Jem WM-AC201 Wireless module User Manual

JEM Product user’s manual
802.11AC 2T2R Module
Model : WM-AC201
Datasheet Number: UM-WM-AC201
Reversion 1.0
Author:
JEM, TAIWAN

PROPRIETARY NOTE

This item is the property of JEM Inc., Taipei, Taiwan and trade secret information. This item may not be transferred from the custody of JEM Inc., except as authorized by EM Inc. and then only by way of loan for limited purposes. It must not be reproduced in whole or in part and must be returned to JEM Inc. upon request and in all events upon completion of the purpose of the loan. Neither this item nor the information it contains may be used by or disclosed to persons not having a need for such use or disclosure consistent with the purpose to the loan without prior written consent of JEM Inc.
Revision and history:

About
This specification is a preliminary product specification written by Joinsoon Electronics MFG. Co., Ltd for the “WM-AC201 AC 2T2R Module”.

Product description

WM-AC201 is a highly integrated 802.11a/b/g/n/ac 2T2R module that supports 2-stream 802.11ac solutions with Multi-user MIMO. It integrates a high- performance 1GHz  IPS24Kc  processor, Fast Ethernet switch with RGMII, USB2.0 controller, DRAM and flash memory controller, and useful peripheral interfaces. It combines a WLAN MAC, a T2R capable WLAN baseband. It provides a complete solution for a high throughput performance integrated wireless LAN device. It is designed to provide excellent performance with low power consumption and enhance the advantages of a robust system and cost- effectiveness. It is targeted at competitive superior performance, better power management applications The RTL8197F delivers high-performance with low power consumption for applications such as 11ac dual-band smart routers, IoT gateway, VPN gateway, VoIP gateway, Network Storage, LTE routers, etc.

Product features

• IEEE802.11a/b/g/n and 802.11ac compliant.
• Operates at 2.4GHz and 5GHz frequency bands.
• CPU MIPS 24Kc speed up to 1GHZ
• Chipset embedded DDRII 128MB
• Support STBC, transmit Bean Forming.
• Modulation: BPSK, QPSK,16 QAM, 64-QAM, 256-QAM, OFDM.
• WPA, WPA2 and hardware accelerated AES encryption/decryption.
• Support 2T/2R transmission rate 300Mbps in 802.11n, and 867Mbps in 802.11ac(Physical rate) at 20MHz /40Mhz /80MHz Bandwidth.
• Support Multiple SSID
• QOS: Traffic Control & WMM/WMM-PS
• Various peripheral: USB host, UART, WAN Port, GPIO.. and so on.
• USB2.0 support for date rates up to 480Mbps high speed
• 2 IPEX Antenna Connectors (with 2 switches for 2.4G/5G selection)
• Support AP client for internet access.
• Support PC/NB wireless access interface
• Support UPnP medial (DLNA compatible ) access
• Dimension 62x33x5 mm

Application

• Mobile Internet Device
• TV
• IP-cam
• STB

Mechanism

Pin Definition

I: Input
O: Output
P: Digital Power
G: Digital Ground| AI: Analog Input
AO: Analog Output
AI/O: Analog Bi-Directional Input/Output
I/O: Bi-Directional Input/Output
---|---

*J13 18pin(92)
**

*J14 14pin(72)**

J18 7pin(7*1)

Pin out Specification

VDD: Digital I/O Power in 3V3
GND: Digital ground
GOIO: General-purpose In /Out interface. Internal pull-High/pull-down Resistor
※GPIOH4 internal pull-down only in strap period, GPIOC7 None

General Specification

**Antenna support list

**

This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated.

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide easonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For products available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device is restricted to indoor use.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment this equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.

This module is intended for OEM integrators under the following conditions: This module is certified pursuant to two Part 15 rules sections(15.407, 15.247).
Label of the end product:
The host product must be labeled in a visible area with the following ” Contains
FCC ID: N8J-WFMD001 “.
The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This module is restricted to integration into hosts for indoor use only.
This module has been approved under a stand-alone configuration.
OEM integrator has be limited the operation channels in channels 1-11 for the 2.4GHz band.
The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations The information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, , versus with multiple, simultaneously transmitting modules or other transmitters in a host can be found at KDB Publication 996369 D04
Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. SDoC) of the host product to be addressed by the integrator/manufacturer. This module is only FCC authorized for the specific rule parts 15.247, 15.407 listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host product as being Part 15 Subpart B compliant.

The user manual of the end product
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>