TIC AMP 210 Audio Wi-Fi Airplay 2 Installation Guide

TIC AMP 210 Audio Wi-Fi Airplay 2

Introduction

• In the below sections, when instructed to press a specific button on the TIC device, you can either aim the remote control at the speaker/amplifiers and press the button or press the respective button on the speaker/device itself if the specific button is available.
• Not every button mentioned is available on each individual speaker/device
• Please note the position of the IR receiving node on the speaker/device when aiming the remote control. The performance of the remote control may degrade if the remote control is not aiming directly at the node or if strong sunlight is interfering with the signal.
• The range of the remote control is a max of 10 meters. If the signal is not received please move closer.
• A single remote control can control any compatible TIC speaker/device. Aim the remote control carefully if multiple speakers are placed in close proximity.
• Volume control can be individually customized for each speaker via the remote control, via the music/video application (e.g. Spotify, Tune-in, etc.), or on the device itself (if the volume button is available).

Wi-fi setup

1. step1: In the Appstore, find the latest iOS or Android app: “WiiM Pod” and download the app.

2. step2: Power on the TIC Wi-fi Airplay2 device. Hold the Wi-Fi button on your device or remote until the Wi-Fi indicator on TIC Wi-fi Airplay 2 device starts blinking.

3. step3: Open the “WiiM Pod” app.

   • Click ‘Add Device’ if you don’t have any Wi-fi Airplay2 device setup in your environment.
   • Click ‘+’ if you already have one or more TIC Wi-fi Airplay2 devices connected to your network.

4. step4:

5. Click ‘Next’ if the indicator of wi-fi in the device is blinking. Otherwise, hold the wi-fi button until the indicator is blinking and then click ‘Next’.

6. Searching for the target device

7. Choose the target device and click ‘Setup this Device’.
   Note: Each device has a different codename.

8. Choose your wi-fi network and enter the passcode of the network. Then Click
   ‘Next’
   Note: Wi-fi name will be different in your environment

9. Connecting the device to your network

10. Connected to your network

11. Choose a device name from the list or enter a device name yourself

12. step5: Group or ungroup TIC airplay devices.

13. Click the button on any device you wish to group

14. Select all the devices you wish to group together and Click ‘Done’

15. Finish grouping

Note: for ungrouping, unselect the devices you want to remove from the group.

Bluetooth input setup

You can optionally use Bluetooth as an input. To set up a Bluetooth device, simply press the BT button on the remote to switch to Bluetooth mode. If no device has been connected, the BT LED indicator will flash green and you can then select “the code” (Each device has a specific code) from your device’s Bluetooth menu. Once connected, the LED indicator will become solid green. You can also choose BT mode from your music/video application.

Note:
The speaker can remember multiple Bluetooth devices. Speaker will automatically reconnect to the most nearby paired device within range each time you turn it on. The Bluetooth connection range is up to 80 meters (outdoor with a clear line of sight) for Bluetooth 5.0 devices.

Wired inputs

• In addition to wireless Wi-fi or Bluetooth inputs, the TIC AMP series and WBR12 have 4 extra wired input options (HDMI, RCA, Optical, and USB) to easily broadcast non-wireless devices such as TV, radio, home-theater receiver, USB drive, etc. You can use the remote control or the WiiM Pod app to select one of these wired input modes.
• Important: for USB there is no specific button available, to select USB please press the HDMI button for 2 seconds

Equalizer/tone control

With the EQ button on the remote control, you can switch between the equalizer tone presets, like Rock/Pop/Classic/Flat/Jazz/etc. You can select your preferred mode while you listen. As there is no display available to check the selected mode, so please trust your ears.

• Short Press: Changes EQ.
• Long Press: Goes back to default EQ.
• EQ：Flat(default)–>Classic–>Pop–>Rock–>Jazz–>Vocal Booster–>Bass Booster–>Bass Reducer–>Treble Booster–>Treble Reducer–>Flat.
• Models such as AMP150, AMP200, and WB3 also have a bass and treble option to adjust the tone-setting more in detail. To access the bass/treble control please push the “volume” button on the device, the volume led will switch to “bass”. You can adjust the bass with the volume control button. Press it again to switch the led to “treble”, and adjust it with the volume button. When pressed again the LED will switch to volume again, etc.

Streaming music/multi-room setup

iPhones or Other iOS Devices (compatible with AirPlay 2)

• step1: Use the remote control to choose the wi-fi input for all compatible TIC devices. If you could not connect it to wi-fi, just use the remote control to press WIFI for 3-5 seconds, you can hear “wi-fi setup mode”, you will connect your device to wi-fi easily.
• step2: Add your TIC device(s) in the “WiiM Pod” app if it’s not connected to your wi-fi network already.
• step3: Open any music/audio streaming app on your iOS device and pick a song, album, or playlist to play.
• From the Now Playing screen (or iOS Control Center), tap on the AirPlay audio icon.
• In the shown AirPlay window, choose the desired devices to play in a mesh network.

Android Phones/Devices (alternative method for iOS devices)

• step1: Use the remote control to choose the wi-fi input for all compatible TIC devices.
• step2: Add your TIC device(s) in the “WiiM Pod” app if it’s not connected to a wi-fi network already.
• step 3: From the Device List screen in the “WiiM Pod” app, drag desired devices onto the “main” device to create a mesh network group.
• step4: Use the remote control to change the input of the “main” device to Bluetooth. Connect your Android device to the “main” device via Bluetooth. When streaming from any music/audio app, all devices in the mesh network group will play together.

Important notes

• For more AirPlay 2 help, please visit: https://support.apple.com/en-us/HT202809#ios
• You may choose another input (HDMI/AUX/Optical/USB) in the “main” device and all the connected devices in the network group will play this selected input.
• For iOS devices (with compatible iOS versions), we strongly recommend using AirPlay 2 directly instead of using the music/video app for the optimal multi-room experience.
• You will only need to use the app to set up the TIC wi-fi devices initially. After devices are connected to your network, the app is no longer needed for standard control and streaming. But please keep the app to update firmware, rename devices, troubleshoot, etc.
• Please make sure to have a strong Wi-fi network (minimum 80% strength). If not, you may encounter issues with playing multi-room Airplay, etc.

References

• Use AirPlay to stream audio - Apple Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>