Shelly Plus 1PM Wi-Fi Smart Switch User Guide

: June 5, 2024
: Shelly

Table of Contents

Shelly Plus 1PM Wi-Fi Smart Switch
Introduction to Shelly
Legend
Installation Instructions
Initial inclusion
Specification
Declaration of conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Shelly Plus 1PM Wi-Fi Smart Switch

CAUTION!
Before beginning the installation, please read this guide and any other documents accompanying the device carefully and completely. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of the law or refusal of legal and/or commercial guarantee (if any). Allterco Robotics EOOD is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure of following the user and safety instructions in this guide.

Introduction to Shelly

Shelly® is a line of innovative microprocessor-managed devices, which allow remote control of electric appliances through a mobile phone, tablet, PC, or home automation system. Shelly® devices can work standalone in a local Wi-Fi network or they can also be operated through cloud home automation services. Shelly® devices can be accessed, controlled and monitored remotely from any place the User has Internet connectivity, as long as the devices are connected to a Wi-Fi router and the Internet. Shelly® devices have integrated web servers, through which the user may adjust, control and monitor them. The cloud function could be used, if it is activated through the web server of the device or the settings in the Shelly Cloud mobile application. The user can register and access Shelly Cloud using either Android or iOS mobile application, or with any internet browser at https://my.shelly.cloud/
Shelly® Devices have two Wi-Fi modes – Access Point (AP) and Client mode (CM). To operate in Client Mode, a Wi-Fi router must be located within the range of the device. Devices can communicate directly with other Wi-Fi devices through HTTP protocol. An API is provided by Allterco Robotics EOOD. For more information, please visit: https://shelly-api-docs.shelly.cloud/#shelly- family-overview. or contact us at: developers@shelly.cloud Shelly® Plus series offers PM-products for real-time precise power measurement. Control your home with your voice Shelly® devices are compatible with Amazon Alexa and Google Home supported functionalities. Please see our step-by-step guide on: https://shelly.cloud/support/compatibility/

Connecting to the power grid with power supply 110-240 V AC (fig. 1), or 24-30 V DC* (fig.2).

Legend

N: Neutral terminal/wire
L: Live (110-240V) terminal/wire
O: Output terminal
SW: Switch terminal
+ : DC positive terminal
: DC ground terminal
GND: DC ground wire
DC+: DC positive (24-30 V) wire

Installation Instructions

The Wi-Fi Relay Switch Shelly® Plus 1PM (the Device) can control 1 electrical circuit up to 3.5 kW. It can be retrofitted into a standard in-wall console, behind power sockets and light switches or other places with limited space.

CAUTION! Danger of electrocution. The mounting/installation of the Device should be done by a qualified person (electrician).
CAUTION! Do not connect the Device to appliances exceeding the given max load!
CAUTION! Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.
CAUTION! Тhe Device may be connected to and may control electric circuits and appliances only if they comply with the respective standards and safety norms. Short circuit in the power grid or any appliance connected to the Device may damage the Device.

RECOMMENDATION!
Connect the Device using solid single-core cables with increased insulation heat resistance not less than PVC T105°C.

Before starting, wire check that the breakers are turned off and there is no voltage on their terminals. This can be done with a phase meter or multimeter. When you are sure that there is no voltage, you can start wiring the cables according to fig.1, if you are using AC power supply. Connect the load to the “O” terminal of the Device and the Neutral wire. Connect the Live wire to an “L” terminal of the Device. Connect the Neutral wire to an “N” terminal of the device. Connect the switch to the “SW” and any of the unused “L” terminals of the Device. If you are using DC power supply, connect the wires according to fig 2. Connect the load to the “O” terminal of the Device and the DC+ wire. Connect the GND wire to a “ +” terminal of the Device. Connect the DC+ wire to a “+ ” terminal of the device. Connect the switch to the “SW” and any of the unused “+ ” terminals of the Device.

CAUTION!
Use only one phase AC circuit. Do not use mixed AC and DC circuits.

RECOMMENDATION
For inductive loads, which cause volt-age spikes during switching, such as electrical motors, fans, vacuum cleaners, refrigerators and similar ones, RC snubber (0.1µF / 100Ω / 1/2W / 600V AC) should be wired in parallel with the load. RC snubbers can purchased at https://shop.shelly.cloud/rc-snubber-wifi- smart-home-automation.

Initial inclusion

You can choose to use Shelly® with the Shelly Cloud mobile application and Shelly Cloud service. Instructions on how to connect your device to the Cloud and control it through the Shelly App can be found in the “App guide”. You can also familiarize yourself with the instructions for Management and Control through the embedded Web interface at 192.168.33.1 in the Wi-Fi network, created by the Device.

CAUTION!
Do not allow children to play with the button/switch connected to the Device. Keep the Devices for remote control of Shelly (mobile phones, tablets, PCs) away from children.

Specification

AC power supply: 110-240 V
DC power supply: 24-30 V
Power metering: YES
Max load: 16A/240V
Dimensions (HxWxD): 42x38x17 mm
Scripting (mjs): YES
MQTT: YES
Temperature Protection: YES
URL Actions: 20
Scheduling: 50
Wi-Fi: YES
Bluetooth: v4.2
Basic/EDR: YES
Bluetooth modulation: GFSK, π/4-DQPSK, 8-DPSK
Controlled elements: 1 electrical circuits (max 30 V in DC mode).
Controlling elements: 1 relay
Working temperature: -20°C up to 40°C
Electrical consumption: < 1.2 W
CPU: ESP32
Flash: 4MB
Operational range: (depending on terrain and building structure): up to 50 m outdoors, up to 30 m indoors
Radio signal power: 1mW
Radio protocol: WiFi 802.11 b/g/n
RF output Wi-Fi: 13.38 dBm
RF output Bluetooth: 4.93 dBm
Frequency Wi-Fi : 2412-2472 МHz; (Max. 2495 MHz)
Frequency Bluetooth: TX/RX: 2402- 2480 MHz (Max.2483.5MHz)

Declaration of conformity

Hereby, Allterco Robotics EOOD declares that the radio equipment type Shelly Plus 1PM is in compliance with Directive 2014/53/ EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address https://shelly.cloud/knowledge-base/devices /shelly-plus-1pm/
Manufacturer: Allterco Robotics EOOD
Address: Bulgaria, Sofia, 1407, 103 Cherni brah Blvd.
Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
Web: https://www.shelly.cloud
Changes in the contact data are published by the Manufacturer at the official website of the Device https://www.shelly.cloud All rights to trademark Shelly® and other intellectual rights associated with this Device belong to Allterco Robotics EOOD.