Boltpower HFT160 Jump Starter and Power Bank User Manual

Boltpower HFT160 Jump Starter and Power Bank

Apart from jump starting a car, this product can also supply power for a mobile phone, tablet, PSP, MP3/MP4, camera and other consumer electronics, and with different lighting modes.

How to Jump Start a 12V vehicle?

1. Check the Jump Starter and make sure the power is over 50% charged.

2. lnsert the jumper cable to the product’s jump start socket. The Jumper cable’s GREEN LED “ ” would be flashing. This means that the product is in “Stand-by mode”.
   

3. Connecting the RED clamp to the POSITIVE terminal(+), and BLACK clamp to the
   NEGTIVE terminal(-) of the vehicle battery. The Jumper cable’s LED light would be turned into Solid GREEN “ “. It means that the product is in “Jump Start Ready mode”.
   | Once the product is in “Jump Start Ready mode”, you will have seconds to Jump Start the engine.
   ---|---

4. Press the car start button or turn the ignition switch to the START position.
   

5. Disconnect the jumper cable from the product, then remove the clamps from the vehicle battery.
   

Jumper cable description

Description| LED display| Buzzer Warning
Stand-by mode| (Flashing)| I
Jump Start Ready mode| (Solid GREEN)| I
Jump start over time mode| (Solid RED & GREEN)| I
Short-circuit protection| (Solid RED)| Beeps rapidly
Reverse Polarity protection| (Solid RED)| Beeps rapidly
Reverse Charging protection| (RED & GREEN Flashes alternate!y)| I
Low Voltage protection| (Solid RED)| Beeps 1 time per second
High Temperature protection| (Solid RED & GREEN)| Beeps 1 time per second
Malfunction alarm (Warning: Stop using the jumper cable.| (Solid RED)| Keeps long beeping

LCD screen display instructions

1. When charging, the LCD displays “IN”, and the battery percentage value flashes (1 flash per second). When the battery is charged to 100%, it stops flashing and stops charging; after 10 seconds, the LCD display is turned off and enters the sleep state.
2. When discharging output, the LCD displays “OUT” and the current percentage of power of the product is displayed at the same time.
3. The USB port discharges output corresponds to displaying “5V/ 2.4A” or “QC 3.0” characters.
4. When the TYPE-C port discharges output, the character “5V/3.0A” is displayed.
5. When wireless charging is working: the ” ” symbol shows the current working status (” ” flashes quickly when the wireless charging is abnormal).
6. In the working state, the discharge of jump start port can normally indicate the electric quantity.
7. When no load or light load is connected, 30±5S after the LED screen goes out and enters the sleep mode.
8. When the battery temperature is abnormal, the ” ” symbol flashes.

How to use wireless charging ?

Press the “Power ” button to turn on the wireless feature, the would be solid on.

You can go ahead and place your phone over the wireless charger pad.

How to charge mobile phone or tablet

1. Turn on the product
2. Connect the product to your device via charging cable.

How to turn on the LED light?

Hold for 2 seccnds to turn on the LED light.
Short press one time, switch to SOS or flash light mode.
Hold for 2 seccnds to turn OFF the LED light.

How to recharge the product?

First step:

Insert the charging cable.

**Second step:

**

Connect the charging cable to a DC 5V/3A USB port to recharge the product.

Specification:

Product structure diagram

① Power button
② Jump start port
③ Type-C input/output
④ Wireless charging
⑤ LCD screen
⑥ LED light / SOS / strobe
⑦ USB output
⑧ Wireless charging

What’s in the box ?

Warning

1. This product was desinged for 12V lead acid/AGM/Gel batteries/ vehicles ONLY.
2. Never short circuit the jump starter by connecting the RED and Black clamps.
3. Do not disassemble the jump starter.
4. Do not use ii as a toy for Chirdren.
5. Store in a dry place, do not expose to damp conditions or near corrosive materials.
6. If the jump starter expands, leakage or peculiar smell is found, stop use immediately.
7. Please use this jump starter at normal temperature and be far away from too wet, too hot and fire.
8. “DO NOT jump start the car engine more than 3 times continuously as ii may overheat or damage the product”, there should be an interval of 60 seconds between each jump start.
9. When the battery power of the unit is less than 10%, do not use the jump starter as it will damage the unit.
10. Recharge the unit every 3 months to prevent from being over-discharged.
11. Before first use, charging for 3 hours or more.
12. After starting the car, please wait at least 30 minutes before charging the product.
13. Be sure to use the standard jumper cable that comes with the product to start the vehicle.

Warranty Card

We offer 12 months warranty service from the dates of purchase .
Warranty Condition: When you need warranty service, please show this warranty card, and write down detailed related content. Our comany offer 12 months warranty service from the dates of purchase.
Warranty Range: Quality problems under normal use

Note:

1. As a result of operational errors caused by damage to the product, no warranty.
2. After the unauthorized disassemble, no warranty.
3. Torn product label, no warranty.

If product is not in above warranty range, our company can provide maintenance services, and costs need to be paid by customer.

Model| | Serial number|
---|---|---|---
Purchase dates| | Serial numberb|
Customer Name| | Telephone|
Address|
Seller|
Description of product anomalies

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in 3 residential installation.This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a determined particular installation. If this equipment does cause harmful interference to radio or television reception, which can be by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for  help.

FCC Radiation Exposure Statement

The device has been evaluated to meet general RF exposure requirement.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>