EAGLE G600AF 45M-90M LED Rope Light Instruction Manual
- June 3, 2024
- EAGLE
Table of Contents
G600AF 45M-90M LED Rope Light
Instruction Manual
G600AF 45M-90M LED Rope Light
IMPORTANT
Installers Please Note:
This information should be read carefully before installation.
CONTENTS
45m Kit | 90m Kit |
---|---|
1 x 45m Roll of LED Rope Light | 1 x 90m Roll of LED Rope Light |
5 x End Caps | 10 x End Caps |
5 x Inline Couplers | 10 x Inline Couplers |
5 x Mains Leads | 10 x Mains Leads |
5 x Mains Connector | 10 x Mains Connector |
5 x Strips of Heat shrink and glue | 10 x Strips of Heat shrink and glue |
Important Information
This item and its components are designed for use by a professional/competent
person to produce a bespoke design/effect. It is not a finished product, and
as such, it is the responsibility of the installer to make sure that the
finished product/installation is suitable for the purposes it is being used
for and is installed to meet all current legislation and standards. The
installer should pass onto the user a comprehensive working document on how to
safely use and maintain the product in the form of a professional written
manual. A qualified electrician should test the finished item before
commissioning and handing it over to the user.
Operation and Installation Guide
-
The rope light can be cut every 1m at the point marked on the rope light by a pair of scissors or a broken line.
-
The cut must be made by a sharp knife and at right angles to the rope. Incorrect cutting of the product can cause the final join to suffer from the poor electrical connection which can lead to product failure.
-
The product can be reconnected in various ways by using the connectors provided.
1. In-Line Coupler 2. Mains Connector 3. End Cap -
All connections MUST be sealed with the heat shrink provided to make a permanent join. Failure to use the heat shrink may result in the ingress of water and/or the breaking of the electrical connection leading to the possibility of electrical shock/product damage.
-
The rope is suitable for use outside but if any connections are to be mounted outside or are to be exposed to any form of weathering then these connections must be additionally weatherproofed. The accessories supplied do NOT offer any form of IP-rated protection.
-
The rope light should not be switched on while on the roll, in a tight coil or in very close proximity to other LED ropes. This can lead to overheating and damage to the product.
-
The maximum achievable curve is 75mm. A curve of less than 75mm may stress the PVC sheath lead to product damage and Electrical failure.
-
The product should NOT be mounted using staples, nails or metal fixings which can cause damage to the plastic sheath. Cable ties can be used but must not be over-tightened.
-
Only the connectors supplied are suitable for this product. Further accessories are available on request. The use of alternative connectors may lead to poor electrical contact and product damage/failure. A list of these appears at the foot of this document.
-
The maximum single length that can be run from one power supply is 90m.
-
The LED rope is polarity sensitive and will only work one way so if the product does not illuminate switch the contacts the other way by reversing the connection. To do this remove the power lead and rotate 180 Degrees and re-connect.
Maintenance
Periodically check the product for LED failure and general damage. If any of
the LEDs have failed or the product is damaged in any way switch off and
disconnect from the mains supply.
To clean the product, switch off and disconnect from the main supply. Using a
slightly damp cloth gently wipe over. Do not use bleach, solvent-based
cleaners, or strong detergents. These may damage the product and invalidate
the warranty. If the mains lead is damaged, it must be replaced by the
manufacturer or an authorized service center.
If the mains plug needs to be replaced, proceed as follows:
- Connect the brown wire to the terminal labeled “L”.
- Connect the blue wire to the terminal labeled “N”.
- Make sure that the cord grip is positioned correctly (over the outer sheath of the cable) and it fully tightened.
- If the plug is fitted with a 13 A or 5 A fuse, replace it by a 3 A fuse.
DISPOSAL AND RECYCLING
You must not dispose of this item with domestic household waste.
PAT TESTING
When used in an office environment, we recommend that this product should be
safety-tested yearly by a qualified electrician (PAT Tested).
We recommend that it is PAT tested regularly when used in a domestic
environment.
GENERAL SAFETY REQUIREMENTS
Domestic wiring must be tested periodically by a qualified electrician at
least once every 10 years or at every change of occupancy.
For office and retail premises, and buildings such as village halls, the
wiring must be inspected at least once every 5 years.
It is recommended that all buildings be fitted with smoke alarms (it is
mandatory for new buildings).
List of other available accessories (Not Supplied)
G800AM| Inline Coupler|
---|---|---
G800AN| Mains connector|
G800AP| End Cap|
G800AT| Accessory kit|
G800AV| Power Lead|
G803AN| 13mm Clip|
G803AQ| 13mm Channel|
G803AS| 13mm flexible channel|
G803AT| 13mm reflective chann|
TECHNICAL SPECIFICATION
Voltage | 230V ~ 50Hz |
---|---|
Fuse Rating | 3A |
Power Consumption | 1.8W per m |
Tube Diameter | 13 mm |
Number of LED’s Weight | 36 per m |
45m | 10kg |
90m | 20kg |
SERVICE WARRANTY
Eagle guarantees the product free from defects in materials and workmanship
for a period of twelve months. Should this appliance be operated under
conditions other than those recommended, at voltages other than the voltage
indicated on the appliance, or any attempts made to service or modify the
appliance, then the warranty will be rendered void. The product you buy may
sometimes differ slightly from the illustrations. This warranty is in addition
to and does not affect, your statutory rights. Our guarantee is administered
by our retailers. If your product arrives damaged, you must contact the
retailer from whom you bought it. The retailer’s contact details will be on
the invoice that arrived with the product, or on the e-mail, you received when
you placed the order. Do not contact Eagle, only your retailer can arrange a
replacement. If your product fails within the guarantee period, firstly read
the “fault finding” section of this manual, because temperature and weather
conditions can affect the performance of certain products. If the product
needs to be repaired or replaced, you must contact the retailer from whom you
bought it. The retailer’s contact details will be on the invoice that arrived
with the product, or on the e-mail, you received when you placed the order. If
you have just received your product and require technical help in using it,
please call our Help Desk on (0845) 459 4816 If you have any other technical
queries about the product, please call our Help Desk at (0845) 459 4816.
Eagle is a Trademark of Electrovision Ltd.
Lots Lane, Sutton, St. Helens, Merseyside. WA9 3EX
website: www.electrovision.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>