Time Warner UR3-SR3 Subscription Broadcast Remote Control Instruction Manual

Warner UR3-SR3 Subscription Broadcast Remote Control
Instruction Manual

Operating Manual For Easy Clicker
UR3-SR3
Universal Remote Control, Inc.
www.universalremote.com
OCE-0009D REV 40

Introduction

This remote control is designed to operate most Digital and Analog Cable Boxes, as well as TVs, and a DVD player.

Replacing Batteries

Before you program or operate the remote control, you must install two new AAA alkaline batteries.

STEP1 Remove the battery compartment cover from the back of your remote control.
STEP2 Check battery polarity carefully and install the batteries as shown in the illustration below.
STEP3 Replace the battery compartment cover.

Button Functions

Programming the Remote Control.

*Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either the CBL, TV or DVD button, depending on which device you are programming the remote to operate.

Quick Set-Up Method

STEP1 Turn on the component you want to program. To program your TV, turn on the TV.
STEP2 Press and hold the [DEVICE] key for 5 seconds until the Device LED will blink once and stays on. Continue to hold the [DEVICE] key and press the number key assigned to your brand in the Quick Setup Code Table and release both the [DEVICE] key and the number key to save the code. The Device LED will blink twice to confirm that the code is stored.
STEP3 Point the remote control at the component.
STEP4 Press the [DEVICE] button. If it turns off, it is programmed for your component. If it does not turn off, use the PreProgrammed 3-Digit code Method or Scanning Method.
Repeat the steps above for all components (CBL, TV, DVD).

Quick Set-up Code Tables

CBL

Quick Number

|

Manufacturer/Brand

---|---
0| PACE DATA
1| SA/CISCO, SAMSUNG, PACE DIGITAL
2| MOTOROLA DIGITAL
3| MOTOROLA DATA
4| EVOLUTION DTA
5| CISCO IPTV
6| ADB IPTV
7| TECHNICOLOR
8| AMINO 140/540 IPTV
9| MOTOROLA IPTV

TV

Quick Number|

Manufacturer/Brand

---|---
0| SANYO
1| SONY
2| SAMSUNG
3| LG
4| TOSHIBA
5| PANASONIC
6| PHILIPS
7| HITACHI
8| SHARP
9| VIZIO

DVD

Manual Programming

The remote control can be programmed by entering a three-digit code number that corresponds to particular brands and models of equipment. The three-digit code numbers are listed in the code tables sections of this instruction manual.
STEP1 Turn on the equipment that you want the remote control to operate Cable Box, TV and DVD.
STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment and enter the three- digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off.
*Note : Youcanverifythatyouhaveselectedthe correct code by pressing the [MUTE] button. The equipment should turn on or off.
STEP4* Store the three-digit code by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored.
Note** : Try all the functions on the remote control. If any of the functions do not operate as they should, repeat the instructions from Step 2 using the next three-digit code number from the same brand list.

Auto-Search Method

If none of the three-digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:
STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV, or DVD).
STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on.
STEP3 Press the [CH ] or [CH ] button one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release the [CH ] or [CH ] button as soon as the equipment turns off.
*Note : You can verify that you selected the correct code by pressing the [MUTE] button.TheequipmentshouldturnOnor Off.
STEP4 Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored.

To find the Three-Digit Code that Was Programmed using the Auto Search Method
STEP1 Press the appropriate [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on.
STEP2 Press the [INFO] button. The device LED will blink a number of times indicating the number of each digit for the code. Each digit is separated by a one-second interval of the LED is off. Example: Oneblink,the three blinks,the eight blinksindicatesthecodenumber138. *Note : Tenblinksindicatesthenumber0.

Programming a Second TV to the DVD Button

STEP1 Press the [DVD] button and the [OK/SEL] button simultaneously for 3 seconds. The DVD LED will turn on for 20 seconds. The next step must be performed while the LED is on.
STEP2 Press the [TV] button.
STEP3 Point the remote control toward the TV and enter the three-digit code for your TV from the TV codes table.
STEP4 Store the three-digit code by pressing the [DVD] button. The device LED will blink twice to confirm that the code has been stored.

Programming for Advanced Functions.

