CryptoDATA Whim Pro N141 Laptop User Manual
- June 5, 2024
- CryptoDATA
Table of Contents
CryptoDATA Whim Pro N141 Laptop
INTRODUCTION
- This manual is mainly for Windows 10. There might be some slight differences if you use other windows systems.
- This manual contains the common functions of most models. Maybe it does not fit very well with your model for some functions, or maybe some of your model functions are not contained in this manual.
- The illustrations in this manual may differ from the actual products. Please prevail in kind.
Front View
Attention
Using the keyboard
Keyboard function keys
Pressing certain function key to enter the corresponding system settings
immediately
Keyboard Function
Through the use of the function keys, you can change operational feature instantly. To use this function, press and hold ; then press one of the function keys
Positioning the display panel.The display panel can be opened to any angle up to 180 degrees.
Note:
- Do not open the display with too much force, otherwise the panel or hinges may be damaged.
- Do not rotate the camera with too much force, otherwise the camera may be damaged.
Left View
USB 2.0Port
You can connect a USB device to your computer by inserting its USB plug (Type
A) into the USB port on your computer.
Combo Audio Jack
- The combo audio jack does not support a conventional microphone connection.
- Due to differences in industry-standard, when third-party connects headphones or headset microphone, recording functions may not be supported well.
Right View
UDisk Port
You can connect a Type C device to your computer by inserting its USB plug
(Type C) into the Type C port on your computer.
Switch
Control camera, mic on and off.
Micro SD Card Slot
- The computer supports the following types of memory cards:
- Micro Secure Digital (SD) card
- Micro Secure Digital High Capacity (SDHC) card
- Micro Secure Digital Extended Capacity (SDXC) card
Type C Port
You can connect a Type C device to your computer by inserting its USB plug
(Type C) into the Type C port on your computer.
HDMI Port
You can plug the HDMI display device into the computer connected to the HDMI
port
USB 3.0Port
You can connect a USB device to your computer by inserting its USB plug (Type
A) into the USB port on your computer.
Note：
- You can only insert one memory card in the slot each time.
- Please insert memory card until into the bottom of the slot.
- Remove the memory card from the memory card slot and gently pull the memory card out of the slot.
- Before removing the memory card, safely remove hardware and eject media utility to disable the card to avoid data corruption.
Bottom View
Configuring the operating system in initial use.
The first time you use, you need to configure the operating system. The configuration process may include the following steps:
- Accepting the End User License Agreement
- Configuring the Internet connection
- Registering the operating system
- Creating a user account
Operating System Interface
- Windows 10 comes with a powerful and useful start menu.
- To open the start menu, do one of the following:
- Press the Windows key on the keyboard
- Select Start on the lower-left corner of the desktop
Settings Button
Settings let you perform basic tasks. You can also search for more settings with the settings search box in the upper-right corner. To open the settings, do the following: Open the Start menu and select Settings
Power Button
The power button is on the Start menu, click it you can choose to shut down or
restart the computer, or put the computer into sleep mode.
Start Button
Select the Start button on the taskbar, open the start menu
Search Box
Search for anything, anywhere
Start menu
You can personalize the start menu with your favorite apps. To personalize the Start menu, do the following: Right-click the application which you want to add to the Start menu, then select Pin to Start menu.
Keep the computer in sleep mode or shut down
When you finish using your computer, you can turn the computer into sleep mode
or shut down.
Putting your computer to sleep
- If you will be away from your computer for only a short time, put the computer to sleep.
- When the computer is in sleep mode, you can quickly wake it to resume use, by passing the startup process.
- To turn the computer to sleep mode, do one of the following:
- Close the display lid.
- Press the Power button.
- Open the Start menu, and then select power sleep
- To wake the computer, do one of the following:
- Press any key on the keyboard. (Notebook only)
- Press the power button.
Turn off the computer
- If you will not use your computer, please turn off the computer.
- To shut down the computer, do one of the following:
- Open the Start menu, and then select power – shut down
- Right-click the Start button on left bottom, and then select shut down or log off.
Tasks view
- To open the task view, do one of the following:
- Select the task view button on the taskbar.
- Press the Windows + Tab key.
- Swipe from the left edge of the screen to the middle.
Connect to the wireless network
- Enabling wireless connection
- To enable the wireless feature, do the following:
- Click the network menu on the right bottom of the taskbar , to open the Network configuration page
Connect to a wireless network
- The computer will automatically scan for available wireless networks and list them in the list when wireless is enabled.
- Click the network name in the list to choose, and click Connect
Troubleshooting
Common problems
- Display issues
- When I turn on the computer, nothing appears on the screen.
- If the screen is blank, please make sure:
- The AC power adapter is connected to the computer, and plugged into a working electrical outlet.
- The computer power is on. Press the power button again to confirm.
- If these items are properly set, and the screen remains blank, have the computer serviced.
- The screen goes blank while the computer is on
- Your screen saver or power management may be enabled. Do one of the following to resume from sleep mode:
- Press any key on the keyboard. (Notebook only)
- Press the power button.
- Sleep problems
- The critical low-battery error message appears, and the computer immediately turns off.
- The battery power is getting low. Connect the AC power adapter to the computer.
- The computer does not return from sleep mode, and the computer does not work.
- If the computer is in sleep mode, please connect the AC adapter to the computer, and then press the Power button..
- If the system still does not return from sleep mode, stops responding, or cannot be turned off, reset the computer. Unsaved data may be lost. To reset the computer, press and hold the Power button for eight seconds or more. If the computer is still not reset, remove the AC power adapter.
- Voice problems
- Even turn up the volume, you still cannot hear any sound from the speaker. Make sure that:
- Mute function is turned off.
- Do not use combo audio jack.
- The speakers are selected as a playback device.
- Battery problems
- Your computer shuts down before the battery indicator shows empty
- Recharge the battery
- Other problems
- The touchpad does not function well
- Press key “Fn+F7” to make sure the touchpad is turned on. The computer is not responding
- To turn off your computer, press and hold the Power button for eight seconds or more. If the computer still does not respond, remove the AC power adapter.
- Your computer might lock when it enters sleep mode during a communication operation. Disable the sleep timer when you are working on the network. The connected external device does not work
- Do not connect or disconnect the non-USB cable device in the boot state, otherwise you may damage your computer.
- When using high power consumption external devices such as an external USB optical disk drive, use an external device power adapter. Otherwise, the device may not be recognized, or the system may shut down as a result.
FCC statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IC statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>