nutribullet NBJ200G 800W Fruit and Vegetable Juicer User Guide
- June 5, 2024
- nutribullet
Table of Contents
- nutribullet NBJ200G 800W Fruit and Vegetable Juicer
- Important safeguards
- What’s included
- Assembly guide
- Assembly
- Usage instructions
- Control dial
- Juicing tips
- Disassembly
- Care & maintenance
- Juice & unit storage
- Troubleshooting guide
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
nutribullet NBJ200G 800W Fruit and Vegetable Juicer
Important safeguards
Warning! To avoid the risk of serious injury, carefully read all instructions before operating your nutribullet Juicer™. When using any electrical appliance, basic safety precautions should always be observed, including the following important information.
PERSONAL SAFETY
WARNING!
This juicer system has sharp blades and moving parts, and is NOT intended
for use by children who lack experience and knowledge of its safe operation.
They require close supervision and thorough instruction on its proper use and
safe operation. Keep the appliance and its cord out of reach of children.
Children shall not play with the appliance. To eliminate a choking hazard for
young children, remove and safely discard the protective cover fitted to the
power plug of this juicer.
AVOID CONTACT WITH MOVING PART S.
Keep hands, fingers, hair, clothing as well as spatulas and other utensils
away from the appliance during operation.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
SIEVE AND BLADES ARE SHARP! HANDLE WITH EXTREME CARE!
-
Do not touch the small cutting blades/teeth on the bottom/base of the sieve. Keep fingers away from the sharp blade in the feed chute.
-
Do not leave the appliance unattended when in use.
-
Hard fruits and vegetables will put excess strain onto the motor if a low speed is selected.
-
If there is a spill under, around or onto the juicer itself, disconnect the unit from the power source. Clean with a cloth and allow unit to dry completely before operating.
-
Do not push food into the feed chute with your fingers or utensils. Only use the food pusher provided. Do not place your hand or fingers into the feed chute when it is attached to the juicer. If food becomes lodged in the feed chute, use the food pusher provided or another piece of fruit or vegetable to push it down. Turn the motor off and ensure that all moving parts have stopped before disassembling the juicer to remove the remaining pulp.
-
Do not operate this or any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
-
CAUTION: In order to avoid
a hazard due to inadvertent resetting of the thermal cut- out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility. -
Do not use the appliance if the rotating sieve or the protecting cover is damaged or has visible cracks.
Always ensure the juicer is turned OFF after each use. Before disassembling, make sure the sieve has stopped rotating and the motor has completely stopped.
PRODUCT SAFETY
- This juicer is only designed to juice fruits and vegetables. Please refer to the juicing guide to determine the correct speed for the fruits and vegetables selected for juicing.
- Do not use any frozen fruits or vegetables.
- Do not use the juicer without the pulp basin and basin lid attached to the motor base. Please see assembly instructions for proper placement.
- Remove and safely discard any packaging material or promotional labels before using the juicer for the first time.
- Ensure that the surface where the appliance operates is stable, level, clean and dry.
- Remove rind from all citrus fruits before juicing.
- Do not juice stone fruit unless pits of the seed stone has been removed.
- Always make sure the pulp basin cover is clamped securely in place (with locking handle) before the motor is turned on. Do not unfasten the clamps (locking handle) while the juicer is in operation.
- When using this juicer, make sure there is adequate air space around and under it for proper air circulation.
- The use of attachments not recommended or sold by nutribullet® may cause fire, electric shock or injury. This juicer is for household use only. Do not use this juicer for anything other than its intended use. Do not use in moving vehicles or boats. Do not use outdoors. Misuse may cause injury.
- If no speed is selected after 10 minutes, the unit will power off.
- If the motor stops for any reason, unplug the power base and let it cool for at least 15 minutes.
- Turn the juicer OFF, then unplug from the outlet when not in use, before assembling or disassembling parts and before cleaning. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.
- Do not let the power cord hang over the edge of a table or countertop.
- Do not let the power cord touch hot surfaces, such as a stove or let it become tangled or knotted.
- Regularly inspect the power cord, plug, and the actual juicer for any damage.
- To protect against fire, electrical shock, and injury to persons, do not immerse the juicer, Motor Base, cord or plug in water or any other liquid.
- Do not use the juicer if the rotating sieve is damaged.
- Keep the juicer clean. Refer to care and cleaning section for further information.
WARNING!
- Vibration can occur during normal operation.
