XPOtool 34223 Extension Hose for Extraction Unit User Manual
- June 5, 2024
- XPOtool
Table of Contents
XPOtool 34223 Extension Hose for Extraction Unit User Manual
Introduction
Thank you for choosing to purchase this quality product. To minimize the risk of injury, we ask you to always take some basic safety precautions when using this product. Please read this operating manual carefully and make sure that you understand it. Keep these operation instructions in a safe place.
The extension tube E420H is compatible with the chamber E420. Combining these two matching elements, you will achieve optimal results. Not only the paint mist is filtered, but also harmful vapors are led outside through the HS E420H tube. Thus, the air inside the work zone will be kept clean and fresh.
Features
- Lightweight, easy to assemble and disassemble
- The length of the hose can be varied from 0.7 to 1.7 m.
- The long flat exhaust piece can be pressed to 25 mm from both sides, so that it fits in a window or door gap.
Parts
-
Plastic sleeve
-
Soft threaded sleeve
-
Hose clamp
-
Extension tube
-
Exhaust piece
Connection
CAUTION
-
When using the extension tube, take out a filter-net layer from the device. There are two layers of filter mesh in the spray booth, only one of which is needed when using the extension tube.
-
Unscrew the 4 screws from the protective grille on the back of the HS-E420 spray booth (see fig. 1).
-
Use the 4 screws unscrewed in the previous step to connect the plastic sleeve to (19) with the HS E420 spray booth (see fig. 2).
-
Screw the soft threaded sleeve (20) and extension hose (22) together and connect the extension tube to the exhaust piece (23) (see fig. 3).
-
Place the hose clamp (21) onto the soft threaded sleeve (20) and screw it into the plastic sleeve (19) (see fig. 4).
-
Extend the hose as you wish and place its exhaust piece outwards through a window or door gap **(see fig. 5)
**
You can also fix the hose by attaching the plastic sleeve to the ventilation
grid. In that case, removing the screws and grid as described in b)–e) is not
necessary
Figure 6
Figure 7
Figure 8
Figure 9
When mounting, make sure that the plastic sleeve is properly attached to the ventilation grid (refer to fig. 8 to see proper mounting).
Important Note:
Reproduction and any commercial use (of parts) of this operating manual,
requires a written permission of Wilted Wild anger Technique GmbH.
Contact Us
The information contained in this document may alter at any time without prior notice. No part of this document may be copied or otherwise duplicated without prior written consent. All rights reserved.
Wilted Wild anger Technical GmbH cannot be held liable for any possible mistakes in this operating manual, nor in the diagrams and illustrations shown.
Although Wilted Wild anger Technical GmbH has made every possible effort to
ensure that this operating manual is complete, accurate, and up-to-date,
errors cannot be ruled out entirely. If you have found an error or wish to
suggest an improvement, we look forward to hearing from you.
Send us an e-mail to: service@wiltec.info
or use our contact form:https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in our online shop: https://www.wiltec.de/docsearch
Our postal address is:
Wilted Wild anger Technique GmbH
Königs benden 12
52249 Eschweiler Germany
To return your goods for exchange, repair, or other purposes, please use the following address. Attention! To allow for a trouble-free complaint or return, it is important to contact our customer service team before returning your goods.
E-mail:service@wiltec.info
Tel: +49 2403 55592–0
Fax: +49 2403 55592–15
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>