HILTI SSH6­22 Double Cut Metal Slitting Shear Instructions

HILTI SSH6­22 Double Cut Metal Slitting Shear

Original operating instructions

Information about the documentation About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product.
• Observe the safety instructions and warnings in this documentation and on the product.
• Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons.
Explanation of symbols
Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words are used:
DANGER
Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING
Draws attention to a potential threat of danger that can lead to serious injury or fatality.
CAUTION
Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the equipment or other property.

Symbols in the operating instructions
The following symbols are used in these operating instructions:

Symbols in illustrations
The following symbols are used in illustrations:

Product-dependent symbols

Symbols on the product
The following symbols can be used on the product:

Product information

products are designed for professional users and only trained, authorized personnel are permitted to operate, service, and maintain the products. This personnel must be specifically informed about the
possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used not in accordance with the intended use. The type designation and serial number are printed on the rating plate. Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product.
Product information

Safety

General power tool safety warnings

WARNING
Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. Work area safety

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. The use of an RCD reduces the risk of electric shock.

Personal safety

• Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean, and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. The use of any other battery packs may create a risk of injury and fire.
• When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts the eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130° C (265 °F) may cause an explosion.
• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

Additional safety instructions

Personal safety

• Use the product and accessories only when they are in perfect working order.

• Never tamper with or modify the product or accessories in any way.

• Dust produced by grinding, sanding, cutting and drilling can contain dangerous chemicals. Some examples are: lead or lead-based paints; brick, concrete, and other masonry products, natural stone and other products containing silicates; certain types of wood, such as oak, beech, and chemically treated wood; asbestos or materials that contain asbestos. Determine the exposure of the operator and bystanders by means of the hazard classification of the materials to be worked. Implement the necessary measures to restrict exposure to a safe level, for example by the use of a dust collection system or by the wearing of suitable respiratory protection. The general measures for reducing exposure include:

• working in an area that is well ventilated,

• avoidance of prolonged contact with dust,

• directing dust away from the face and body,

• wearing protective clothing and washing exposed areas of the skin with water and soap.

• Touch the power tool by the insulated gripping surfaces only, when carrying out work in which the accessory tool can come into contact with concealed wiring.

• Wear protective gloves. The cut edges and metal swarf are sharp-edged and there is a risk of cut injuries. The product and the workpiece become hot in the working process and there is a risk of burn injuries.

• Wear protective gloves also when changing the accessory tool. Touching the accessory tool presents a risk of injury (cuts or burns).

• Take frequent breaks and do physical exercises to improve the blood circulation in your fingers. High vibration during long periods of work can lead to disorders of the blood vessels and nervous system in the fingers, hands, and wrists.

• Wear eye protection, a hard hat, and ear protection while the product is in use.

• Switch the product on only after you have brought it to the working position.

• Wait until the product has come to a complete stop before you lay it down.

• Do not work overhead with the product.

• Risk of injury by falling tools and/or accessories. Before starting work, check that the battery and installed accessories are secure.

• Do not secure a belt hook to this powerful tool.

• Keep the air vents clean at all times. Risk of burn injuries due to blocked air vents!
  Electrical safety

• Have dirtied or dusty products that are used frequently for working on conductive materials checked at regular intervals by Hilti Service. Dust, especially dust from conductive materials, or dampness on the surface of the product can, under unfavorable conditions, lead to electric shock.

• Clean the ventilation slots on the power tool at regular intervals. The motor’s fan will draw the dust inside the housing and an excessive accumulation of metal dust may cause electrical hazards.

• Before beginning work, check the working area (e.g. using a metal detector) to ensure that no concealed electric cables or gas and water pipes are present. External metal parts of the product can become life, for example, if you inadvertently damage electric wiring.

• Do not attempt to cut workpieces that could be electrically live.

Work area safety

• Keep the work area clean and tidy. The metal swarf is sharp and can scratch the floor surface.
  Careful handling and use of electric tools

• Make sure that there is no swarf or dirt on the product. When working, make sure that no swarf makes its way into the area of the on/off switch. The swarf could block the on/off switch, rendering it impossible to switch the product off.

