JAMARA 153075 X Peak Touch USB 2L Charger Instruction Manual

: June 5, 2024
: JAMARA

Table of Contents

JAMARA 153075 X Peak Touch USB 2L Charger
General information
Technical data
Highlights
Special features
Connections and Controls
Main Screen
Initial parameter setup
Getting started to balancing charging/charging/discharging and cycles
Battery‘s Doctor Progam
Warning and error information
Additional information
Safety Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

JAMARA 153075 X Peak Touch USB 2L Charger

General information

JAMARA e.K. is not liable for any damage caused to the product itself or through this, provided this is due to improper operation or handling errors. The Customer alone bears the full responsibility for the proper use and handling, including without limitation, the assembly, the charging process, the use and choice of the operation area. Please refer to the operating and user instructions, it contains important information and warnings.

Certificate of Conformity
Hereby JAMARA e.K. declares that the product „Charger X-Peak Touch USB 2L, No. 153075“ complies with Directive 2014/30/EU, 2014/35/EU and 2011/65/EU.
The full text of the EU Declaration of Conformity is available at the following Internet address: www.jamara-shop.com/Conformity

WORNING
Read the complete instructions and security instructions carefully before using the model.
Caution! Please fully and carefully read warnings/ safety instructions. These are for our own security and can avoid accidents/injuries.

Technical data

Input
AC 100 – 240 V; 50 Hz; 0,80 – 0,33 A; 84 W DC 11 – 18 V; 7,2 – 4,5 A; 80 W
Output
LiIon/LiPo/LiFePo: 1 – 6
NiCd/NiMH: 1 – 16
Pb 2 V ~ 20 V
Charging current
max. 80 W, 0,1 ~ 10,0 A
Discharge current
max. 10 W, 0,1 ~ 2,0 A
Balance current
450 mAh/cell
Discharge
2,0 – 4,2 V/Cells Li-Ion, LiPo, LiFePo
Dimensions
180 x 145 x 60 mm
Weight
650 g

Highlights

Touch Screen
Dual Power Built-in AC Adapter 230V and 12V
Internal independent lithium battery balancer
Individually balanced battery discharge
Adaptable for various type of lithium battery
Maximum safety
Automatic charging current limit
Input power monitoring
Capacity limit
Temperature monitoring with programmable switch-off
Proscessing time limit
Load capacity display
Supports Lithium, NiMh, NiCd and Lead battery packs
Graphical display of each individual cell level
Internal resistance measurement of each individual Lithium Battery cell
Servo Tester
18 individual configurable presets
Monitored USB charging port. For example, for charging cameras, smart phones etc.
Simultaneous charging on USB charging port and main
Adjustable power supply function output 1 – 28V

Box content

Charger
Extension lead: Electric cable 230 V and 12 V (for car battery)
Charging lead: LiPo Deluxe
Instructions

Accessories:

Balancer Adapterboard Universal
No. 15 3043
Adapter cable Balancer Universal
No. 15 3044
Temperature sensor
No. 15 3056

Special features

Internal independent lithium battery balancer
The Charger has an integrated balancer connection for the included Balander board (up to 6-cell lithium) (Optional Universal Balancer Board, No.153043, balancer adapter cable, No. 153044). It isn‘t necessary to connect an external balancer for balance charging.

Balancing individual cells battery charging/discharging
During the process of discharging, the charger can monitor and balance each cell of the battery in-dividually. Error message will be indicated and the process will be ended automatically if the voltage of any single one cell is abnormal.

Adaptable to various type of lithium battery
The charger is adaptable to various types of Lithium batteries, such as Li- ion, LiPo and the new LiFe series of batteries.

Maximum safety
Delta-peak sensitivity: the automatic charge termination program based on the principle of the Delta-peak voltage detection. When the battery‘s voltage exceeds the threshold, the process will be ter-minated automatically.

Automatic charging current limit
You can set up the upper limit of the charging current when charging your NiCd or NiMh battery. It is useful for the NiMh battery of low impendance and capacity in the „Auto“ charging mode.

Input power monitoring

To portect the car battery used as DC input power from being damaged, its voltage keeps being monitored. If it drops below the lower limit, the process will be ended automatically.
Temperatur monitoring with programmable cut-off
The battery‘s internal chemical reaction will cause the temperature of the battery to rise. If the tem-perature limit is reached, the process will be terminated.
This function is available by connecting optional temperatur probe (Ord. No. 153056), which is not included in our package.

Capacity limit
The charging capacity is always calculated as the charging current multiplied by time. If the charging capacity exceeds the limit, the process will be terminated automatically when you set the maximum value.

Processing time limit
You can also limit the maximum process time to avoid any possible defect.

