HOROW HR-0033U Dual Flush Round Toilet Instructions

HOROW HR-0033U Dual Flush Round Toilet

Instructions

TOOLS AND MATERIALS REQUIRED

• Water Supply Kit (Not needed if replacing existing toilet)
• Adjustable Wrench
• Flathead Screwdriver
• Level
• Nut Driver or Socket Set
• Putty Knife
• Tape Measure

REMOVING YOUR OLD TOILETIDEHONTAGE

1. Turn off the water supply.
2. Flush the toilet to empty the tank. Remove any water left in the tank or bowl
3. Disconnect the supply line from the tank. Remove decorative caps. Unscrew nuts that attach the toilet to the floor.
4. Remove toilet.
5. Make sure the water supply valve is shut off before installation.
6. Remove old closet bolts from the closet flange. Clean any old wax, putty, etc. from the base area.

IMPORTANT NOTE REGARDING WATER SUPPLY
Before installation ensure that the shut-off valve is greater than 7%” from the center of the drain to the center of the shut-off valve on either side (Figure 1).

NOTE: This is a true 12″ rough-in toilet from the finished wall to the center of the drain (no less than 12″). Baseboard thickness may reduce rough- in dimension.

ONE-PIECE TOILET

1. Install new floor bolts into the floor flange.
2. Attach flexible water supply line to the inlet of the fill valve and hand tighten only. At this point, DO NOT connect to the water shut-off valve.
3. Place a new wax ring around the waste flange of a toilet bowl.
4. Lower the toilet onto the closet bolts, so the bolts project through mounting holes in the base of the toilet. Using a rocking motion, press the bowl down to position the toilet
5. Install plastic cap washers, followed by metal and nuts onto the closet bolts. Tighten the bolts alternately until the toilet is firmly seated on the floor.
6. Install plastic cap covers
7. Connect the flexible water supply line (not included) to the shut-off valve. Tighten the coupling nut securely

WATER SUPPLY

• Turn on the supply valve and allow the tank to fill until the float rises to shut off position.
• Check for leakage at fittings, tighten or correct as needed.

TWO PIECES TOILET

INSTALLATION PROCEDURE

1. Install new closet bolts into the closet flange. (Figure8) You can pre-cut the closet bolts to the desired length to put on the bolt cap by doing the following: Temporarily install closet bolts and set the toilet and place the washers and nuts onto the bolts. Then mark the length needed. Take the toilet out of the place and remove the closet bolts. Cut the closet bolts to the length and then turn the toilet upside down onto a soft surface to avoid scratches on the finish.

2. Place a new wax ring around the waste flange of the toilet bowl.

3. Lower the toilet onto the closet bolts, so the bolts project through mounting holes in the base of the toilet

4. Using a rocking motion, press the bowl down to position the toilet install plastic cap washers, followed by meta. I washers and nuts onto the closet·bolts. Tighten the bolts alternately until the toilet is firmly seated on the floor.
   CAUTION: DO NOT OVERTIGHTEN NUTS, SEVERE DAMAGE MAY OCCUR DOMMAGES GRAVES. Install the flange bolt caps.

5. Insert tank bolts inside the tank. Use the metal and rubber washers supplied to create a seal.

6. Install the metal nut and washers on the bolts under the tank. Tighten the nuts until the rubber washers in the tank create a proper and secure seal.

Attach the large rubber sealing gasket to the center drain hole under the tank.

Gently place the tank on the bowl with the bolts protruding out underneath. Then tighten with metal oval washers and wing nuts, tighten enough that the tank sits flat on the bowl. Make sure that the toilet tank is parallel to the wall and straight on the bowl

CAUTION: DO NOT OVERTIGHTEN NUTS, SEVERE DAMAGE MAY OCCUR.

CONNECT WATER SUPPLY

1. Connect water supply line (new or existing) between the shutoff valve and tank inlet water fitting. Tighten coupling nuts securely.
   NOTE: DO NOT OVERTIGHTEN

2. Turn on the supply valve and allow the tank to fill until float rises to shutoff position.

3. Check for leakage at fittings, tighten or correct as needed.

TANK FITTING INSTALLATION & ADJUSTMENT PLEASE REFER TO THE INSTRUCTION MANUAL PUT INSIDE THE TANK. TOILET SEAT INSTALLATION INSTRUCTION

Installation Guide

1. Insert revolver, washer, and bolt into the installing hole.
2. insert the nut into the two holes perfectly and screw it

Above locked

1. Place the toilet seat cover on the bowl and insert the bolt. washer and rubber cord in hinge install hole-order;
2. Adjust the position of the toilet seat cover to match the toilet set suitably after inserting the rubber cord into the toilet install hole
3. Tighten the bolt and close the hinged cover;
4. insert the nut into the two holes perfectly and screw it with a screwdriver then put the cap on it.

