Avallon AIMG151GSSIRH 15-Inch 26 lb. Freestanding Ice Maker User Manual

AIMG151GSSIRH 15-Inch 26 lb.
Freestanding Ice Maker
User Manual

Installation

The ice maker should be installed by a licensed plumber in accordance with local electrical and plumbing code requirements. The ice maker should also be placed in a location that is strong enough to support its total weight. Before you plug the ice maker into a power supply, be sure to let it stand upright for at least 24 hours to allow the compressor’s oils to settle.
Unpacking the Ice Maker

Warning: Use two or more people to move and install the ice maker. Failure to do so can result in back or another injury. Carefully remove the packaging materials. Remove any shipping tape and glue from your ice maker before use. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your ice maker.
**Warning: Do not remove any safety, warning, or product information labels from your ice maker.
Types of Installation
This ice maker has been designed for freestanding or built-in installation. In each case, there must be adequate ventilation and access to service. Install the unit in a location where the ambient temperature is above 50°F and below 100°F.
Freestanding Installation:
A free-standing installation will allow you to install the ice maker in almost any place you desire. You must follow the stated instructions for electrical requirements and leveling the ice maker.
Built-in Installation:**
A built-in installation will allow you to install the ice maker under a counter as long as the required clearance space around the ice maker is provided. It is necessary to allow adequate ventilation space around the unit, including at the back of the unit.
The following additional items must be observed:

1. Place the ice maker in front of the installation location. Adjust the feet and level the unit so it sits properly on the floor or on a platform depending on your installation requirements.
2. The water supply line must be plumbed before connecting it to the ice maker. Install the drain line into your drain.
3. Turn on the main water supply and tap. Check for water leaks at all connections.
4. If the electrical outlet for the ice maker is behind the cabinet, plug in the ice maker.
5. Push the ice maker into position.
     Warning: DO NOT install the ice maker behind a closed cabinet door.

Clearance Requirements
  Notes:

• To ensure proper service access and ventilation, at least 2 inches of clearance at the back as shown in the diagram.
• The installation should allow the unit to be pulled forward for servicing, if necessary.
• A standard electrical supply (115 VAC only, 60 Hz), properly grounded in accordance with National Electrical Code and local codes and ordinances, is required.

When installing the ice maker under a counter, follow the recommended spacing dimensions shown.
To ensure proper service access and ventilation, allow at least 2″ of clearance at the back, ¼” at the top, and ¼” at the sides. The installation should allow the unit to be pulled forward for servicing, if necessary.

| |
---|---|---
Side View| Top View| Door Swing

  Note: The ice maker should be installed on a firm and level surface that will be able to support the entire weight of the unit. It is important for the ice maker to be level in order to work properly. If needed, you can adjust the height of the ice maker by rotating the feet. See the “Leveling the Ice Maker” section.
Note: A standard electrical supply (115 VAC only, 60 Hz), properly grounded in accordance with National Electrical Code and local codes and ordinances, is required.

Electrical Requirements

ELECTRIC SHOCK HAZARD!

• Plug into a grounded 3-prong outlet.
• Never remove the grounding prong from the plug.
• Never use an adapter to bypass the grounding prong.
• DO NOT use an extension cord.
• Failure to follow these instructions can result in fire, electrical shock, or death.

Before you move your ice maker into its final location, it is important to make sure you have the proper electrical connection:

• A standard electrical supply (115 V, 60Hz), properly grounded in accordance with the National Electrical Code and local codes and ordinances, is required.
• It is recommended that a separate circuit, serving only your ice maker, be provided. Use receptacles that cannot be turned off by a switch or pull chain.
• The fuse (or circuit breaker) size should be 15 Amps.

Recommended Grounding Method
For your personal safety, this appliance must be grounded. It is equipped with a power supply cord that has a 3-pronged grounding plug. To minimize possible shock hazards, the cord must be plugged into a mating 3-pronged wall socket, and grounded in accordance with the National Electrical Code and local codes and ordinances. If a mating wall socket is not available, it is the personal responsibility of the customer to have a properly grounded, 3-prong wall receptacle installed by a qualified electrician.