In the CABLE device mode, the A, B, C, D, and blank macro buttons can be programmed to act as a ‘Macro’ or Favorite Channel button. This allows you to program up to five 2-digit channels, four 3digit channels, or three 4-digit channels that can be accessed with ONE button press.
*Note: The A,B, C, and D buttons are not programmableifyouhaveaDigital Cable Box made by Pace, Pioneer or Scientific-Atlanta.
STEP1 Press the [CBL] button to select the CBL mode.
STEP2 Press the [MACRO] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds.
STEP3 Enter the 2, 3 or 4-digit code for the channel you want programming first (for example, 007) using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example, 050), then press the [STOP] button. Repeat this process for the third channel. The [CBL] button will blink once for each channel entered.
STEP4 Press the [CH **] button to store the channels that were selected. The [CBL] button will blink twice to confirm the storage of commands.
To access the programmed channels, press the [MACRO] button once. This will bring up the first channel. Press once again and it will bring up the second channel. Press again and it will bring up the third channel.
To erase the Macro programming and return to the original function:
STEP1 Press the [CBL] button to select the CABLE mode.
STEP2 Press a [MACRO] button and the [OK/SEL] button simultaneously for 3 seconds. The CBL device LED will turn on for 20 seconds. The next step must be performed while the LED is on.
STEP3 Press the [CH **] button to erase the functions stored in the button. The CBL device LED will blink twice to confirm that the memory button has been erased.

Assigning the Volume and Mute keys to a Different Device

By default, the VOL , VOL and MUTE keys operate through your TV. If you would like those keys to operate those functions on a different device, follow these steps.
STEP1 Press the [OK/SEL] button and [CBL] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on.
STEP2 Press the [VOL **] button. The device LED will blink.
STEP3 Press the [DEVICE] button corresponding to the device that you would like the volume and mute buttons to control. The device LED will blink twice to confirm the programming.
Example:** If you wish to have the volume and mute keys operate your Cable Box, pressthe[CBL]buttoninStep3.

Assigning the Channel keys to a Different Device

By default, the CH , CH , NUMERIC and LAST keys operate through your Cable Box. If you would like those keys to operate those functions on a different device, follow these steps.
STEP1 Press the [OK/SEL] button and [CBL] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on.
STEP2 Press the [VOL **] button. The device LED will blink.
STEP3** Press the [TV] button. The device LED will blink twice to confirm the programming.
*Note : Ifyouwishtohavethechannelkeys operateyourCableBox,pressthe[CBL] buttoninsteadofthe[TV]buttoninStep3.

Assigning the DVD-VOD keys to control your DVD

By default, the REW, Play, FF, Record, Stop and Pause keys operate VOD (Video On Demand) through your Cable Box. If you would like those keys to operate those functions on your DVD, press the PLAY button for 3 seconds until the DVD button lights. To return to your Cable Box control, press the PLAY key again for 3 seconds until the CBL button lights.

Low Battery Warning

When the battery is low (2.3V-2.0V) and needs to be replaced with fresh batteries, device LED will blink 2 times in sequence whenever a [DEVICE] button is pressed to turn on the equipment.

Memory Lock System.

This remote control is designed to retain programmed memory for 10 years — even after batteries are removed from the remote control. For additional information about your remote control, go to www.universalremote.com

Set-up Code Tables

CABLE TV

CODE No

---|---|---
DREAM| DM7020S| 159
TV| DSTV [PVR1]| 182
DSTV [PVR2]| 183
DUNE| SMART B1,BE,D1,H1,HE,ME| 184
MINI, ULTRA| 185
Duson| totally| 218
ENTONE| URC PLUS| 155
Kamai 651| 221
Kamai 500| 210 221
| 213
Kamai 45x| 221
EVOLUTION FTA| X0-01| 158
EVOLUTION| UNIVERSAL SD DTA| 189
UNIVERSAL HD DTA| 215
Foxtel| IQ3| 228
HAMLIN| CR6000| 042
CR6600,6800,CR83| 043
CRX5000| 044
HOMECAST| NC3000C01| 176
Horizon| Ziggo| 225
Humax| 101-H| 231
Innovative Systems| IPTV Receiver| 262
KAON| Mini| 208
Layer3| C12516| 226
MOXI| MOXI MEDIA CENTER| 006
MOXI HD DVR| 052
2056-MSX| 153
MARIO| Evo Series| 054 055
NAGRA| DCI-4136M| 211
NAGRAVISION| HDD| 201
XBOX| ADB-5720SX| 181
ABD5720SX| 186
NFUSION| NUVENIO SD PHOENIX, NUVENIO HD, SOLARIS, NOVA| 192
NOW TV| NOW| 114
NSC| IM781R| 046
IM781| 047
OAK| SIGMA ONE, P1,P2,P3, SIGMA 2000| 037
RTC56, RKDM| 038
SIGMA 2001,2002| 039
SIGMA 450,500,550| 040
Optimum| Altice One| 237
Optimum| 236
PACE| 500 Series| 001 007
TDC Series| 002
DTA Series| 113
510| 004
DC550DR| 214
DC60X| 206
IPH8005M| 217
PANASONIC| 140,145,170,175| 030
110,120,130,150,160| 031
Pico Digital| VMX1| 224
PIONEER| VOYAGER Series| 001 007
MAKER(BRAND) NAME| CONVERTER|

