MUSICIAN Draco R2R DAC HiFi Entry-Level Decoder User Manual
- June 5, 2024
- MUSICIAN
Table of Contents
MUSICIAN Draco R2R DAC HiFi Entry-Level Decoder User Manual
Introduction
Thank you for choosing MUSICIAN products!
Guangzhou LEZHIJIA Technology Co.,Ltd.(MUSICIAN Audio) was formally established in 2020. The R & D team is formed by a group of enthusiasts with more than 20 years of audio research and development experience. It is committed to the following prod uct: R2R discrete balanced decoders, balanced headphone amplifiers, balanced amplifiers, balanced pre-amplifiers, headphones, passive speakers, and other audio products.
Tips
- Do not cover newspapers, tablecloths, curtains, etc. on the machine, as this may prevent heat dissipation. If the temperature inside the machine is too high, it may cause a fire, damage the machine, or cause personal injury. When using switches, knobs or cables, do not use excessive force.
- Only use the voltage specified by this machine. Using a voltage higher than the specified value is dangerous and may cause fire, damage to the unit, or personal injury.
- Do not attempt to modify or repair this unit by yourself. If you need any service, please contact the MUSICIAN after-sales team through the official website.
- If you plan not to use the machine for a long time, disconnect the power cord from the AC wall outlet. To strengthen the protection of this product, unplug the power cord from the wall outlet during lightning, or when no one is managing it, and when not using it for a long time. This will prevent the product from being damaged during lightning and power grid surges.
Front and rear panels
- Input Source Selection
- Switch/Standby
- NOS Button
- XLR Balanced output
- RCA Output
- I2S Input
- COAX Input
- OPT Input
- USB Input
- AES Input
- Power Switch
- Power Input
Product information
DRACO Features R2R DAC
R2R Array DAC True Balance, R—2R network control decoding linear error, high
decoding speed, low digital noise, not only to ensure low distortion of the
audio signal, but also to ensure very low background noise music.
Self—Developed Technology, Using self—developed and designed digital filters,
which can greatly increase dynamic contrast, analysis, and more natural and
delicate timbre, etc.
Multiple ports and multiple options, Digital input has I2S, Coaxial, Optical,
AES Balanced, USB. Analog output has a set of XLR balanced output and a set of
RCA output.
Using the main control ALTERA high—efficiency chip, the audio signal
transmission is not distorted
Packaged Linear Power Supply, ensure low noise and stable power supply voltage
for the DAC.
Machine aging
The burn—in time of Draco DACs is one week: Standby or Powered on 24/7 (300 hours), you will get the best performance after the enough aging hours.
Connecting RCA or XLR output simultaneously is not recommended, it will degrade the sound quality because they are shared. Even if the downstream equipment is on/off, the output signal will still be transmitted to the input stage of the downstream device.
If possible, please use the XLR output. As a true balanced DAC, the XLR output
of Draco will be more superior.
Basic Parameters
Function keys: Input source selection, Switch/Standby, NOS, Mute, Mode
Input mode: I2S, coaxial, optical fiber, AES, USB
Output mode: XLR, RCA
Power input: 115v—230v (50 / 60Hz)
Bare machine size: 250mm265mm55mm(WDH)
Bare metal weight: 3.6KG
Packing weight: 4.25KG
Packing list
- Aquarius *1
- AC Power Cable *1
- User Manual *1
- Warranty card *1
Operating Instructions
Power on and standby
Connect the power, turn on the DAC by short pressing the middle power button ,
LED light is off at this time. If you press again, the DAC will to standby
mode and the LED lights up.
Signal input selection
The left side of the front panel is the input mode selection, you can switch
the input mode freely by pressing the INPUT button
Select COAXIAL as input, the LED above the corresponding COAX lights up;
Select OPTICAL as input, the LED above the corresponding OPT lights up;
Select AES as input, the LED above the corresponding AES lights up;
Select USB as input, the LED above the corresponding USB lights up;
Select 125 as input, the LED above the corresponding I2S lights up.
NOS
NOT Indicator light off means oversampling; NOT Indicator light on means
original sampling rate.
Analog audio signal output
Two output modes: XLR balanced output and RCA output.
Digital audio signal input
Five input methods: I2S, COAXIAL, OPTICAL, AES and USB.
AC power input
AC power requirements: 115-230v (adjustable), 50/ 60Hz
Drive installation
- Please visit the official website of MUSICIAN and download the ( http://www.musician-audio.com/en/col.jsp?id=105 ) Download the DRACO driver: “ DRACO drive. Zip ”.
- Connect the device with the computer by USB cable→ turn on the device→ short press “ Input ” to switch to the USB input mode.
- Open the downloaded DRACO file→ click setup to start the installation→ continue to click “ Next ”→ until the installation is complete and show “ Finish ”.
- After installation , in the right corner of the computer→ Click on the playback device select “ MUSICIAN USB DAC ” the as the default device
Drive installation finished
I2S Pin Configuration of DRACO
PS: There is no industry standard of I2S connection. Different brand/product has different l2S line order.
MUSICIAN Draco is trying to compatible with most of device by the following
mode setting method if you are using standard HDMI cable:
- Select the sound source input to 125;
- Press the switch/stand by button in the middle (the lights on);
- Press NOS button, and the 125 lights on at the same time;
- Press the switch/stand by button in the middle again (the lights off);
- Press the NOS button to cycle through the phase modes (there are total 8 modes, 1X, 2X, 4X indicator lights are binary mode Display);
- Stop the operation when you selected the satisfied sound, the machine automatically exits the mode setting function
Through the above I2S settings, Draco can basically meet most of the brands on the market.
If it can not playing properly(such as hiss sound) by the above setting. This shall not be considered as a defective product, but just a matching failed. The suggested solution is to use a customized HDMI cable(The pin layout is on the right).
Warranty
We take pride in the quality of our products with strict quality control checks.
To give you more confidence, all of our products are provided with a three- years warranty. Within the first 30 days from the date of purchase, most items can be returned for refund or exchange if meet the following conditions. Wish you enjoy a wonderful shopping experience!
RETURNABLE ITEMS
Items that can be returned/refunded or exchanged within 30 days of receipt must comply with the following standards
- Any returned items must be accompanied by all accessories, hardware, manuals or instructions, and in the same “new” state as when shipped to you.
- Any returned items will be evaluated after receipt. Of course, we will not refund any defective products caused by improper handling, improper use, tampering or improper use.
- If there is no complete original packaging(original packing box, foam filling, etc.) at the time of return, 25% replenishment fee will be charged.
Tips: The items should be transported back safely. Before we received,
You will take full responsibility. If you choose to replace, we will ship your
replacement items free of charge.
RETURN FEE AND ADDRESS
We aim to provide services that benefit all our loyal customers.
Global customers can return products to our Chinese warehouse.
Please always contact us before returning items to relevant addresses.
- All transportation costs are borne by the customer. This includes shipping costs for returns or exchanges. Shipping costs are non-refundable.
- Please contact your local post office to confirm the actual return shipping fee before shipping back. We recommend that you use the cheapest postal service if available.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>