PEHRATEK PRODUCTS XM-5000 Wireless/Wired VRA System Instruction Manual

PEHRATEK PRODUCTS XM-5000 Wireless/Wired VRA System

PACKAGE CONTENTS

• 2-Rectangular Plexiglass Boxes
• 1–Wireless Remote Control (REM-5000)
• 2– DC 9 Volt Power Adapter (ADA-13)
• 1-Power Split(er Y-Cord (CAB-66)
• 2-14’ Exten Power Cables (CAB-010)
• 1-RF RECEIVER MODULE
• 2-3.5mm M-M Cable 12 Foot (CAB 012)

STEP ONE: Position each Reinforcer box over or near the le< and right sound field speakers. Moun8ng these boxes to the wall of the sound room can be done by one of these four options:

1. Using op8onal Dual Arm mounting brackets (DUA-001)
2. Using self-tapping screws through predrilled holes on the back of the box
3. Use Velcro or double back tape to mount to top of loudspeakers.
4. Use op8onal corner mounting brackets (INS-KIT2) for moun8ng boxes in the corners of the sound booths.

STEP TWO: Insert cables for power into bo(om of each VRA box connector block. (See LEGEND) Insert 3.5mm cables from RF RECEIVER MODULE, into IR SENSOR (blue) jack underneath each reinforcer box.
STEP THREE: Mount the centering box in between units onto a wall using self-tapping screws through the eyelet holes in the back of the box or double back tape to hold into position.

LED BLINKS WHEN CONNECTED & ACTIVATED

• Volume can only be adjusted when unit is not activated.

OPTIONAL ACCESSORIES

• DUCK CENTER BOX LPC-200
• MOVING DOG CENTER BOX (LPA-600)

NEW ELITE VRA+SPEAKER

• XM-5000 VRA SLIDES INTO SPEAKER CHANNEL CAN BE MOUNTED ON TOP OR BOTTOM SPACE-SAVING SLEEK WOODEN DESIGN FOAM GRILL CAN BE CLEANED.

CORNER MOUNTING BRACKET/INSTALLATION KIT (INS-KIT2)

• INTERCHANGEABLE TOY KIT (TOY-022) 6 Toys.

REMOTE CONTROL OPERATION

SOUNDS

1. Monkey
2. Cartoon Laugh
3. Boing
4. Tuba
5. Goofy Laugh
6. Duck
7. Hyena
8. Chipmunk
9. Rooster
10. Kid Laughing
11. Mute

LIGHT PATTERNS

1. Marquee Dot
2. Marquee Bar
3. Marquee-Segment
4. All On Flashing
5. Blinking Random

MOTION

1. Back & Forth
2. Stutter Swing
3. Shift-Shift-Back
4. No Motion

NOTE: Pattern Light blinks when the signal is being sent from the remote when depressing the RIGHT/LEFT/CENTER buttons.

TROUBLESHOOTING

CONNECTOR BLOCK

• (Can use Y-CORD (CAB-66) from one Power Pack to operate both units)
• Use Power Extension Cables to lock into the jack.

• Volume can only be adjusted when the unit is not activated.

NOTE: POWER ON RED LED IS INSIDE BOX ON BACK PC BOARD.

HOW TO CHANGE RF CHANNELS

NOTE: Always power cycle the remote and VRA boxes after changing channels.

TROUBLESHOOTING

• Volume can only be adjusted when the unit is not activated.
• Buttons are located at bottom of the unit.

FCC

Per FCC 15.19(a)(3) and (a)(4) This device complies with part 15 of the FCC Rules. Opera8on is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera8on. FCC 15.21, The user manual or instruc8on manual for an inten8onal or uninten8onal radiator shall cau8on the user that changes or modifica8ons not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>