vactron CVX925 Central Vacuum Systems User Guide

vactron CVX925 Central Vacuum Systems

INTRODUCTION

First of all, we would like to thank you for choosing the CVX925 central vacuum system. The purpose of the User guide manual for your Vactron central vacuum unit is to show you, the user, the correct operation and maintenance of your system so as to obtain the optimum performance from them. This manual should be considered an inseparable part of your central vacuum unit. Please read the manual carefully before using your central vacuum unit.

SAFETY WARNING

READ THIS MANUAL CAREFULLY BEFORE USE, AND KEEP IT IN A SAFE PLACE. CAUTION:
WARNING: To avoid and reduce risks

1. Check that the voltage on the label of your machine corresponds to that of your electrical supply.

2. This appliance is intended for interior use. Never use this appliance outdoors unless an appropriate Weather Canopy is fitted.

3. Children may mistake this appliance for a toy. Never allow children to use this appliance.

4. Never vacuum directly into the vacuum inlet a burning object or an object that is smoking, such as cigarettes, matches, or hot embers. Pay special attention to embers in the fireplace, even when they seem to be extinguished, since the speed of the air inside the pipes may ignite even the smallest spark.

5. Never vacuum liquids of any kind into your vacuum inlet.

6. Never use the appliance in the presence of a strong detergent, perfume, solvents, or other caustic gases or liquids that may cause a fire.

7. Never vacuum objects that may damage the hose or dust container bags such as small toys, needles, etc.

8. Never vacuum sharp objects such as hairpins, toothpicks, etc.

9. Never vacuum leftovers after cooking, such as vegetable leaves and fish bones, or any other waste such as paper, cloths, sanitary towels, or metallic objects.

10. Never rest heavy or sharp objects on the flexible hose.

11. Never use your ducted vacuum unit without the filter cartridges or any filtering element.

12. Turn off and disconnect the appliance immediately in the event that you notice any unusual noise, the smell of burning, smoke, or any other unusual occurrence during use.

13. Do not try to repair the appliance or arrange for a company to do so that is not authorized by Electron Vacuum Systems Aust Pty Ltd to carry out the repair. Any manipulation of the equipment by personnel not authorized will invalidate the product’s warranty.

14. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

15. In the event of the power cable being damaged it should be replaced by the manufacturer, by
    the after-sale service department, or a similarly qualified individual, so as to avoid any possible danger.

16. In the event that your installation does not work correctly, contact an authorized technical service provider closest to you or the manufacturer.

COMPONENT PARTS

1. Breaker switch

2. Socket for power cable

3. Socket for low-voltage cable

4. ON/OFF switch

5. LED panel

6. Dust container

7. Exhaust

8. Motor housing

9. Carbon filter (motor brushes)

10. Wall hanger

11. a. Air inlet: Hepa+ Pro-Tecta Filter
    b. Air inlet: Dust Bag/Self-cleaning Filter

12. Cyclonic cone housing

13. Dust container handle

14. Pro-Tecta filter

15. Hepa filter

16. Filter cartridge cap

17. Cyclonic Cone

18. Exhaust filter

19. Air Inlet caps

20. Electrical power cord

For use solely in the event that exhausting the unit to the outside is not possible. For insertion in unused air inlets

FIXING THE CENTRAL VACUUM UNIT TO THE WALL

All Vactron central vacuums come supplied with a wall bracket comprising two interlocking pieces, one attached to the rear of the machine, the other to be attached to the wall onto which is slotted the other part of the bracket. The central unit should be fixed permanently to the wall by means of this bracket .

The central vacuum unit should be installed in a well-aired location providing easy access, far away from any heat source. Similarly, it should be located close to an electrical supply point. It should be placed at a height of approximately 0.6m from the floor which will allow for the emptying of the bin. It is advisable to leave a space on either side of the unit to permit easy handling of the unit.
Wherever possible the central vacuum should always be located on a supporting wall or a concrete wall to avoid vibrations. Once the location has been chosen, fix the bracket to the wall and hang the central vacuum unit onto the bracket.

BACK VIEW OF CVX950

DUCTING PIPE TO BE CONNECTED TO EITHER LEFT OR RIGHT ENTRY POINTS- USE EITHER OF THESE TWO ENTRY POINTS LOCATED AS PER PIC . BLOCK OFF ENTRY NOT USED WITH AIR INLET CAP.

DUCTING PIPE TO BE CONNECTED TO EITHER LEFT OR RIGHT ENTRY POINTS – USE EITHER OF THESE TWO ENTRY POINTS LOCATED AS PER PIC. BLOCK OFF ENTRY NOT USED WITH AIR INLET CAP.

USER GUIDE

HEPA+ PRO-TECTA FILTER
The high degree of filtration (Hepa + Pro-Tecta + Cyclonic Cone).

1. Highly-efficient filtration system: 99,97% efficiency in capturing particles to a size of 3 microns.
2. Extended periods without the need for maintenance due to the Pro-Tecta filter.
3. Simple maintenance assisted by the ease of removal and re-installation of the Pro-Tecta and Hepa filters.

CVX925 GENERAL INSTRUCTIONS

1. 1. Connect the power cable. The Orange LED will be permanently lit indicating that it is connected to the power supply. The central vacuum unit is now ready for use.
2. Connect the low voltage wires from the installation to the Terminal Block on side of the power unit.
3. When hose is plugged into inlet point inside house, it will automatically turn on the power unit. The Green LED will be lit.