Battery use and care

• Comply with the following safety instructions for the safe handling and use of Li-ion batteries. Failure to comply can lead to skin irritation, severe corrosive injury, chemical burns, fire, and/or explosion.
• Use only batteries that are in perfect working order.
• Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely harmful to health!
• Do not under any circumstances modify or tamper with batteries!
• Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C (176 °F).
• Never use or charge a battery that has suffered an impact or been damaged in any other way. Check your batteries regularly for signs of damage.
• Never use recycled or repaired batteries.
• Never use the battery or a battery-operated power tool as a striking tool.
• Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This can lead to explosions.
• Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects. This can damage the battery and also cause material damage and personal injury.
• Keep batteries away from rain, moisture, and liquids. Penetrating moisture can cause short circuits, electric shock, burns, fire, and explosions.
• Use only chargers and power tools approved for the specific battery type. Read and follow the relevant operating instructions.
• Do not use or store the battery in explosive environments.
• If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to cool down. If it is still too hot to touch after an hour, the battery is faulty. Consult Hilti Service or read the document entitled “Instructions on safety and use for Hilti Li-ion batteries”.

Observe the special guidelines applicable to the transport, storage, and use of lithium-ion batteries. Read the instructions on the safety and use of Hilti Li-ion batteries that you can access by scanning the QR code at the end of these operating instructions.

Description

Product overview

1. Swarf cutter
2. Lockable on/off switch
3. Grip
4. Adjusting the knob for speed
5. Battery status indicator
6. Battery release button
7. Battery
8. Dust filter
9. Bearing pin
10. Blade
11. Cut-off plate
12. Mark for swarf cut-off

Intended use
The product described is a hand-held, cordless slitting shear. It is designed for cutting sheet-like workpieces out of steel, aluminum, plastic, or comparable materials. It can be used to cut along a marked line, for cutting straight or curved outside edges, and for cut-outs. The strip of the swarf can be cut off at any point on the workpiece.

• For this product, use only Hilti Nuron lithium-ion batteries of the B 22 series. For optimum performance, Hilti recommends the batteries stated in the table at the end of these operating instructions for this product.
• For these batteries, use only Hilti chargers of the type series stated in the table at the end of these operating instructions.

Items supplied
Slitting shear, Torx wrench, operating instructions

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables, and accessories approved by Hilti for use with the product can be found at your local Hilti Store or online at: www.Hilti.group
Before being dispatched, the product was tested to ensure that it is in full working order. Their workpiece used in testing might have left tiny scratches on the surface of the housing.

Temperature-dependent motor protection
The temperature-dependent motor protection system monitors current input and motor temperature and thus prevents the power tool from overheating.
If the motor is overloaded through the application of excessive working pressure, the product’s performance drops noticeably or it might stall completely.
If the product stalls or slows significantly due to overloading, relieve the pressure applied to the product and then allow it to run under no load for approx. 30 seconds.

Status indicators of the Li­ion battery

Hilti Nuron Li-ion batteries can indicate the state of charge, fault messages, and the battery’s state of health.

Indicators for the state of charge and fault messages

WARNING

Risk of injury by a falling battery

• If the release button is pressed with a battery inserted in the product, subsequently check that the battery is correctly re-engaged and secure.

Short-press the release button of the battery to get whichever of the following status indications is applicable at the time. State of charge and, if applicable, faults are indicated constantly as long as the connected product is switched on.

Recharge the battery.

If the LED again starts quick-flashing after the bat-

there has been charged, consult Hilti Service.

One (1) LED quick-flashes yellow| The Li-ion battery or the product in which it is in started is overloaded, too hot or too cold, or experiencing some other fault.

Bring the product and the battery to the recommended working temperature and do not overload the product when it is in use.

If the message persists, consult Hilti Service.

One (1) LED shows yellow| The Li-ion battery and the product in which it is

inserted are not compatible. Consult Hilti Service.

One (1) LED quick-flashes red| The Li-ion battery is locked and cannot be used.

Consult Hilti Service.

Indicators showing the battery’s state of health
To check the battery’s state of health, press the release button and hold it down for longer than three seconds. The system does not detect a potential malfunction of the battery due to misuse, for example, the battery dropped or pierced, external heat damage, etc.

All LEDs show in sequence, followed by one (1)

LED showing constantly green.

| The battery can remain in use.
All LEDs show in sequence, followed by one (1) LED quick-flashing yellow.| The check to ascertain the battery’s state of health did not completed. Repeat the procedure, or consult

Hilti Service.

All LEDs show in sequence, followed by one (1) LED showing constantly red.| If a connected product can still be used, the re- remaining battery capacity is below 50 %.

If a connected product can no longer be used, the battery has reached the end of its useful life and

has to be replaced. Consult Hilti Service.