CODE No

---|---|---
| BA9000| 013
BA4100,4200,4500| 028
BA-V1000| 029
REGENCY| ALL MODELS| 045
SAMSUNG| OCAP MODELS| 001 007
| 130
SEACHANGE| ANALOG CONVERTER| 190
HD TCM| 191
SKY| SKY+HD| 230
SKY HD| 204
Q| 240
AP HD, AP Jr| 241
SONY| DHG-M55CV| 003
Spectrum| Spectrum| 231
TECHNICOLOR| | 365
TELNET| RC-RW100| 154
THOMPSON| DCI1011GEM,DCI1011GEM1,DCI104ICS| 365 188
TILEVISION| TV19| 187
TOCOM| 5507| 035
5503A| 036
TRANSPARENT VIDEO SYSTEMS| 4000A| 193
Virgin Media| TIVO 6| 959
WEGENER| SMD 515| 050
WINDSTREAM| KINETIC| 212
ZeeVee| ZvMXE| 227
ZENITH| MN2500| 032
PM| 033
Z-TAC| 034

CABLE-DVR(TIVO)

TV

CODE NUMBER (3 DIGIT) LIST

---|---
AKIO| 103
AARON| 028
AMARK| 112 127
AMERICA ACTION| 043
AMPRO| 073 167
ANAM| 043 054 056 080 112 131
AOC| 058 070 004 112 245
APEX| 092
APEX DIGITAL| 015 150 037 724
AQUAVISION| 097 100 686
AUDIOVOX| 076 103 043 035 078 224
AUDIO| 689
AVIELO| 090 628
AVION| 223
Avera| 761
AXESS| 711
BAYSONIC| 043
BELL&HOWELL| 072
BENQ| 234
BRADFORD| 043
BROKSONIC| 096 170
CAIRN| 162
CANDLE| 070 002 003 004
CAPEHART| 058
CARVER| 164
CELEBRITY| 001
MEDTRONIC| 043
CIELO| 714
Civil| 732
GENERAL| 103 120
CITIZEN| 070 002 003 004 101 103 127
CLASSIC| 043
COBY| 640 641 671 236
CONCERTO| 004
CONTACT| 043 051
Continue-us| 161 746 747
CORONADO| 127
CRAIG| 043 054 028
CROSLEY| 164
CROWN| 043 127
CURTIS MATHES| 070 004 101 011 072 081 120 164 127
CXC| 043
DAEWOO| 076 103 112 004 127 016 043 044 125 120
DAYTON| 004 127
DELL| 041 249
DENON| 011
DIGITAL PROJECTION| 090
MAKER(BRAND) NAME| CODE NUMBER (3 DIGIT) LIST
---|---
DUMONT| 004 073
DWAIN| 131 132 161
DYNASTY| 043
DYNATECH| 062
FISHER| 007 057
ELECTRO BAND| 001
ELECTROHOME| 024 076 127
ELEMENT| 004 110 622 690
EMERSON| 005 028 043 048 076 096 155 004 051 151 153 154 127 121
ENVISION| 070
EPSON| 087 228
ESA| 031
Overview| 755
FREEMOTION| 688
FUJITSU| 164 197 028 157 149 066 217
FUNAI| 028 043 052 168
FUSION| 642
FUTURETECH| 043
GATEWAY| 165 031
GE| 070 073 130 144 160 161 004 008 009 034 056 074 155 081 120
GEM| 031
GIBRALTAR| 004 073
GOLDSTAR| 004 106 112 127
GPX| 674
GRUMPY| 028 043
HAIER| 004 116 623 236 749
HALLMARK| 004
HANNSPREE| 099
HARLEY DAVIDSON| 028
HARMAN KARDON| 164
HARVARD| 043
HISENSE| 198 021 619 630 631 236 752 749
HITACHI| 011 007 009 004 072 010 012 023 075 158 127 174 243 670 749
HP| 027 039 098
HUMAX| 122
HYPERION| 242
HYUNDAI| 049 067
ILO| 055 096
INFINITY| 164
INFOCUS| 046 215 225 233 726 733
INTEL| 129
INSIGNIA| 068 069 078 096 164 168 247
INTEQ| 073
JBL| 164
MAKER(BRAND) NAME| CODE NUMBER (3 DIGIT) LIST
---|---
JCB| 001
JCPENNEY| 004 008 024 030 065 070 101 160 127
JENSEN| 013
JVC| 038 001 034 083 195 159 227 639
KENWOOD| 070 001
KLEGG| 220
KLOSS| 002 059
KREISEN| 202
KTV| 070 043 154 127
LG| 004 106 112 127 086 236 648 741
LODGENET| 072
LOEWE| 196 164 738
LOGIK| 072
LUXMAN| 004
LXI| 007 015 052 081 160 164
MAGNAVOX| 070 003 004 022 059 060 061 063 064 127 164 094 160 056 028 035 211 205 218 050 138 232