- If extreme vibration occurs, discontinue use and call Customer Service.
- Any maintenance other than cleaning should be performed by an authorized electrician. Do not attempt to repair or service the juicer, contact Customer Service for assistance at www.nutribullet.com
What’s included
Assembly guide
Assembly
-
Place the Motor Base on a dry, level counter top. Ensure the dial is set to the “OFF” position and the unit is unplugged.
-
Place the Pulp Basin on top of the Motor Base. Align the Pulp Basin with the Motor Base so that the spout is aligned with the dimpled side of the Motor Base.
-
Align the Sieve with the motor drive coupling and push down until it clicks into place. Handle the Sieve by gripping the top edges being careful not touch the sharp teeth on the base of the Sieve. Ensure the Sieve is properly seated in place and securely inside of the Pulp Basin.
-
Place the Basin Cover over the Sieve and Pulp Basin. The side “ears” on the Basin Cover should align with the “ears” on the sides of the Pulp Basin.
-
Raise the Locking Handle and move it into the “ears” on each side of the Basin Cover. The Locking Handle should be in a vertical position and locked into place.
NOTE: if the Locking Handle is not securely in place, the juicer will not power on. -
Swing the No-Drip Spout cover up vertically, so that it is no longer covering the juice spout.
-
Place the Juice Pitcher Lid on top of the Juice Pitcher and open the locking lid latch.
-
Slightly angle the Juice Pitcher and place it under the juice spout. Align the spout with the hole in the Juice Pitcher Lid and level out the Juice Pitcher. It will fi t snuggly into the spout to hold it in place.
Usage instructions
-
Gather all of your desired ingredients and wash them. Prepare the ingredients to be juiced by cutting, skinning, or removing the rind, stems, or stone seeds.
-
After the juicer is fully assembled, plug the power cord into an outlet. Use the Dual-Speed Control Dial to select a speed to begin juicing. You can toggle between speeds as desired depending on the type of produce. (Refer to the chart on page 14 for recommended speeds for diff erent types of produce).
-
While the motor is running, begin gently guiding your ingredients into the feed chute using the Food Pusher.
NOTE: Do not use excess force or speed when pushing food down with the Food Pusher, as it will not allow for maximum juice yield.
WARNING: Never use hands/fi ngers or other tools to push food down the feed chute into the Sieve. Only the Food Pusher should be used to push down ingredients. -
Juice will begin to fl ow out of the spout and into the Juice Pitcher, while the pulp will be separated and stored in the Pulp Basin.
-
When the Pulp Basin is completely full, it must be emptied before you continue juicing. See disassembly instructions.
-
Always be sure to turn the Dual-Speed Control Dial to the “OFF” position and wait for the Sieve to stop spinning before removing the Juice Pitcher from under the spout. Unplug the unit after each use.
-
Remove the Juice Pitcherv from under the spout. You may close the Juice Pitcher Lid and store juice in the Juice Pitcher if desired.
NOTE: To do this, you’ll fi rst need to tip the Juice Pitcher forward at a slight angle, so that the lid’s large hole has some separation from the spout, then you can slide out the pitcher. This is the reverse of what you did during assembly. -
Immediately move the No- Drip Spout cover downward over the spout to avoid any residual drips onto the unit or onto the surface below the juicer.
TIP: We recommend using your left hand to pull the Juice Pitcher away, while using your right hand to swing the No-Drip Spout cover down and over the spout opening.
Control dial
DUAL-SPEED CONTROL DIAL & JUICING SETTINGS
-
OFF:
Power is OFF, the juicer is not running. -
LOW:
Best for juicing softer fruits and vegetables. -
HIGH:
Best for harder produce like carrots and beets.