CLEANING AND MAINTENANCE

The effectiveness of the central vacuum unit and its optimum performance is dependent on its correct use and maintenance. It is recommended that cleaning and maintenance is undertaken on a regular basis to prevent mechanical breakdowns. The central vacuum unit must be disconnected from the electrical supply.

EMPTYING THE DUST CONTAINER

1. Detach the container by unfastening the clamps.
2. Remove the Cyclonic Filter.
3. Empty the dust container.
4. Ensure the Cyclonic Filter is repositioned correctly

CLEANING AND MAINTENANCE OF THE FILTER HEPA+ PRO-TECTA

1. Detach the container from the central vacuum unit.
2. Access the protective filter located inside and remove it by turning it 90 ° anti-clockwise.
3. Remove both the cartridges together.
4. This protective filter is re-usable and can be washed using neutral soap and water. Wait until it is completely dry before refitting it.
5. To access the Hepa filter follow the same procedure as for the protective filter and wash in the same way. Don’t forget to wait until the filter is dry before refitting it.
6. Check that both filters are in perfect condition. Never refit damp or damaged filters. Also, please note that using the central vacuum unit without filters would damage it. Re-position the Hepa filter inside the Pro-Tecta filter and fit both filters together by turning the handle clockwise to lock the filters in place
7. Re-fit the central vacuum dust container.

Manufacturer’s Standard Warranty

Electron Vacuum Systems (Aust.) Pty. Ltd. hereby warrants, subject to the conditions specified herein, to repair or at their option replace;

1. Any part of the Power Unit supplied herewith which, proves to be defective by reason of faulty workmanship or materials without charge for labor or parts for a period of 12 months for domestic/household use from the date of Original Retail Purchase.
2. Any part of the cleaning tools, wands, and hose supplied in the kit which proves to be defective by reason of faulty workmanship or materials without charge for labor or parts for a period of 12 months from the date of Original Retail Purchase. ‘Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.’

(This warranty applies in Australia only. For units sold outside Australia, please refer to the authorized Dealer/Agent in your country for warranty details)

Warranty Conditions

1. This warranty only applies provided that the Ducted Vacuum System:
   • has been operated in accordance with the instructions contained on the power unit and in the owner’s manual furnished with the vacuum system,
   • has not been subjected to misuse, abuse, negligence, or accident,
   • has not been repaired, modified or tampered with by anyone other than an Authorised Dealer/ Agent.
2. This warranty does not cover:
   • power units with defaced serial/identification numbers,
   • ingress of water or other liquid substance into motor blower assembly,
   • incorrect maintenance of vacuum system,
   • motor turbine assembly burn up, due to obstructed ventilation holes, lightning strike, application of over voltage, ingress of sand, mortar, or other materials into ventilation holes,
   • fair wear and tear & consumables e.g. filter, motor brushes, motor bearings, cleaning tools, etc.
   • use of the vacuum system without the filter installed,
   • traveling costs to and from the location of the vacuum machine,
   • damage on other parts of the installation such as pipes, inlets, and removal or reinstallation costs.
3. Where an authorized Dealer/Agent or other installers, installs the system, please refer to your installation contract for warranty procedures and terms. For systems supplied as a Do-it-yourself-kit, the warranty is a Manufacturer’s Warranty only and covers the cost of repair in the factory only, (It does not cover freight in returning any part to and from the factory)

How to obtain Service Under Warranty
The complete Vacuum Power Unit must be presented for Service, together with proof of ownership such as a purchase invoice or installation contract to your Dealer/Agent where the vacuum system was purchased. If the vacuum unit is returned to your Dealer/Agent (for repairs to be carried out under warranty) in an unclean condition, a charge may be made for cleaning. Electron Vacuum Systems (Aust) Ply. Ltd. is not responsible for the installation of the Ducted Vacuum system, faulty workmanship, or the incorrect installation by others, Any queries should be directed to the installer or installing company

For all your Sales and Service requirements

Please contact your Dealer/Agent from where the Ducted Vacuum System was purchased.

Head Office

Scoresby Vlclorla Australia 3179
Tel: 03 9764 8633 CVX925

• Vacuum Motor Spec1f1cat1ons
  Peripheral By-pass discharge YES

• Turbine Stages 2
  Double ball bearings YES
  Diameter of Motor mm 145

• Air Watts 660
  A1rtlow Vs (max) 57
  Sealed Vacuum mm H20 3350

• RPM (max) 30200
  Label Rated Electrical Watts 1800

• Control Circuit 12 V DC YES
  Control Current 100mA YES
  Nominal Voltage 240 V AC YES

Power Unit Physical Specification

Overall Height (mm) 1000

• Overall Diameter (mm) 410
  Hybrid Triflow Filtration Compatible System YES

• Cyclonic Filtration with Hepa Filter YES
  Silencer for Exhaust YES

• Left & Right dueling entry points YES
  Dirt Canister port view YES

• Dirt Canister Capacity hires 25
  Wall Mounting of Power Uni! YES

• Authority Approvals
  “C” Tick Compliance EMC-AS/NZS 1044 YES

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>