MAJESTIC| 072
MARANTZ| 164 070 143 169
MATSUI| 164
MATSUSHITA| 080
MAXENT| 165
MEGATRON| 004
MEMOREX| 004 007 072 028 096
METZ| 088
MGA| 024 070 004 042
MIDLAND| 073
MINERVA| 088
MINTEK| 077
MINUTE| 008
MITSUBISHI| 109 024 042 004 040 146 028 124 081 200 235
MOTOROLA| 081
MTC| 070 004 062 101
MULTITECH| 043
NAD| 015 025
NEW| 070 130 134 040 056 007 019 024 004 182 140 717 758
NEXUS| 620 078
NIKKEI| 043
NIKKO| 103
NIKO| 175
NORCENT| 211
NTC| 103
NUVISION| 084
OLEVIA| 219 004 161 144 160
RANKING| 043
onn.| 898
MAKER(BRAND) NAME| CODE NUMBER (3 DIGIT) LIST
---|---
ONWA| 043
OPTIMUS| 080
OPTOMA| 029 032
OPTONICA| 019 081
ORION| 096 201 203 204 205 028
PANASONIC| 080 034 056 164 190 230 248 237 240 664 801
PEERLESS-AV| 723 763
PHILCO| 070 003 004 024 056 059 060 063 064 127 164
PHILIPS| 164 005 038 093 127 070 003 004 059 199 218 161 232 629 727 773
PIONEER| 023 025 135 176 004 018 070 183 191 208 214 182 660
PLANAR| 728 742 787 788
POLAROID| 026 118 119 006 110
PORTLAND| 004 103 127
PRISM| 034
PROSCAN| 144 160 161 167 236
PROTON| 004 058 171 173 193 127 163
PROTRON| 102 213 004 115
PROVIEW| 110
PROX| 092
PYLE HOME| 661 662
QUASAR| 034 056 239
RADIO SHACK| 004 019 127 043
RCA| 160 161 144 065 070 004 023 024 056 074 152 081 209 713 751
REALISTIC| 007 019
REVOLUTION HD| 220
RUNCO| 072 073 130 179 180 181 182 216 194 697
SAMPO| 070 004 058 165
SAMSUNG| 192 089 004 101 127 133 160 105 070 184 185 515 655
SANSEI| 120
SANSUI| 096 244 078 762
SANYO| 007 053 057 082 020 750
SCEPTRE| 036 699
SCOTCH| 004
SCOTT| 004 005 028 043 048 127 113
Sealoc| 897
SEARS| 004 007 015 028 030 057 082 094 160 052 164 127
SEIKI| 690
SELECO| 189
SEMIVOX| 043
SEMP| 015
SEURA| 704 797
SHARP| 081 019 014 028 004 022 127 684 692 735 765 766
SHERWOOD| 128
SIGNATURE| 072
Silo| 001
MAKER(BRAND) NAME| CODE NUMBER (3 DIGIT) LIST
---|---
Skyvue| 086
Skyworth| 895
SOLE| 177 178
SONY| 001 241 633 126 139
SOUNDESIGN| 003 004 028 043
SOYO| 163
SPECTRON| 112
SPECTRONIC| 004
SQUARE VIEW| 052
SSS| 004 043
STARLITE| 043
SUNBRITE| 633 634 635 236 238 772
SUPRE MACY| 002
SUPREME| 001
SVA| 046
SYLVANIA| 070 003 059 060 063 064 127 160 164 044 056 168 121 231
SYMPHONIC| 052 168
SYNTAX OLEVIA| 219 004 161 144 160
TANDY| 081
TATUNG| 056 062
TCL| 705 749
TECHNICS| 034 080
TECHNOL ACE| 028
TECH VIEW| 246
TECHWOOD| 004
TEKNIKA| 002 003 004 024 028 043 072 101 103 164 127
TELEFUNKEN| 244
TELERENT| 072
TERA| 172
THOMPSON| 166
TELEVISION| 663
TMK| 004
TNCI| 073
TOSHIBA| 015 030 007 040 062 101 142 045 137 703
TELEVISION| 127
TRUTECH| 212
UNIVERSAL| 008 009
UPSTART| 708
VENTURER| 236
VIDEO CONCEPTS| 146
VIDIKRON| 188 164 182
VTECH| 004
VIEWSONIC| 210 211 720
VIORE| 055 229 192
VISCO| 110
VIZIO| 236 031 624 004 625 675
WARDS| 004 064 164 008 009 019 028 060 061 063 072 074 070 127
W Box Technologies| 731
WESTINGHOUSE| 076 036 221 222 001 280 690 695
WINBOOK| 079
YAMAHA| 004 070 206 207
MAKER(BRAND) NAME|

