Shelly RGBW2 Smart WiFi LED Controller User Guide
- June 5, 2024
- Shelly
Table of Contents
Shelly RGBW2 Smart WiFi LED Controller
Specification
The RGBW 2 WiFi LED Controller Shelly® by Allterco Ro botics is intended to be installed directly to a LED strip/ light in order to control the color and dimming of the light Shelly may work as a standalone device or as an accessory to a home automation controller
- Power supply: 12 or 24V DC
- Power output
- 144W combined power
- 75W per channel
- Power output
- 288W combined power
- 150W per channel
- Complies with EU standards:
- RE Directive 2014/53/EU
- LVD 2014/35/EU
- EMC 2004/108/WE
- RoHS 2 2011/65/UE
- Working temperature: from 2020°C to 4040°C
- Radio signal
- power: 1mW
- Radio protocol:
- WiFi 802.11 b/g/n Frequency: 2400 2500 MHz;
- Operational range (depending on local construction):
- up to 20 m outdoors
- up to 10 m indoors
- Dimensions (HxWxL): 43 x 38 x 14 mm
- Electrical consumption: < 1 W
Technical Information
- Control through WiFi from a mobile phone, PC, automation system or any other Device supporting HTTP and/or UDP protocol.
- Microprocessor management.
- Controlled elements: multiple white and colour (RGB) LED diods.
- Shelly may be controlled by an external button/switch.
CAUTION! Danger of electrocution. Mounting the Device to the power grid
has to be performed with caution.
CAUTION! Do not allow children to play with the button/ switch connected
the Device. Keep the Devices for remote control of Shelly (mobile phones,
tablets, PCs) away from children.
Introduction to Shelly®
Shelly® is a family of innovative Devices, which allow remote control of
electric appliances through mobile phone, PC or home automation system.
Shelly® uses WiFi to connect to the devices controlling it. They can be in the
same WiFi net-work or they can use remote access (through the Internet).
Shelly® may work standalone, without being managed by a home automation
controller, in the local WiFi network, as well as through a cloud service,
from everywhere the User has Internet access.
Shelly® has an integrated web server, through which the User may adjust,
control and monitor the Device. Shelly® has two WiFi modes – access Point (AP)
and Client mode (CM). To operate in Client Mode, a WiFi router must be located
within the range of the Device. Shelly® devices can communicate directly with
other WiFi devices through HTTP protocol.
An API can be provided by the Manufacturer. Shelly® devices may be available
for monitor and control even if the User is outside the range of the local
WiFi network, as long as the WiFi router is connected to the Internet. The
cloud function could be used, which is activated through the web server of the
Device or through the settings in the Shelly Cloud mobile application.
The User can register and access Shelly Cloud, using either Android or iOS
mobile applications, or any internet browser and the web site:
https://my.Shelly.cloud/.
Installation Instructions
CAUTION! Danger of electrocution. The mounting/ installation of the
Device should be done by a qualified person(electrician).
CAUTION! Danger of electrocution. Even when the Device is turned off, it
is possible to have voltage across its clamps. Every change in the connection
of the clamps has to be done after ensuring all local power is powered off/
disconnected.
CAUTION! Do not connect the Device to appliances exceeding the given max
load!
CAUTION! Connect the Device only in the way shown in these instructions.
Any other method could cause damage and/or injury.
CAUTION! Before beginning the installation please read the accompanying
documentation carefully and completely. Failure to follow recommended
procedures could lead to malfunction, danger to your life or violation of the
law. case of incorrect installation or operation of this Device.
RECOMMENDATION Тhe Device may be connected to and may control electric
circuits and appliances only if they comply with the respective standards and
safety norms
RECOMMENDATION The Device may be connected to and may control electric
circuits and light sockets only if they comply with the respective standards
and safety norms
Initial Inclusion
Before installing/mounting the Device ensure that the grid is powered off
(turned down breakers).
Connect the Shelly to the power grid following the wiring scheme above (fig 1
You may choose if you want to use Shelly with the Shelly Cloud mobile
application and Shelly Cloud service You can also familiarize yourself with
the in structions for Management and Control through the embed ded Web
interface
Control your home with your voice
All Shelly devices are compatible with Amazon Echo and
Google Home. Please see our step by step guide on:
https://shelly.cloud/compatibility/Alexa
https://shelly.cloud/compatibility/Assistant
Shelly Cloud gives you opportunity to control and adjust all Shelly ® Devices
from anywhere in the world. You only need an internet connection and our
mobile application, installed on your smartphone or tablet. To install the
application please visit Google Play (Android fig. 2) or App Store (iOS fig.
3) and install the Shelly Cloud app.
