MARKONE A000010007A BT/Wi-Fi Combo Module Gen6 User Manual
- June 5, 2024
- MARKONE
Table of Contents
MARKONE A000010007A BT/Wi-Fi Combo Module Gen6 User Manual
Product Specification
| PRODUCT | BT(v4.2) & WLAN(802.11a/b/ g/n/ac) 2.4G SISO/5G MIMO |
|---|---|
| SPECIFICATION MODEL NAME : | 6+ BT/wifi Combo Module |
| MODEL CODE | A000010007A |
Application
This specification is applied to MarkoneTechnology Bluetooth (v4.2)and 2.4GHz SISO/5GHz MIMO WLAN(802.11a/b/g/n/ac) Module A000010007A which includes BCM88359/CYW88359
Quality
Quality must meet each condition mentioned in this specification.
Appearance and Characteristics
-
Appearance
The appearance should not be contaminated with harmful substances, and there should be no cracks, etc. Mechanical dimensions must meet the provisions of paragraph 7. -
Characteristics
Electrical characteristics should meet the contents of clause 9
Application of Bluetooth v4.2 and 2.4GHz/5GHz WLAN(IEEE
802.11.a/b/g/n/ac)
Automotive
Maximum Rating
| NO | ITEM | Rating | UNIT |
|---|---|---|---|
| 1 | Operating Temperature Range | -40 ~ +85 | ℃ |
| 2 | Storage Temperature Range | -40 ~ +105 | ℃ |
| 3 | VBAT Voltage Range | -0.5 ~ 6.0 | V |
| 4 | VIO Voltage Range | -0.5 ~ 3.9 | V |
| 5 | VBAT Max. Current | 700(@3.3V) | mA |
| 6 | VIO Max. Current | 50(@1.8V) | mA |
General Features
BT(v4.2) + 2.4GHz/5GHz WLAN(IEEE 802.11a/b/g/n/ac) 2.4G SISO/5G MIMO
Features
- Operation Voltage is 3.3V/1.8V Dual Power Rail
- WiFi Single-stream up to 866 Mbps data rate
- Automotive Module : All components are AEC-Q 100/200 qualified
- Support 2 Antenna port : ANT0 : Bluetooth/5G WLAN, ANT1 : 2.4G/5G WLAN
- Integrated WLAN PA, RF Switch and LNA
- RoHS Compliant
- Size : 35.3 x 35.3 x 7.8 mm3
- Support bandwidth : HT20 / HT40 / VHT80
- HOST Interface : PCIE/SDIO(WLAN), UART(BT), PCM(I2S)
- Package type : Connector type(B to B)
Bluetooth(BT v4.2+EDR compliant)
Bluetooth Key Features
Supports key features of upcoming Bluetooth standards
- Fully supports Bluetooth Core Specification version 4.2 + (Enhanced Data Rate) EDR features:
- Adaptive Frequency Hopping (AFH)
- Quality of Service (QoS)
- Extended Synchronous Connections (eSCO) – Voice Connections
- Fast Connect (interlaced page and inquiry scans)
- Secure simple Pairing (SSP)
- Sniff Sub rating (SSR)
- Encryption Pause Resume (EPR)
- Extended Inquiry Response (EIR)
- Link Supervision Timeout (LST)
- UART baud rates up to 4 Mbps
- Supports all Bluetooth 4.2 packet types
- Supports maximum Bluetooth data rates over HCI UART
- Multipoint operation with up to seven active slaves
- Maximum of seven simultaneous active ACL links
- Maximum of three simultaneous active SCO and eSCO connections with scatternet support
- Narrowband and wideband packet loss concealment
- Scatternet operation with up to four active piconets with background scan and support for scatter mode
- High-speed HCI UART transport support
- Channel quality driven data rate and packet type selection
- Standard Bluetooth test modes
- Extended radio and production test mode features
- Full support for power savings modes
- Bluetooth clock request
- Bluetooth standard sniff
- Deep-sleep modes and software regulator shutdown
WLAN
- WLAN RF band & modulation Features
- Dual-band 2.4GHz and 5GHz 802.11 a/b/g/n/ac(802.11ac compliant)
- Up to 866Mbps data rate
- Supports 20, 40 and 80MHz channels with optional SGI(256 QAM modulation)
- Tx and Rx low-density parity check(LDPC)
- Supports IEEE 802.11ac/n beamforming
- Supports PCIe v3.0-compliant interface running at GEN1 speeds
- Supports two antennas with Bluetooth/5G WLAN and 2.4G/5G WLAN antenna
- Supports standard SDIO V3.0 (up to SDR104 mode at 208MHz, 4 bit and 1-bit)
- Backward compatibility with SDIO v2.0 host interface
- WPA and WPA2(Personal) support for powerful encryption and authentication
- AES and TKIP in hardware for faster data encryption and IEEE 802.11i compatibility
- Reference WLAN subsystem provides Wi-Fi protected Setup(WPS)
- WLAN MAC features
- Enhanced MAC for supporting IEEE 802.11ac features