Juicing tips
JUICING SPEED SELECTION GUIDE
INGREDIENTS | SPEEDS | SEASONS | VITAMINS / NUTRIENTS | |
---|---|---|---|---|
Apple | High | All Year | source of quercetin | |
Beets | High | Summer / Fall / Winter | excellent source of folate | |
Blueberry | High | Summer | good source of vitamin C | |
Broccoli | High | Fall / Spring | high in vitamin C, high in folate, good |
source of potassium
Brussels Sprouts| High| Fall / Winter| high in vitamin C, good
source of folate
Cabbage| Low| Fall / Winter / Spring| | high in vitamin C
Carrots| High| All Year| excellent source of vitamin A, good source of
vitamin C
Cauliflower| High| Fall| | high in vitamin C, good source of folate
Celery| High| All Year| good source of vitamin C, good source of vitamin
A
Cucumber| Low| Summer| | good source of vitamin C
Fennel| High| All Year| good source of vitamin C and potassium
Ginger| High| Fall| | contains vitamin C, magnesium, and potassium
Grapes| Low| Fall| good source of vitamin K
Grapefruit| Low| Winter| | high in vitamin A, high in vitamin C
Kale| High| Fall / Winter / Spring| excellent source of vitamin A and
vitamin C, good source of calcium and potassium
Kiwi| Low| Fall / Winter / Spring| | high in vitamin C, good source of
potassium and vitamin E
Lemon| Low| All Year| high in vitamin C
Lime| Low| All Year| | high in vitamin C
Melons (all)| Low| Summer| high in vitamin A, high in vitamin C
Orange| High| Winter| | high in vitamin C
Peaches| Low| Summer| good source of vitamin C
Pears| High| Fall / Winter| | good source of vitamin C
Pineapple| High| Fall / Winter / Spring| high in vitamin C
Plums| High| Summer| | good source of vitamin C
Raspberries| Low| Summer / Fall| high in vitamin C
Spinach| Low| Fall / Spring| | high in vitamin A, vitamin C, iron, and
folate, good source of magnesium
Sweet Potato (raw)| High| Fall / Winter| good source of
potassium, high in vitamin A and vitamin C
Tomatoes| Low| Summer| | high in vitamin A, high in vitamin C, good
source of potassium
PROPER PRODUCE PREP
Prepare fruit and veggies before inserting them into the juicer:
- Properly clean produce (rinse with lukewarm water, produce wash, or water and apple cider vinegar).
- Peel or remove skin as needed, and chop food items down to the right size – just small enough to fit easily into the feed chute, without having to force the pieces down with the Food Pusher.
- Remove rind from all citrus fruits before juicing.
- Remove large pits and seeds from stone fruits before juicing.
FEED CHUTE
- Never place your hand or fingers into the feed chute when it is attached to the appliance.
- Always start the juicer before adding food to the feed chute. The juicer must be running when items enter it.
- Do not overload the feed chute. Items must be added gradually, at a pace the juicer can keep up with.
- Use only the provided Food Pusher to push food into the feed chute. Never use fingers, utensils, or any other apparatus.
- Never use excessive force to push items into the feed chute.
- When juicing, ensure all produce has moved through the feed chute and into the Sieve before adding more.
- If any food gets stuck in the feed chute, use the Food Pusher to move it down the chute and into the Sieve.
CONSUMING JUICE & PULP
Instead of composting or throwing away the pulp left over after juicing, you
can choose to consume it. See our Recipe Guide for some fun tips on what to do
with the pulp. By using these creative ideas, you can enjoy pulp in a variety
of delicious (and healthy) ways.
- Whether you prefer sweet or savory, you can use pulp to create some tasty treats!
- For best taste,consume fresh juice and pulp within 48 hours of juicing.
NO-GO FOODS
Foods that should NEVER be used in this juicer:
- Foods that do not contain juice to extract (for example, bananas or avocados).
- Frozen fruits or vegetables.
- Stone fruits that have large pips or seeds that have not been removed. Stone fruits may be used only if the seed or pip has been removed.
OVERHEATING
- If the motor overheats, the juicer will turn off.
- If the juicer stops working, unplug it and allow it to cool down for at least fifteen minutes before attempting to use again.
Disassembly
- Ensure the unit is powered down, turned “OFF”, and unplugged.
- Remove the pitcher from under the spout. To prevent drips use the No-Drip Spout cover to close the juice spout.
- Unlock the Locking Handle from the Basin Cover by pulling the handle backward out of the “ears” on either side of the Basin Cover. Move the handle down.
- Remove the Pulp Basin from the Motor Base by pulling upwards with the Basin Cover and Sieve still in place, and take it directly to your sink.
- Remove the Food Pusher by lifting it out of the feed chute.
- Lift the Basin Cover vertically off of the Pulp Basin and remove any pulp from the inside of the cover. You may use the fl at end of the Cleaning Brush to scrape pulp off of the cover.
- Gently lift the Sieve vertically out of the center of the Pulp Basin. Clean the Sieve right away (see care instructions).
- Empty the Pulp Basin. Use the fl at end of the Cleaning Brush to easily scrape out the pulp and set it aside for use in other recipes or composting. You can also empty the pulp into your waste bin or compost.