Technical data

(4.9 lb)

Ambient temperature for operation| −17 ℃ … 60 ℃

(1 ℉ … 140 ℉)

Storage temperature| −20 ℃ … 70 ℃

(−4 ℉ … 158 ℉)

Battery

instructions

Ambient temperature for operation| −17 ℃ … 60 ℃

(1 ℉ … 140 ℉)

Storage temperature| −20 ℃ … 40 ℃

(−4 ℉ … 104 ℉)

Battery charging starting temperature| −10 ℃ … 45 ℃

(14 ℉ … 113 ℉)

Blade
Blades of different types are needed, depending on the thickness or strength of the material to be cut. Select the correct blade for the purpose from the table below. The blades have two cutting edges. The cutting edges cannot be resharpened. Initial equipment, as supplied ex works: SSH­CS 1.5 ­ 2.5 mm or SSH­CD4 mm × 0.9 mm

Preparations at the workplace

WARNING
Risk of injury by inadvertent starting

• Before inserting the battery, make sure that the product is switched off.
• Remove the battery before making any adjustments to the power tool or before changing accessories.
• Observe the safety instructions and warnings in this documentation and on the product.

Charging the battery

1. Before charging the battery, read the operating instructions for the charger.
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
3. Use an approved charger to charge the battery. → page 6

Inserting the battery

WARNING
Risk of injury by short circuit or falling battery

• Before inserting the battery, make sure that the contacts on the battery and the contacts on the product are free of foreign matter.
• Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.
2. Push the battery into the product until it engages with an audible click.
3. Check that the battery is seated securely.

Removing the battery

1. Press the battery release button.
2. Remove the battery from the product.

Fall arrest

WARNING
Risk of injury by falling tool and/or accessory

• Use only the Hilti tool tether recommended for your product.
• Prior to each use, always check the attachment point of the tool tether for possible damage. Comply with the national regulations for working at heights.
• As a drop arrester for this product, use only a combination of the Hilti retaining strap and the Hilti tool tether #2261970.
• Secure the retaining strap to the installation openings for accessories. Check that it holds securely.
• Secure one carabiner of the tool tether to the retaining strap and secure the second carabiner to a load-bearing structure. Check that both carabiners hold securely.
• Comply with the operating instructions of the Hilti retaining strap and those of the Hilti tool tether.

Setting the cutting speed

• Set the cutting speed by turning the adjusting knob for motor speed.

Changing the blade

CAUTION
Risk of injury! The accessory tool may be hot and/or have sharp edges.

• Wear protective gloves when changing the accessory tool.
• Never lay down a hot accessory tool on a flammable surface.

CAUTION
Risk of damage to workpiece and blade
Always select the correct blade for the planned use and thickness of the material to be cut.

Change the blade when it becomes blunt and cutting performance diminishes. Always replace the blade whenever you install new cutting rails.

1. Press out the bearing pin.
2. Pull the blade out of the cutting head.
3. Lightly grease the bearing pin and the new blade.
4. Insert the new blade.
5. Push the bearing pin into the hole until it engages.

Changing the cutting rails

CAUTION
Risk of injury! The accessory tool may be hot and/or have sharp edges.

• Wear protective gloves when changing the accessory tool.
• Never lay down a hot accessory tool on a flammable surface.

CAUTION
Risk of damage to product and cutting tools

• Clean the threads before installing the securing screws.
• Always use the new securing screws supplied and tighten the screws to the specified tightening torque.

1. Remove the securing screws and remove the cutting rails. If necessary, insert a suitable tool through the cutting head from above and push the cutting rails out of the guide.
2. Clean the thread.
3. Check the cutting rails:

• If the cutting rails are blunt along only one half, reinstall them turned through 180°.
• When either one of the two cutting rails is blunt along with both halves, replace the two cutting rails as a pair.
• Insert the cutting rails and install the securing screws.

Technical data

Tightening torque| 5 Nm

(4 ftlbf)

Changing the cut-off plate

CAUTION
Risk of damage to product and cutting tools

• Clean the threads before installing the securing screws.
• Always use the new securing screws supplied and tighten the screws to the specified tightening torque.

1. Remove the securing screw and remove the cut-off plate.
2. Clean the thread.
3. Insert the new cut-off plate and install the new securing screw.

Technical data

Tightening torque| 5 Nm

(4 ftlbf)

Operation
Observe the safety instructions and warnings in this documentation and on the product.

Switching on

• Press the rear section of the on/off switch.
• Slide the on/off switch forward.
• The motor runs.
•  Lock the on/off switch.

Cutting

Before starting work, check that the cutting rails and the cut-off plate are correctly and securing seated and check the tightening torques of the corresponding securing screws.

1. Switch the tool on. → page 11
2. Guide the product through the material to be cut while holding the product at an angle of about 14 ° to the material.