Leveling the Ice Maker

The ice maker should be installed on a firm and level surface that will be able to support the entire weight of a fully-loaded unit. It is important for the ice maker to be leveled in order to work properly. It can be raised or lowered by rotating the feet on the bottom of the machine. If you find that the surface is not level, rotate the feet until the ice maker becomes level. You may need to make several adjustments to level it. We recommend using a carpenter’s level to check the machine. Turn the leveling feet to the right to lower that side of the ice maker. Turn the leveling feet to the left to raise that side of the ice maker.

Important: Once you are ready to install the unit in a cabinet or directly on the floor, you must adjust the feet to level the ice maker.

Installing the Door Handle
To install the door handle:

1. Open the door and carefully pull out the section of the door gasket that covers the hole where the handle is to be installed.
2. Insert each Phillips head screw through the hole on the inside of the door until the screw passes through to the outside of the door.
3. Align the handle with the screws and tighten using a Phillips head screwdriver until the handle is flush against the door frame.
4. Carefully press the door gasket back into its original position.

Caution: Do not over-tighten the screws as this may cause damage to the handle or to the door.
Note: Panel-ready models allow for the installation of different handles, which may be affixed to the panel overlay directly. Door handle installation may be different than the above instructions.

Connecting the Water Supply and Drain Lines
The water supply should be ready at the point of installation. The water supply pressure should be a minimum of 20 psi with a static pressure of no more than 80 psi. A wall outlet directly behind the ice maker will make installation easier. When you connect the water supply line and drain line, ensure they are installed in the correct locations.
Important: All installations must be done in accordance with local plumbing code requirements. Do not pinch, kink, or damage the water supply or drain lines during installation. Check for leaks after connecting lines.
Connecting the Water Supply Line

1. Turn off the main water supply. Turn on the nearest faucet long enough to clear the line of water.
2. A shut-off valve must be installed between the ice maker and the main water supply.
3. Connect the water supply line to the COLD water piping using copper tubing with a ¼” compression fitting to the unit or ¼” reinforced PVC tubing.
4. Install the included water line adapter to the back of the unit. Wrap the threads of the adapter with Teflon tape to ensure a proper seal.
5. Connect the water supply line to the adapter. Tighten the connection to the unit firmly by the hand, then tighten one-half turn with an open-ended wrench.
6. Turn on the main water supply and open the shut-off valve. Check for leaks at all connection points. Repair any leaks.

Note: It is strongly advised to always use a water filter with your ice maker. A water filter can remove taste and odors as well as particles. Where water is very hard, softened water may result in white, mushy cubes that stick together. Deionized water is not recommended.
Connecting the Drain Line
There are two options for drain operation: One that drains by gravity and one that utilizes an internal drain pump. Follow the instructions below for your model’s configuration.
Gravity Draining (AIMG151GPRI, AIMG151GSSI)

1. Locate the floor drain near the ice maker. Your drain line must be long enough to reach the floor drain and must slope downward ¼” for every foot of line. An air gap is required between the drain line and the floor drain. A standard P-trap in the floor drain piping is typically recommended.
2. Install the included drain adapter to the back of the unit. Wrap the threads with Teflon tape to ensure a proper seal.
3. Connect the drain hose to the installed drain adapter, then insert the other end of the drain line into the floor drain.
4. Pour 2-4 quarts of water into the ice bin to check for proper drainage.

Pump Draining (AIMG151PPRI, AIMG151PSSI, AIMG151PSSO)

1. The drain pump can pump water up to 4 feet vertically and 20 feet horizontally. Your drain location must be within these distances. Consult a licensed plumber for proper installation.
2. Install the included drain adapter to the back of the unit. Wrap the threads with Teflon tape to ensure a proper seal.
3. Connect a drain hose to the installed adapter, then securely connect the other end of the drain line to the desired drain location.
4. Connect power and turn on the ice maker.
5. Pour 2-4 quarts of water into the ice bin to check for proper drainage.