Care & maintenance
Please follow the below cleaning instructions before the first use, and after
each use.
Cleaning the nutribullet Juicer Pro™ is quick and easy. All components except
for the Food Pusher and Motor Base are dishwasher safe. Read on for some
cleaning tips and best practices.
-
Always ensure the Motor Base is unplugged before you begin assembly, disassembly, cleaning or storage of the unit.
-
Once the Pulp Basin is emptied, rinse all parts under running water.
-
Use the Cleaning Brush to scrub the Sieve under running water. Be sure to properly clean the Sieve every time you juice, as minerals from fruits and vegetables can cause build-up in the Sieve which may prohibit maximum juice extraction.
WARNING: Always use precaution when cleaning the Sieve, as it contains sharp blade teeth on the flat disc part.
TIP: Always clean the Sieve as soon as possible after juicing using the Cleaning Brush. If allowed to sit, pulp will dry on the Sieve and it will become more difficult to scrub blocked holes. If this happens, be sure to allow the Sieve to soak in hot water for 30 minutes. -
All Juicer Pro components except the Motor Base are dishwasher safe. You may also hand wash with warm soapy water.
TIP: Do not use the Sterilize cycle on your dishwasher to clean your juicer as it may cause parts to deform. -
Wipe down Motor Base with a clean, damp cloth.
WARNING: Never submerge Motor Base into water or other liquid.
Cleaning instructions for your nutribullet Juicer Pro™ storage accessories:
- Glass Storage Bottles and lids are dishwasher safe.
- Freezer Trays and lids are dishwasher safe.
Juice & unit storage
Included with your Juicer Pro are some great storage accessories: a Juice Pitcher, two Juice Storage Bottles, and two Freezer Trays.
The storage accessories give you three options for storing juice:
-
IN THE PITCHER:
The Juice Pitcher stores up to 800 ml. Make sure to store the pitcher upright in your refrigerator, with lid tightly sealed, latch closed, and nothing atop the lid. -
IN THE BOTTLES:
Use each Storage Bottle to save up to 350 ml of juice, so you can enjoy it later — either at home or on the go. Fill up the bottles leaving about .6 cm of room at the top, leaving just enough air in the bottle. -
IN THE TRAYS:
Each Freezer Tray holds a total of 470 ml: one tray has eight 60 ml wells, and the other tray has four 120 ml wells. These are a great way to preserve juice longer-term, then defrost it anytime for a full drinkable portion. Or, use the trays to make frozen juice shots. (See our Recipe Guide for some inspiring recipes for frozen juice shots to add to your favorite beverages, or to drink on their own.)
For best taste, consume fresh juice and pulp within 48 hours of juicing.
Do not place anything on top of the Pitcher Lid when storing in the
refrigerator.
Store remaining pieces of the unit in a safe place where they will not be
damaged and won’t cause harm as some pieces are sharp!
Troubleshooting guide
-
PROBLEM: The power button flashes three times and then remains illuminated when I select a speed.
SOLUTION: This means that the unit is not properly assembled. Ensure the Pulp Basin is properly seated on top of the Motor Base, and the Locking Handle is locked into place. -
PROBLEM: The juicer stopped in the middle of juicing, and the power button flashed.
SOLUTION: Ensure the Locking Handle is securely locked into place. -
PROBLEM: The juicer stopped in the middle of juicing, and the power button remains illuminated.
SOLUTION: You have exceeded 10 minutes of continuous running time. Unplug the juicer and keep the unit off for 15 minutes before continuing use. -
PROBLEM: The juicer has stopped running, and all lights flashed three times.
SOLUTION: The juicer has overheated. Unplug the unit and allow it to cool down for 15 minutes before continuing use.
Explanation of the markings
- This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal; recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
- This product complies with the European regulation no. 1935/2004 on materials and articles intended to come into contact with food.
Replacement parts
To order additional parts and accessories, please visit our website at
nutribullet.com
1 800-523-5993 |
nutribullet.com
nutribullet® is the registered trademark of CAPBRAN HOLDINGS, LLC Copyright ©
2020 CAPBRAN HOLDINGS, LLC. Distributed by CAPITAL BRANDS DISTRIBUTION, LLC.
LOS ANGELES, CA 90025 USA
All Rights Reserved. MADE IN CHINA
Illustrations may differ from the actual product. We are constantly striving
to improve our products, therefore the specifications contained herein are
subject to change without notice.
210927_NBJ93100
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>