- Transmission and reception of aggregated MPDUs(A-MPDU) for high throughput(HT)
- Support for power management schemes, including WMM power save multi-poll(PSMP) and multiphase PSMP operation
- Support for immediate ACK and block-ACK policies
- Inter-frame space timing support, including RIFS
- Back-off counters in hardware for supporting multiple priorities as specified in the WMM specification
- Timing synchronization function(TSF), network allocation vector(NAV) maintenance, and target beacon transmission time(TBTT) generation in hardware
- Hardware offload for AES-CCMP, legacy WPA TKIP, legacy WEP ciphers, WAPI, and support for key management
- Programmable independent basic service set(IBSS) or infrastructure basic service set functionality
- WLAN PHY features
- Programmable data rates from MCS0-9 in 20MHz, 40MHz, and 80MHz channels, as specified in IEEE 802.11ac
- Improved performance with channel smoothing and spur canceller support
- Supports Optional short GI and Green field modes in Tx and Rx
- Tx and Rx LDPC for improved range and power efficiency
- Beam forming support
- Supports IEEE 802.11h/k for worldwide operation
- Advanced algorithms for low power, enhanced sensitivity, range, and reliability
- IEEE 802.11a, 11b, 11g, 11n, 11ac single stream PHY standards
- Designed to meet FCC and other worldwide regulatory requirements
JEDEC MSL JEDEC MSL (Moisture Sensitivity Level) Test
- MSL 3 Level (Floor Life Time : 168Hrs. / Condition : ≤30℃, 60% RH)
- Standard : IPC / JEDEC J-STD-020C
Electrical Specification
Operating Conditions
Recommended operation conditions
| Parameters | Min | Max | Unit |
|---|---|---|---|
| Operating Temperature Range | -40 | +85 | ℃ |
| Supply Voltage : VBATT (3.3V) | 3.01) | 3.6 | V |
| Supply Voltage : VIO (1.8V) | 1.62 | 1.98 | V |
Current consumption
| Parameters | Average | Unit |
|---|---|---|
| Stand-by (BT & WLAN) | 10 | mA |
| WLAN Continuous Rx | 180 | mA |
| WLAN Continuous Tx2) | 420 | mA |
| Bluetooth Connection | 20 | mA |
ESD Precautions
A1000010007A is classified as a JESD22-A114(HBM) class 1C(1kV) product. Apply
ESD static handling precautions during manufacturing
External 32.768KHz low-power oscillator(LPO)
External 32.768KHz precision oscillator is required.
| Parameters | LPO clock | Unit |
|---|---|---|
| Nominal input frequency | 32.768 | KHz |
| Frequency accuracy | ±200 | ppm |
| Single input amplitude | 200 ~ 3300 | mV, p-p |
| Signal type | Square-wave or sine-wave |
FCC Warning Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF Radiation exposure limits set forth for an
uncontrolled environment.
This device and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 20
cm between the radiator and your body
ISED Warning Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device
IC RF Radiation Exposure Statement
This equipment complies with IC RF Radiation exposure limits set forth for an
uncontrolled environment.
This device and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 20
cm between the radiator and your body
Please notice that if the FCC/IC identification number is not visible when the
module is installed inside another device, then the outside of the device into
which the module is installed must also display a label referring to the
enclosed module. This exterior label can use wording such as the following:
“Contains FCC ID: 2AVZC-A000010007A”
“Contains IC: 26076-A000010007A”
any similar wording that expresses the same meaning may be used
Manual Information to the End User
The module is limited to OEM installation ONLY.
The OEM integrator is responsible for ensuring that the end-user has no manual
instruction to remove or install module.
The module is limited to installation in mobile application;
A separate approval is required for all other operating configurations,
including portable configurations with respect to Part 2.1093 and difference
antenna configurations.
There is requirement that the grantee provide guidance to the host
manufacturer for compliance with Part 15B requirements.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>