Cyclic charging/discharging
1 to 5 cyclic and continuous process of charge>discharge or discharge>charge is operable for bat-tery refreshing and Balancing to simulate the battery‘s activity. JAMARA 153075 X Peak Touch USB 2L Charger FIG
1

Connections and Controls

230 V AC Input
USB charging socket
10 – 18 V DC Input
emperature sensor socket USB-JR socket
Servo socket
Cooler
Charge cabel sockets
red = plus (+)
black = minus (-)
Balancer sockets (1 – 6)
LED screen with Touch screen and light

Using your charger for the first time
The Charger is fitted with 2 power inputs which gives you the choice of powering the unit from the household mains supply (220 V AC) or via 12 V DC. The 12 V DC can be either a vehicle battery or a stabilised transformer.
Connect the charger to an input of your choice, if using 12 V pay particular attention to the polarity. The red crocodile clip must be connected to the plus pole (+) and the black clip to the minus pole (-). After connection Info menu and then the set-up menu is appears first. If an error is encountered, for example if the input voltage is outside the allowed range of 10-15 V, a message will be displayed and the buzzer will sound. Disconnect the power supply and rectify the fault.

Important notes

Never connect both power inputs simultaneously as this will destroy the charger!
Make sure to use the correct charging programme (Lithium, NiMh, Lead etc.) for the respective battery! Attempting to charge a battery with a non-compatible charging programme can cause serious damage to the battery and charger. There is a risk of fire or explosion! If you are not sure which charging programme to use for your battery, please contact the manufacturer of the battery or contact our customer service.
The charger is capable of unbalanced charging of multi-cell lithium batteries under controlled conditions when the appropriate charging programme is selected. Unbalanced charging of multi-cell lithium batteries is at your own risk. We strongly advise against this and recommend that multi-cell lithium batteries are always charged balanced. Unbalanced charging can lead to cell voltage drift which can cause the battery to age more quickly and in the worst case can severely damage the battery. There is a risk of fire or explosion!

Battery packs to be charged or discharged are attached to the charger via 2 colour coded banana sockets using a good quality charging cable. Make sure that the plus (+) pole of the battery is con-nected to the red socket on the charger and that the minus (-) pole of the battery is connected to the black socket of the charger.
When charging or discharging Lithium packs, always use the balancer function of the charger. This will not only provide protection for your cells, but also ensure maximum efficiency and long life. To do so, you must connect both the charging cable and the balancer plug/socket (balancerboard included). Not doing this will result in the individual cells not being protected and you will not be able to monitor the individual cell voltage in the display.

Main Screen

After power on the charger, you can see the main menu, press the symbols to select a menu.
Arrow buttons to change the stored charging programs
Enter the memory into the charging/balancing charging/discharging/cycle.
Enter into the balancing charging mode.
Enter into the charging mode.
Enter into the discharging mode.
Enter into the cycle mode.
Enter into the setup mode.
Enter into the batteries doctor mode.
Enter into the extern function mode.
Enter into digital power mode.
*LS > Last working mode.

Initial parameter setup

Pressing the „SET“ button to enter the setup menu

Tips
Please set up correctly in the „user set“ menu before into the job for the first time you use it.

Back Light
20 % ~ 80 %
LCD Contrastx
30 ~ 60
Button Sound
on/off
4 Buzzer Sound
on/off
Max. Out Watt
50 – 80 W
Save / Back
INC / Down
DEC / Up
Input cut
10,0 V ~ 18,0 V
Safety timer
10 ~ 600 min.
Int. Cut-Off
50 ~ 80°C
Temp. Cut-Off
50 ~ 80°C
Max. Out CAPA
500 mAh ~ 50 Ah
Nixx Cycle Mode
C->D/D->C
Nixx Cydle Cnt.
1 ~ 5 T
Cycle Waste time
5 ~ 60 min.
NiMh Delta-Peak
5 ~ 25 mV
NiCd Delta-Peak
5 ~ 20 mV
LiPo CHG Cut
4.00 ~ 4.25 V
LiPo DCHG Cut
3.00 ~ 4.00 V
LiFe CHG Cut
3.50 ~ 3.70 V
LiFe DCHG Cut
1.80 ~ 3.30 V
PB CHG Cut
2.00 ~ 2.50 V
PB DCHG Cut
1.20 ~ 2.00 V
NiMh DCHG Cut
0.80 ~ 1.50 V
NiCd DCHG Cut
0.50 ~ 1.50 V
Lilo CHG Cut
4.00 ~ 4.15 V
Lilo DCHG Cut
3.00 ~ 3.90 V

Getting started to balancing charging/charging/discharging and cycles

Battery type
Set the battery type.
You have to check the battery carefully and set it up correctly, or it will cause a explode.
The selection can be set using the arrow keys (up / down).
Number of cells.
Set the numbers of cells.
The selection can be set using the arrow keys (up / down)
Charge/Discharge current
The selection can be set using the arrow keys (up / down) Press „Save“ to the set presented to store parameters. To start the charging process press „Start“
Save = Enter Memory location
(Place 1 – 10 are pre-programmed)
Input Voltage / Battery check. Start = Start Operation
The charging process is started.

