POS Terminal MICROS Workstation 8 User Guide
- June 3, 2024
- POS
Table of Contents
POS Terminal
(Model: MICROS Workstation 8)
Basic Operation Guide
Overview of MICROS Workstation 8
Here introduce ORACLE new generation of POS Terminal, model MICROS Workstation
8.
Getting to know your Workstation
MICROS Workstation 8 Front View
- Power button with LED indicator
- 14” touch LCD
- Camera
MICROS Workstation 8 Rear View
- Hook (4 in total), to install the MICROS Workstation 8 on the Stand
- Input, output interfaces
MICROS Workstation 8 I/O View
| 1 | USB C Out (5V/9V/15V) | Power to CFD (5V, 2A) |
|---|---|---|
| 2 | Micro USB LAN Port | Gigabit LAN |
| 3 | USB C Power In | Power from adaptor |
| 4 | CMOS reset button | Not end user use |
MICROS Workstation 8 – Hardware Specification
| Specification | Parameter |
|---|---|
| Processor | Alt. supporting CPU sources: IntelOAtom® 6000 Series processor |
Intel® J6426 (2GHz, 4 core), Intel® J6413 (1.6GHz, 4 core) , Intel® X6413E
(1.5GHz,4 core) Intel® X6211E (1.3G, 2 core)
Memory| Installed memory (RAM) up to 8GB SSD up to 256GB
Display with touchscreen| LCD display
•Type: TFT, supports transmissive display mode
•Size: 14″ TFT LCD Display
Network| Gigabit LAN
WIFI&BT| 802.11a/b/g/n WIFI and Bluetooth module
RFID| 13.56MHz and 125kHz
Modulation ASK
Button/Switch| One Power Button
Rating| DC 15V, 2A
Weight| About 0.8kg
Dimension| 320 x 190 x 10 mm
Storage Temperature| -20 to 70 degrees Celsius
Operating Temperature| 0 to 50 degrees Celsius Passively cooled
Operating Humidity| Up to 90% relative humidity non condensing @ 50 Celsius
Using Your MICROS Workstation 8
Positioning Your MICROS Workstation 8
- Place the Vertical Stand or Low Profile Stand on a flat surface like a table or desk.
- Align and insert the Workstation on the docking plate, and make sure all four hooks securely attach to the mounting holes of the Stand.
- Confirm the Workstation firmly lock on the Stand.
- To remove Workstation 8 from the Stand, press the unlock button to release the Workstation
- There are two Stands shown below for installing the Workstation, mounting methods are same.
Working with Windows® 10
Starting for the first time
When you start your MICROS Workstation 8 for the first time, a series of
screens may appear to guide you in configuring the basic setting of your
Windows ® 10 operating system.
Follow the instructions to configure.
Once you are done configuring the basic items, a Windows ® 10 Start screen
appears after successfully signing in to your user account. It helps organize
all the programs and applications you need in just one place.
Turning off the Station
Do either of the following to shut down your Station.
- Tap from the Charm bar then tap > shut down to do a normal shutdown.
- From the log-in screen, tap > shut down.
- If your Workstation is unresponsive, press and hold the power button for at least 4 seconds until your Express Station turns off.
Appendix – Regulatory Caution
FCC Class A Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy, and if it
is not installed and used in accordance with the instruction manual, it may
cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in
which case the user will be required to correct the interference at his own
expense. Modifications: Any modifications made to this device that are not
approved by Oracle may void the authority granted to the user by the FCC to
operate this equipment. To satisfy FCC/IC RF exposure requirements, a separate
distance of 20 cm or more should be maintained between the antenna of this
device and persons during device operation.
To ensure compliance, operation closer than this distance is not recommended.
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
(i)the device for operation in the band 5150-5250 MHz is only for indoor use
to reduce the potential for harmful interference to co-channel mobile
satellite systems;
(ii)the maximum antenna gain permitted for devices in the bands 5250-5350 MHz
and 5470-5725 MHz shall comply with the e.i.r.p. limit;
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>