Always use a sharp blade and turn or change the cutting rails in good time. Apply cutting oil or another cooling lubricant to the workpiece to prolong the useful life of the cutting tools.

• If the following conditions are met, also take this action: Conditions: Cutting curves
• Guide the product slowly through the material, following the applicable radius. Do not tilt the product to the side.
• To end the cut, switch the product off.

Cutting off swarf

Do not cut off short lengths of swarf. The minimum length of the strip of swarf cut-off must be one complete curl. Marks on the front of the housing indicate the cut-off position.

1. With the product switched on, press the swarf cutter for 0.5 a second.
2. The strip of the swarf is cut off at the mark and the cut-off process stops automatically.
3. Remove the cutting of the swarf by hand.

Switching off

• Press the rear section of the on/off switch.
• The on/off switch jumps into the off position and the motor stops.

Care and maintenance

WARNING
Risk of injury with the battery inserted Always remove the battery before carrying out care and maintenance tasks

Care of the product

• Carefully remove stubborn dirt.
• Carefully clean the air vents, if present, with a dry, soft brush.
• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as these can attack the plastic parts.
• Use a dry, clean cloth to clean the contacts of the product.

Care of the Li­ion batteries

• Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.

• Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of moisture (e.g. by being dipped in water or left in the rain).
  If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable container and consult Hilti Service.

• Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents containing silicone as these can attack the plastic parts.
  Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts.

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as these can attack the plastic parts.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all function correctly.
• Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product repaired by Hilti Service.
• After cleaning and maintenance, install all guards and protective devices and check that they are in full working order.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables, and accessories approved by Hilti for use with your product can be found at your Hilti Store or online at: www.Hilti.group

Transport and storage of cordless tools and batteries Transport

CAUTION
Accidental starting during transport Always transport your products with the batteries removed

• Remove the battery/batteries.
• Never transport batteries lose and unprotected. During transport, batteries should be protected from excessive shock and vibration and isolated from any conductive materials or other batteries that may come in contact with the terminals and cause a short circuit. Comply with the locally applicable regulations for transporting batteries.
• Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged batteries.
• Prior to each use and before and after prolonged transport, check the product and the batteries for damage.

Storage

WARNING
Accidental damage caused by defective or leaking batteries Always store your products with the batteries removed

• Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in the technical data.
• Do not store batteries on the charger. Always remove the battery from the charger when the charging operation has completed.
• Never leave batteries in direct sunlight, on sources of heat, or behind glass.
• Store the product and batteries where they cannot be accessed by children or unauthorized persons.
• Prior to each use and before and after prolonged storage, check the product and the batteries for damage.

Troubleshooting

If a problem occurs, always observe the status indicator of the battery. See the section headed Status indicators of the Li­ion battery. If the trouble you are experiencing is not listed in this table or you are unable to rectify the problem by yourself, contact Hilti Service.

The battery runs down more

quickly than usual.

| Very low ambient temperature.| ▶ Allow the battery to warm up

slowly to room temperature.

The battery does not engage

with an audible click.

| The retaining lug on the battery is

dirty.

| ▶| Clean the retaining lug and

re-insert the battery.

The product or battery gets very hot.| Electrical fault| ▶ Switch the product off immediately, remove the battery, keep it under observation,  allow  it to cool down and contact Hilti

Service.

The motor has no braking effect.| The battery is discharged.| ▶ Change the battery and charge

the empty battery.

The product is momentarily

overloaded.

| ▶ Switch the product off and then

on again.

The product does not develop fully

power.

| A battery with inadequate capacity

was used.

| ▶| Use a battery with adequate

capacity.

Diminishing cutting performance| Blade and/or cutting rails are blunt.| ▶| Change the blade. → page 10
▶| Change the cutting rails.

→ page 10

LEDs of the battery show

nothing

| The battery is defective.| ▶ Contact Hilti Service.

Disposal

Risk of injury due to incorrect disposal! Health hazards were due to escaping gases or liquids.

• DO NOT send batteries through the mail!
• Cover the terminals with a non-conductive material (such as electrical tape) to prevent short-circuiting.
• Dispose of your battery out of the reach of children.
• Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public health and safety resources for disposal instructions.

Most of the materials from which Hilti products are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries,
your old tools, machines, or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information.

• Do not dispose of power tools, electronic equipment, or batteries as household waste

Manufacturer’s warranty

• Please contact your local Hilti representative if you have questions about the warranty conditions.

Further information

For more information on operation, technology, environment, and recycling, follow this link: qr.hilti.com/manual/?id=2331869 This link is also to be found at the end of the documentation, in the form of a QR code.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>