Getting started to balancing charging/charging/ discharging and cycle

Charging/Discharging data In the digital bower menu, charger will shows the parameters which user setted in the last time
Charging/Discharging set dataShould any changes be necessary, select the required data.
Press „Graph“ key to view the current curve.
Press „Cell“ key to view the Cells
NiMH / NiCD Cycle

Battery‘s Doctor Progam

Lipo
can select LiPo/LiFe/Lilo
VOL
can select Voltage/Internal resistance Can select Voltage/Volt
BALA
Start the balancer operation
Balancer control operation, with „Stop“ you can stop the Valancer operation prematurely.

Extern function program

Can select USB Monitor / Servotester
USB Monitor
Servo Tester

Digital power program
In this mode, charger can provide a output power of DC 3,0 V – 24 V for the other electronic equipment.

Set voltage / current / watt / run time
Digital power working.

Warning and error information

The charger is protected agains faults and operator errors by the Multi- Protections-System. Faults/Errors are displayed on the LCD screen and they interrup the active process to protect the unit and the battery.

The output ist connected to a battery with incorrect polarity.
Not connected or connection interruption.
Output short circuits.
Input voltage error, below or over the limit of 10 – 18 V.
Charger fault.
Total voltage too low.
Total voltage too high.
Unit cell voltage too low.
Unit cell votage too high
Balance port connection error.
Charge overheating
Power exceed the limit in the digital power mode.
Current exceed the limit in the digital power mode.
Exceed the maximum safe time limit.
Exceed the maximum capacity limit.
External temperature too high.

Additional information

Your charger is equipped with a powerful internal 80 watt power supply and a socket to connect to an external power supply . When operating on a normal 230V AC power outlet you should making sure the charger ist set to operate within the maximum power of 80 watts . You should set the max. Amp current according to the respective battery , into the range of the allowed maximum Charging rate of the battery and the maximum output of the internal power supply! If you choose charging currents exceeding the 80 watts of the power supply the safety shutdown of the power supply will restart the charger. When connecting to an external power supply to the appropriate power the charger allows higher Loading rates within the technical performance. In the table you can see the charging currents of various lithium batteries. The basis for calculation of Watts is Volts multiplied by amps.

Table of current in Watt/Ampere LiIon

V-máx Cella singola V-max p.cell| Cellule cells| V-máx Pacco batteria V-max battery| Ampere Corrente di carica max. Amp current| Watt Watt
---|---|---|---|---
4,1| 1| 4,1| 10| 41
4,1| 2| 8,2| 10| 82
4,1| 3| 12,3| 7,2| 88,56
4,1| 4| 16,4| 5,4| 88,56
4,1| 5| 20,5| 4,3| 88,15
4,1| 6| 24,6| 3,6| 88,56

Safety Information

Whenever you operate your charger the following safety instructions must be followed.
This device is not intended for use by individuals (including children) with reduced physical sensory, mental abilities, lack of experience and / or knowledge, unless they are supervised in how the device is to be used.
Children should be supervised to ensure that they do not play with the appliance.
Only for indoor use.
The charger may get hot in use, position the unit so that the heat can dissipate.
Never expose the charger to moisture or direct sun light.
After use always disconnect the unit from the mains and unplug any batteries.
Never leave the charger unattended when in use, and always operate it on a fire proof surface.
Avoid short circuits at all costs. Always observe the correct polarity.
Batteries should always be allowed to cool down before you charge or discharge them.
Only charge or discharge packs containing cells from the same manufacturer and of the same capacity.
Do not connect packs in parallel to charge or discharge them.
Always disconnect the pack from any electronic system (ESC etc.) before attempting to charge it.
Connect the charging cable to the charger first and then to the battery.
Never try to charge/discharge damaged packs or cells.
Follow the directions given by the battery manufacturer.
The charger may only be used to charge/discharge the types of cells listed in the technical specifications.
Do not open the unit. This will void the guarantee and may be dangerous. If the charger is damaged or faulty, return it our service department for repair.

Disposal restrictions
Electrical appliances must not be disposed of in domestic waste and must be disposed of separately. You are obliged to take out the batteries, if possible, and to dispose of the electrical equipment at the communal collection points. Should personal data be stored on the electrical appliance you must remove them by yourself.

info@jamara.com ● www.jamara.com
Service – Tel. +49 (0) 75 65/94 12-777 service@jamara.com