Registration
The first time you load the Shelly Cloud mobile app, you have to create an account which can manage all your Shelly ® devices.
Forgotten Password
In case you forget or lose your password, just enter the e mail address you
have used in your registration You will then receive instructions to change
your password
WARNING! Be careful when you type your e mail address during the
registration, as it will be used in case you forget your password.
After registering, create your first room (or rooms), where you are going to
add and use your Shelly devices.
Shelly Cloud gives you opportunity to create scenes for auto matic turning on or off of the Devices at predefined hours or based on other parameters like temperature, humidity, light etc ..(with available sensor in Shelly Cloud) Shelly Cloud allows easy control and monitoring using a mo bile phone, tablet or PC
Device Inclusion
To add a new Shelly device, install it to the power grid following the Installation Instructions included with the Device
-
Step1 After the installation of Shelly and the power is turned on Shelly will create its
own WiFi Access Point (AP).
WARNING
In case the Device has not created its own WiFi network with SSID like shellyrgbw 2 35 FA 58 check if you have connected Shelly correctly by the scheme in Fig 1 If you do not see an active WiFi network with SSID like shellyrgbw 2 35 FA 58 reset the Device If the Device has been powered on, you have to power it off and on again After turning the power on, you have 20 seconds to press 5 consecutive times the switch connected DC ( Or if you have physicall access to the Device, press the reset button once The LED strip light will begin to flash After the device has began to flash, turn the power off and back on again Shelly should return to AP Mode If not, please repeat or contact our customer support at support@Shelly.cloud -
Step 2
Choose “Add Device”. In order to add more Devices later, use the app menu at the top right corner of the main screen and click “Add Device” Type the name ( and password for the WiFi network, to which you want to add the Device -
Step 3
If using iOS: you will see the following screen:
Press the home button of your iPhone/iPad/iPod Open Settings WiFi and connect to the WiFi network created by Shelly, e g shellyrgbw 2 35 FA 58 If using Android your phone/tablet will automatically scan and include all new Shelly Devices in the WiFi network that you are connected to
Upon successful Device Inclusion to the WiFi network you will see the following pop up: -
Step 4:
-
Work
Modes Shelly RGBW 2 has two work modes Color and White -
Color
In Color mode you have a full color gamma to choose the desired color fro Under the color gamma you have 4 pure predefined colors Red, Green, Blue Yellow Below the predefined colors you have the dimmer slider from which you can vary the Shelly RGBW 2 `s brightness -
White
In White mode you have four separate channels, each with On/Off button and a dimmer slider from which you can set the desired brightness for the corresponding channel of Shelly RGBW 2
Edit Device From here you can edit -
Device Name
-
Device Room
-
Device Picture
When you are done, press Save Device -
Timer
Тo manage the power supply automatically, you may use: Auto OFF: After turning on, the power supply will automatically shutdown after a predefined time (in seconds). A value of 0 will cancel the automatic shutdown.
Auto
ON After turning off, the power supply will be automatically turned on after a predefined time (in seconds) A value of 0 will cancel the automatic power on Weekly Schedule
This function requires an Internet connection
To use Internet, a Shelly Device has to be connected to a local WiFi network with working internet connection. Shelly may
turn on/off automatically at a predefined time. Multiple schedules are possible. Sunrise/Sunset
This function requires an Internet connection.
Shelly receives actual information through the Internet about the time of sunrise/sunset in your area Shelly may turn on or off automatically at sunrise/sunset, or at a specified time before or after sunrise/sunset Multiple schedules are possible Internet/Security WiFi
Mode Client Allows the device to connect to an available WiFi network After typing the details in the respective fields, press Connect WiFi
Mode Acess Point Configure Shelly to create a Wi Fi Access point After typing the details in the respective fields, press Create Access Point
Cloud: Enable or Disable connection to the Cloud service. Restrict Login: Restrict the web interface of Shely with a Username and Password. After typing the details in the respective fields, press Restrict Shelly.
-
-
Settings
Power On Default Mode
This sets the default output state when Shelly is powered.
ON: Configure Shelly to turn ON, when it has power.
OFF: Configure Shelly to turn OFF, when it has power. Restore Last Mode: Configure Shelly to return to last state it was in, when it has power.
Firmware Update
Update the firmware of Shelly, when a new version is released.
Time
Zone and Geo location Enable or Disable the automatic detection of Time Zone and Geo location.
Factory Reset Return
Shelly to its factory default settings.
