Trelleborg Wheel Systems Italia TLCP01 TPMS Sensor User Manual
- June 5, 2024
- Trelleborg Wheel Systems Italia
Table of Contents
Trelleborg Wheel Systems Italia TLCP01 TPMS Sensor
Safety Information
- Please make sure that you have read and understood the information contained in user’s manual. Keep the manual for future use.
- Keep the product out of reach of children. The product contains parts that may be ingested or cause suffocation.
- Keep the product away from hazardous chemical substances and heat sources.
- Do not expose the receiver and battery charger to water and other liquids. Do not touch the product with wet hands.
- Use only the battery and charger provided in the kit. Improper use of battery or replacement with an incorrect battery type may cause fire, explosion or other risks. Dispose of batteries in compliance with existing regulations.
- Do not disassemble the product. Battery replacement must be performed by authorized personnel only. Do not use damaged battery chargers.
- Keep the battery away from high-power electronic devices and heat sources. Do not expose batteries at temperatures outside the temperature range specified in the manual. It is recommended to charge batteries at room temperature between +5°C and +25°C.
- Before using the product, make sure that it is suitable to the vehicle type. Check periodically the status of tire valves against environmental agents such as corrosion.
- Replace tire valves that appear to be damaged. Also check periodically the status of tires, as the product cannot be used to monitor tire tread wear.
- Sensors weight is too low to affect wheel balancing, anyway in case excessive vibrations should occur at high speed, check wheel balancing again.
- Always make sure that sensors are firmly tightened to the valves to avoid air leakage.
- In case strong interfering radio signals are present in nearby area, the system may function intermittently or stop functioning.
- For any problem please contact specialized personnel.
Radiofrequency Information
TPMS Transmitter
Frequency Band| Max. Output Power
434 MHz – Micro.sp Technology| -24.92 dBM ERP
TPMS Gateway
Frequency Band| Max. Output Power
2.4 GHz – BLE| 0 dBm – 1mW ERP
Disposal Information
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service, or the shop where you purchased the product.
EC Compliance
This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market. This product conforms to the essential requirements of the RED directive 2014/53/EU in order to attain CE Marking. The manufacturer has demonstrated compliance of radio equipment with the essential requirements using the internal production control set out in Annex II of directive 2014/53/EU.
FCC Compliance
FCC Interference Statement – Part 15.105 (b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Part 15 Clause 15.21
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Part 15.19 (a)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Manufacturer
- Trelleborg Wheel Systems Italia SpA
- via Nazionale Tiburtina 143, Villa Adriana (Tivoli) – Rome – Italy
- tws.it@trelleborg.com
- TEL: +39.0774.384.1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>