Instructions

Please abide by the following illustrations to ensure safety Please read carefully the relative notice before operation. This manual lists many kinds of marks in detail to avoid injuring the body. or suffering loss on the property. The marks and explanations are as follows, please keep them in the eyeable place

• Do not stand on the toilet cover and do not place heavy objects on it. (Or else it may cause a crack.)
• Do not clean the toilet seat with household cleaners, volatile, thinner, and eradicator, or use a nylon brush, and avoid chlorine-containing. corrosive and abrasive cleaners.
• Maintain the shiny surface by using soft fabric and clean water. (Or else it may cause abrasion or crack. 

Relative Notice

• Open and close the toilet seat cover tenderly
• Avoid sunlight and other lamp-house irradiate directly.
• Please open the toilet seat and cover it completely the function of slow closing will fail off in the midway.or hurt fingers etc.

Maintenance

1. Periodical maintenance
   • Wipe gently with a wet fabric.
   • Wipe off smut
   • Wash it with neuter cleaners(such as soap powder) and then dry it with a clean fabric.
2. Cleaners
   • Do not wipe and wash the toilet seat and cover with abrasive powder.
   • Do not use a disinfector, eradicator, or other aerosol cleaners.
   • Some chemicals and cosmetics in the bathroom may damage the toilet seat and cover.

TROUBLESHOOTING

• Problem: Poor Flush, the water level is below the water line mark.
• Solution: The shut-off valve is not completely open; verify that the shut-off valve opens fully. The water supply line can be twisted, ensure that it is sitting in the tank properly. For two pieces toilet, also need to verify if the chain is too long or the flapper is not lifting properly to activate the flush
• Problem: Continuous water running. Solution: It may occur if the flush seal is not completely closed.

1. Verify if there is any obstruction with the flush seal.
2. For the one-piece toilet, also need to make sure the flush valve chain has the proper length at rest.

NOTE: IMPROPER CARE MAY CAUSE THE WARRANTY TO BECOME INVALID.

LIMITED WARRANTY

We warrant its products to be free from defects in material or workmanship for 1 year (Vitreous China) and 1 year (Parts and Fittings) from the date of purchase of the product by the original purchaser. If inspection of this plumbing product, within 1 year (china product) or 1 year (parts and fittings) after its initial purchase, confirms that it is defective in materials or workmanship, we will repair or at its option, exchange the product for a similar model. We provide no warranties or guarantees beyond those in this Limited Warranty. This limited warranty applies only to the original purchaser and installation of these products. All de-installation and re-installation and transportation costs or charges incidental to warranty services are to be borne by the owner. In no event will we be liable for the cost of repair or replacement of any installation materials, including but not limited to, tiles, marble, etc. We will not be responsible for and this warranty does not cover and specifically excludes any liability to the purchaser or any third party for consequential or incidental damages, au of which are hereby expressly disclaimed, or the extension beyond the duration of this warranty of any implied warranties, including those of merchantability or fitness for an intended purpose. This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation. We shall not be responsible or liable for any failure or damage to its toilet tank trim, plumbing fittings, or china products caused by the use of either chloramines or high concentration of chlorine, lime/ iron sediments, and/or other minerals not removed from public water during the treatment of public water supplies or caused by toilet tank type cleaners containing chlorine, calcium hypochlorite, and I or other chemicals. This warranty is void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident, or other damages; if it was not installed in accordance with our instructions; or if it has been modified in a manner inconsistent with the product as shipped by us.

Note: Some states or provinces do not allow the limitations on an implied warranty, and some states/provinces do not allow exclusions or limitations regarding incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may have other rights, which vary from state to state or province to province. No person is authorized to change, add to, or create any warranty or obligation other than that set forth herein. This warranty gives the original purchaser of this product-specific legal right, which may vary from state to state or from province to province. In some states or provinces, the exclusion or limitation of incidental or consequential damages is not allowed, so those exclusions may not apply to you.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>