Device Information
Here you can see the:- Device ID Unique ID of Shelly
- Device IP The IP of Shelly in your Wi Fi network
The Embedded Web Interface
Еven without the mobile app, Shelly can be set and controlled through a
browser and WiFi connection of a mobile phone, tablet or PC
ABBREVIATIONS USED:
Shelly ID the unique name of the Device It consists of 6 or more characters It
may include numbers and letters, for example 35 FA 58
SSID the name of the WiFi network, created by the Device, for example
shellyrgbw 2 35 FA 58 Access Point ( the mode in which the Device creates its
own WiFi connection point with the respective name ( Client Mode ( the mode in
which the Device is connect ed to another WiFi network
Initial inclusion
-
Step 1
Install Shelly to the power grid following the schemes de scribed above and urn it on Shelly will create its own WiFi network (
WARNING : In case the Device has not created its own WiFi network with SSID like shellyrgbw2 35FA58 check if you have connected Shelly correctly by the scheme in Fig. 1. If you do not see an active WiFi network with SSID like shellyrgbw2 35FA58 , reset the Device. If the Device has been powered on, you have to power it off and on again. After turning the power on, you have 20 seconds to press 5 consecutive times the switch connected DC (SW). Or if you have physicall access to the Device, press the reset button once.
The LED strip light will begin to flash. After the device has began to flash, turn the power off and back on again. Shelly should return to AP
Mode. If not, please repeat or contact our customer support at: support@Shelly.cloud -
Step 2
When Shelly has created an own WiFi network (own AP), with name ( such as shellyrgbw 2 35 FA 58 Connect to it with your phone, tablet or PC -
Step 3
Type 192.168.33.1 into the address field of your browser to load the web interface of Shelly.
Home Page
This is the home page of the embedded web interface. If it has been set up is correctly, you will see information about:
- Current work mode color or white
- Current state (on/
- Current brightness level
- Power button
- Connection to Cloud
- Present time
- Settings
Тo manage the power supply automatically, you may use:
Auto OFF After turning on, the power supply will automatically shutdown after
a predefined time (in seconds) A value of 0 will cancel the automatic shutdown
Auto ON After turning off, the power supply will be automatically turned on
after a predefined time (in seconds) A value of 0 will cancel the automatic
power on
Weekly Schedule
This function requires an Internet connection To use Internet, a Shelly Device
has to be connected to a local WiFi network with working internet connection.
Shelly may turn on/off automatically at a predefined time. Multiple schedules
are possible.
Sunrise/Sunset
This function requires an Internet connection. Shelly receives actual
information through the Internet about the time of sunrise/sunset in your
area. Shelly may turn on or off automatically at sunrise/sunset, or at a
specified time before or after sunrise/sunset Multiple schedules are possible
Internet/Security
WiFi Mode Client Allows the device to connect to an avail able WiFi network
After typing the details in the respective fields, press Connect
WiFi Mode Acess Point Configure Shelly to create a Wi Fi Access point After
typing the details in the respective fields, press Create Access Point
Cloud Enable or Disable connection to the Cloud service Restrict Login
Restrict the web interface of Shely with a User name and Password After typing
the details in the respective fields, press Restrict Shelly
ATTENTION!
If you have entered incorrect information (wrong settings, usernames,
passwords etc you will not be able to connect to Shelly and you have to reset
the Device
WARNING : In case the Device has not created its own WiFi
network with SSID like shellyrgbw 2 35 FA 58 check if you have connected
Shelly correctly by the scheme in Fig 1 If you do not see an active WiFi
network with SSID like shellyrgbw 2 35 FA 58 reset the Device If the Device
has been powered on, you have to power it off and on again After
turning the power on, you have 20 seconds to press 5 consecutive times the
switch connected DC ( Or if you have physically access to the Device, press
the reset button once.
The LED strip light will begin to flash. After the device has began to flash,
turn the power off and back on again. Shelly should return to AP Mode. If not,
please repeat or contact our customer support at:
support@Shelly.cloud
Advanced Developer Settings: Here you can change the action execution:
- Via CoAP
- Via MQTT
Firmware
Upgrade Shows present firmware version If a newer version is available,
officially announced and published by the Manufacturer, you can update your
Shelly Device Click Upload to install it to your Shelly Device
Settings
Power On Default Mode
This sets the default output state when Shelly is powered.
ON: Configure Shelly to turn ON, when it has power.
OFF: Configure Shelly to turn OFF, when it has power. Restore Last Mode:
Configure Shelly to return to last state it was in, when it has power.
Time Zone and Geo location Enable or Disable the automatic detection of Time
Zone and Geo location.
Firmware Update: Update the firmware of Shelly, when a new version is
released.
Factory Reset : Return Shelly to its factory default settings.
Device Reboot: Reboots the device.
Device Information Here you can see the unique ID of Shelly.
