MINISFORUM U850 New Gen DeskMini Computer User Guide
- June 5, 2024
- MINISFORUM
Table of Contents
New Gen DeskMini Computer
Basic Operation
Button & Ports
01
The power button allows you to power ON/OFF the Mini PC. You can use the power
button to put your Mini PC to power saving mode or press it for ten (10)
seconds to force shutdown your Mini PC.
02
Headphone/Headset/Microphone Jack
This connector is used to connect audio output signals to a power amplifier or
headphones.You can also use it to connect an external microphone or output
signals from audio equipment.
03
USB 3.0 Gen 1 Port
The USB 3.0 Gen 1 (Universal Serial Bus) port provides a transfer rate up to
5.0 Gbps.
04
USB-C Port
- The USB-C(Universal Serial Bus-C)interface provides a transmission rate of up to 5.0 Gbps and supports 4K©60Hz display output.
- Support DC power input and provide power to Mini PC,the input voltage is 19V.
05
Reset Hole
Please connect the power, press and hold the reset hole for ten (10) seconds,
and the BIOS will return to the factory default value settings.
Important! If you encounter some problems during use, you can first try
to solve it by pressing the reset hole.
06
USB 3.0 Gen 1 Port
The USB 3.0 Gen 1 (Universal Serial Bus) port provides a transfer rate up to
5.0 Gbps.
07 DP
DisplayPort
This DisplayPort supports display output at 4K@60Hz, add support for HD audio
signal transmission while transmitting video signals, which provides a common
data connection channel for compatible devices (such as set-top boxes,
integrated amplifiers, digital audio or televisions).
08 HDMI
HDMI Port
HDMI (High-Definition Multimedia Interface) connector and is HDCP compliant
for HD DVD, Blu-ray, and other protected content playback.
09
LAN Port
This RJ-45 network interface supports standard Ethernet cables and can be
connected to a local area network.
10 2.5G LAN
LAN Port
This RJ-45 network interface supports standard Ethernet cables and can be
connected to a local area network. (Transmission speed 2.5Gbps)
11
Kensington Lock
The Kensington Lock can be connected to a locker to prevent others from
stealing your Mini PC.
12
Power Input
The supplied power adapter can convent AC power to DC power for use, and
supply power through this jack to the Mini PC. To prevent damage to your Mini
PC, please use the supplied power adapter.
Warning! When the power supply is in use, the temperature of the power
adapter may rise and become hot. Do not cover the power adapter or get close
to you. Power adapter: DC 19V
13
Air Vents
These vents let hot air out of the Mini PC case.
Important! Do not allow paper, books, clothing,trans-mission lines, or
any other objects to blockany vents, as this may cause the machine to
overheat.
Getting started
1
Connect a display panel to your Mini PC by connecting a display cable either to the HDMI port , DisplayPort or the USB-C port
2
Connect keyboard and mouse
3
Connect Mini PC with power adapter
4
Power On
User Operation Guide
Installation Operation
1
Press the positions as shown with your hands to loose the top cover
2
Remove the top cover
DIY DDR
3
Install the Memory into the SODIMM Slot by inserting it slantly into the buckles on both sides and fix it
DIY SSD
4
Install the SSD into its slot by inserting it slantly and fix it with screws
DIY HDD
5
Screw out the screw,take out the hard disk box and install the hard disk (as shown in the figure)(Note:HDD cannot exceed 7mm)
6
Fix the hard disk with screws and fix the hard disk case (as shown in the figure)
7
Direct the buckles of top cover to their slots,and cover the case
8
Press the positions as shown with your hands to fasten the top cover
VESA
Mount Your Mini PC to a VESA Compatible Device
Please follow the steps below to install the Mini PC to a compatible VESA
compatible device:
-
Install the VESA Mount on the back of the device with the included screws. (A)
-
Place Mini PC upside down on a flat and stable surface and install the included screws to the screw holes of the bottom of the Mini PC.
Warning! Do not over tighten the screws as it may damage to your Mini PC. -
Fix the Mini PC to the VESA Mount of the monitor (B)
Precautions for use
- Please carefully read all the instructions on the manual before using the product.
- The system is installed as a clean version.
- Do not use this product near water or a heat source.
- Make sure you leave plenty of space around the system for ventilation.
- Please make sure to leave enough space around the product for ventilation, and never insert any object into the air vents.
- Use this product in environments with ambient temperatures between 5°C and 35°C.
- If you use an extension cable, make sure that the total amperage of the devices plugged into the extension cable does not exceed its ampere rating.
- The product should be installed and operated with a minimum distance of 20cm from you.
Care during use
- Do not step on the power cord or leave anything on your Mini PC.
- Do not spill water or any other liquids on the product.
- It still has a tiny mount of current when you turn off the product.
- Before cleaning the product, please make sure unplug the power adapter.
- If you encounter a technical problem of the product, please unplug the power adapter and contact our technical support or customer service.
Package contents
Power Adapter Power Cable HDMI Cable
VESA Mount Screw Set VESA Mount Technical Documents
- The power adapter included in the box will vary depending on the model and region you purchased.
Contact information
Address 19H Maxgrand Plaza, No.3 Tai Yau Street, San Po Kong, Kowloon Hong
Kong
TEL 00852-30506835
Online Technical Support
Support https://www.minisforum.com/support
https://www.minisforum.jp/support
Email support@minisforum.com
Official Web http://www.minisforum.com
Official Web http://www.minisforum.jp
Each Mini PC has its unique SN code, which is at the bottom of the product. When you need our after-sales support, just provide us the SN code to ensure that you could enjoy our quick and accurate service.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>