service state.

FAQ

1. The button is not working? ED Check to see if there is water on the touch control button. If there is, wipe it dry and try again. ® Using the App, you can set a child lock for the control button. When the child lock is on, lock the button on the device will not respond while being pressed. You can check if the child is on or off by using the App.
2. How to use tracking light mode? In the App, go to the main page for your device. After choosing white light mode, you can turn the tracking light mode on or off. Once tracking light mode is turned on, the device will automatically adjust the tone and brightness of light in the tank based on the time and the seasons of the location where you are using the tank, simulating changes in the natural environment, and simplifying user operations. In the device settings page of app, enter the device location page to update the device location. After updating the device location, the configuration of the tracking light mode will be automatically updated.
3. The water turned murky on the second or third day after adding in fish. Reasons for murky water and how to fix the problem: CD The reason the water in the tank turns murky on the second or third day is that the nitration system has not been established yet. When there is no fish, there will be no dirty things in the tank, so the water is clear. When there are fish, microbes are introduced as well, and those affect the quality of the water. At this point, the nitration system has not yet started taking effect. This is a necessary step when first adding fish into the tank. ® Users can change 3/4 of the water in the tank on the third day of murky water or introduce nitrifying bacteria to quickly establish the nitration system in the tank. ® Over longer periods of use, users should check to see if the filter sponge is in need of cleaning once a week, and replace or clean the filter sponge according to its dirty degree. ® Every two weeks, check to see if the water is becoming murky, and if it is, to choose whether to change water.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and ; (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC warning:

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radiofTV technician for help.
The device has been evaluated to meet general RF exposure requirement.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

IC warning

– English: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>