Operation

Installation Checklist before Operation

1. Have all packing materials and tape been removed from the interior and exterior of the ice maker?
2. Has the ice storage bin been cleaned?
3. Have the installation instructions been followed, including connecting the unit to water and electricity?
4. Is the unit properly grounded?
5. Does water drain correctly?
6. Have leaks been tested for at all connection points and repaired, if necessary?
7. Has the machine been leveled?
8. Is the ice maker in a site where the ambient temperature is between 50°F and 100°F all year round?
9. Is there a clearance of at least 2″ at the rear, 1/4″ at the top, and 1/4″ at the sides for proper air circulation?
10. Has the water supply pressure been checked to ensure a minimum of 20 psi with a static pressure not to exceed 80 psi?
11. Is the ice maker plugged in?
12. Has the main water supply and shut-off valve been turned on?

Initial Operation

1. Turn on the main water supply and open the shut-off valve to the ice maker and let the water fill the line.
2. Plug the ice maker into the electric outlet.
3. Open the door and turn the power switch to the “ICE” position.
4. Let the unit run and produce 2-3 batches of ice (approximately 1-2 hours). Discard the ice from these initial productions.
5. The ice maker is now ready for use. The unit will automatically continue to produce ice until the bin is full.

Ongoing Operation
The ice maker’s power switch must remain in the “ICE” position for ongoing, daily operation. The ice maker will automatically produce ice until the bin is full. As ice is removed or melts, the unit will continue to produce ice and keep the bin full. The ice maker will produce 1 batch (24 pieces) of ice every 25-30 minutes under normal temperature conditions (50° to 100°F). Under normal conditions, it takes approximately 10-12 hours to completely fill the ice bin.
Remove ice from the bin using the scoop provided. Hang the scoop from its hook after use to prevent it from being buried under the ice. Keep the scoop clean like any kitchen utensil.
Do not put anything other than ice into the ice bin. Cans or bottles are unsanitary and may freeze or leak. Bottle labels may detach and block the drain.
The ice maker must be regularly cleaned in order to operate correctly. Mineral or mold build-up will adversely affect the unit’s operation. Follow the instructions in the “Cleaning and Maintenance” section of this manual to keep your ice maker sanitary and operating properly.
Normal Sounds
Your new ice maker may make noise during normal operation. Most of these sounds are normal. Hard surfaces like the floor and walls can make the sounds seem louder than they actually are.
The following describes several sounds you may hear and what may be making them:

• Rattling noises may come from the flow of the refrigerant or the water line. Items stored on top of the ice maker can also make noises.
• The high-efficiency compressor may make a pulsating or high-pitched sound.
• Water running across the evaporator while making ice may make a splashing sound.
• As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your ice maker.
• You may hear air being forced over the condenser by the condenser fan.
• During the ice harvest cycle, you may hear the sound of the ice cubes falling into the storage bin.

Warning: Never attempt to remove frost with a sharp object!
Preparing the Ice Maker for Storage
If the ice maker will not be used for a long time or is to be moved to another place, it will be necessary to defrost and clean the unit and dry the interior.

1. Disconnect the ice maker from the power supply by removing the power plug from the wall socket.
2. Turn off the water supply at the shut-off valve.
3. Disconnect the water supply line and drain line.
4. Remove all ice from the storage bin and clean the unit thoroughly (see “Cleaning and Maintenance” section).
5. Leave the door open to allow for air circulation and to prevent mold, mildew, and unpleasant smells.
6. Once the interior is dry and cleans the unit will be ready for storage.

Caution: Store the unit out of reach from children. If you have children, you may want to take additional precautions such as removing the door to prevent a child from being trapped inside the ice maker.
Important:
• Do not touch the power plug when your hands are wet.
• Never unplug the unit by pulling on the cord.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>