LMP WMS-1657C Bluetooth Master Mouse User Guide
- June 5, 2024
- LMP
Table of Contents
LMP WMS-1657C Bluetooth Master Mouse User Guide
LMP Master Mouse WMS-1657C (Bluetooth)
Optical 2-button Bluetooth mouse for macOS and iOS devices with scroll wheel &
aluminum housing
Overview
- LED Indicator
- Power Switch
- Pairing button
- USB-C charging port
LED Indication
LED (Green) Power on – LED still on for 2 seconds and turn off (1st time to
power on mouse).
LED (Green) Pairing – LED flashing slowly until pairing with Bluetooth host
has been completed.
LED (Green) Power on – LED flashing 3 times or more until connecting to pre-
set Bluetooth host has been re-established.
LED (Red) Charging – Solid red LED while charging and will go off when battery
is fully charged.
LED (Green) Low Power – LED flashing fast (function only in active mode).
Getting Started
Fully charging the LMP Master Mouse Bluetooth before initial use is highly recommended
- Use the USB-C cable to charge the Master Mouse. You can charge it via your host‘s USB-C or USB-A port (with adapter) or by using a USB power supply with 5V output. When fully charged, the LED will be off.
- Turn on the mouse using the power switch (to «On» position).
- Start the pairing process with any Bluetooth enabled host. Follow the steps below.
- To preserve battery power, it is highly suggested to turn off the Master Mouse when not in use for a longer period of time (e.g. at night or over the weekend)
FCC Statement
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, users and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or
television reception, which can be determined by turning the device off and
on, the user is encouraged to try to correct the interference by one of more
of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate this device. (Example: use only shielded interface cable when connecting to computer or peripheral device).
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 0.5 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this device. Such modifications could void the
user authority to operate the device.
Pairing Process
Ensure that your host has Bluetooth activated.
Note that you need a trackpad or connected mouse to go through the pairing process.
(1) Turn on the Master Mouse using the power switch (to «On» position).
(2) Select the Bluetooth icon in your System Preference.
(3) Ensure that Bluetooth is activated on your host.
(4) Press the Master Mouse’s pairing button with a pen.
(5) In the Bluetooth pane, «LMP WMS-1657C» will be displayed under the list of found Bluetooth devices. Select «LMP WMS-1657C» and click «Connect».
(6) In macOS 10.12 and higher, Windows 7 and higher, iOS etc., the connection between the Master Mouse and your host will be established automatically.
(7) The Master Mouse is now marked as «connected» and ready for use.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>