CODE NUMBER (3 DIGIT) LIST

---|---
YORK| 004
YUPITERU| 043
ZENITH| 011 072 073 095 103 096
ZONDA| 112

DVD

MAKER(BRAND) NAME|

CODE NUMBER (3 DIGIT) LIST

---|---
ADCOM| 203
AIWA| 210 214
AKAI| 239
ALPINE| 179
ANTHEM| 361
APEX DIGITAL| 240 197 247 248 196
ARCAM| 165 148 374
AUDIOVOX| 075
BOSE| 244 245
CAMBRIDGE AUDIO| 224 145 360
CARY AUDIO DESIGN| 249 149
CLASSE| 242
COBY| 206
CYBERHOME| 170 212
DAEWOO| 170
DENON| 226 184 225 358
DUNE| 366
DURABRAND| 235
DYNEX| 089
EMERSON| 235
ESA| 235
FUNAI| 235
GE| 188 189
GOLDSTAR| 182 194
GO VIDEO| 228 182 252 253 254
GRADIENTE| 243
HARMAN KARDON| 217
HITACHI| 181
HITEKER| 197
INSIGNIA| 078 235 085 182 178 089 385
INTEGRA| 208 236 238 128
JVC| 185
KENWOOD| 166
KISS| 237
KLH| 230
KOSS| 243
KRELL| 218
MAKER(BRAND) NAME|

CODE NUMBER (3 DIGIT) LIST

---|---
LEXICON| 216
LG| 182 194 105 090
LITEON| 150
MAGNAVOX| 178 191 195 235 386
MARANTZ| 176 177 135
MCINTOSH| 167
MEMOREX| 222
MERIDIAN| 200
MINTEK| 240 196
MITO| 229
MITSUBISHI| 186
MOXI| 112
MYRYAD| 211
NAD| 198 182 092
ONKYO| 207 236 128
OPPO| 125
OPTIMUS| 187
ORION| 243
PANASONIC| 076 219 173 184 192 103 104 379
PARASOUND| 083
PHILIPS| 164 074 209 176 177 191 195 127 381 387
PIONEER| 187 180 175 221 223 093 364 156 377
POLAROID| 075 084 085
PRIMARY| 250 251
PROCEED| 172
PROSCAN| 188 189
RCA| 188 189 086
SANSUI| 201
SANYO| 215
SAMSUNG| 183 228 193 205 073 152 241 380
SENSORY SCIENCE| 254 255
SHARP| 174
SHERWOOD| 083 129 361
SONY| 077 190 213 168 118 119 120 121 126 091 363 368 378 382
SPECTRONIC| 088
SUPERSCAN| 235
SV2000| 235
SYLVANIA| 235
SYMPHONIC| 235
TAG McLaren| 202
TASCAM| 185
TECHNICS| 173
THETA DIGITAL| 187
TOSHIBA| 169 171 191 206 227 201 236 356
---|---
TRUTECH| 151
VENTURER| 229
VINCE| 220 087
VIZIO| 375
YAMAHA| 199 204 246 184 192 334 383
ZENITH| 182 194

*Note: ForTV/DVDcombinationunits, Please use the following step to operate the volume control.

STEP 1 Press the [CBL] button and the [OK/SEL] button simultaneously for 3 seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on.
STEP2 Press the [VOL5] button.
STEP3 Press the [DVD] button. The CBL device LED will blink twice to confirm the programming.

References

• URC Automation | Think Beyond Everyday

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>