Additional Features
Shelly allows control via HTTP from any other device, home automation controller, mobile app or server. For more information about the REST control protocol, please visit: https://shelly.cloud/developers/ or send a request to:
Environmental Protection
This marking on the device, accessories, or documentation indicates that the device and its electronic accessories ( USB cable) must be disposed only in specially designated locations This marking on the battery, the instruction manual, the safe ty instructions, the warranty card or the packaging indicates that the battery in the device must be disposed only in specially designated locations Please follow the instructions for environmental protection and proper disposal of the Device, its accessories, and its packaging for the recycling of the materials for their further usage and to keep the environment clean!
Warranty Terms
-
The Device’s warranty term is 24 (twenty four) months, beginning since the date of purchase by the End User The Manufacturer does is not responsible for extra warranty terms by the Еnd Seller
-
The Warranty is valid for the territory of EU The warranty is applicable in compliance with all relevant laws and users’ rights protections The purchaser of the Device is entitled to exercise his/ her rights in accordance with all applicable laws and regulations
-
Warranty terms are provided by Allterco Robotics EOOD (referred
hereinafter as the Manufacturer), incorporated under the
Bulgarian law, with address of registration 109 Bulgaria Blvd,
floor 8 Triaditsa Region, Sofia 1404 Bulgaria, registered with the
Commercial Register kept by the Bulgarian Ministry of Justice’s
Registry Agency under Unified Identity Code ( 202320104 -
Claims regarding the Conformity of the Device with the terms of the contract of sale shall be addressed to the Seller, in accordance with its terms of sale
-
Damages such as death or body injury, deterioration or damages to objects different from the defective product, caused by a defective product, are to be claimed against the Manufacturer using the contact data of the Manufacturer’s company
-
The User may contact the Manufacturer at support@shelly.cloud for operational problems that may be resolved remotely It is recommended that the User contact the Manufacturer before sending it for servicing
-
The terms of removing defects depends on the commercial terms of the Seller
The Manufacturer is not responsible for untimely servicing of the Device or for faulty repairs carried out by unauthorized service -
When exercising their rights under this warranty, the User must provide the Device with the following documents receipt and valid warranty card with date of purchase
-
After a warranty repair has been carried out, the warranty period is extended only for that period
-
The warranty does NOT cover any damages to the Device which occur in the following circumstances
- When the Device has been used or wired inappropriately, including inappropriate fuses, overpassing maximal values of load and current, electric shock, short circuit or other problems in the power supply, the power grid or the radio network
- When there is a non compliance between warranty card and/ or without a purchase receipt, or attempted forgery of these documents, including (but not limited to) the warranty card or the documents proving the purchase
- When there has been a self repair attempt, attempt,(de) modification, or adaptation of the Device by unauthorized per sons
- Intentional or negligent improper handling, storing or trans potation of the Device, or in the event of non observance of the instructions included in this warranty
- When a non standard power supply, network, or faulty Devices have been used
- When damages occur which were caused regardless of the Manufacturer, including but not limited to floods, storms, fire, lightning, natural disasters, earthquakes, war, civil wars, other force majeure, unforeseen accidents, robbery, water damage, any damages made by ingress of liquids, weather conditions, solar heating, any damages made by intrusion of sand, humidity, high or low temperature, or air pollution
- When there are other reasons beyond manufacturing defect, including but not limited to water damage, ingress of liquid into the Device, weather conditions, solar overheating, intrusion of sand, humidity, low or high temperature, air pollution ..[u 1
- When there have been mechanical damages (forced opening, breaking, cracks, scratches or deformations) caused by a hit, fall, or from another object, wrong use, or caused by not following the instructions for use
- When damage has been caused by exposing the Device to severe outdoor conditions such as high humidity, dust, too low or too high temperature Terms of proper storage are specified in the User Manual
- When damage has been caused by lack of maintenance by the User, as specified in the User manual
- When damage has been caused by faulty accessories, or those not recommended by the Manufacturer
- When damage has been caused by the use of non original spare parts or accessories not suitable for the specified Device mod el, or after repairs and changes carried out by an unauthorized service or person
- When damage has been caused by the use of faulty Devices and/or accessories
- When damage has been caused by faulty software, a computer virus or other harmful behavior on the Internet, or by lack of software updates or incorrect updates by a method not provided by either the Manufacturer or by the Manufacturer’s software
-
The range of warranty repairs does not include periodical maintenance and inspections, particularly cleaning, adjustments, checks, bug fixes or program parameters and other activities that must be performed by the User ( The warranty does not cover wear of the Device, because such elements have a limited lifespan
-
The Manufacturer is not responsible for any property dam age caused by a defect in the Device The Manufacturer is not liable for indirect damages (including but not limited to loss of profits, savings, lost profits, claims by third parties) in connection with any defect of the Device, nor for any property damage or personal injury arising out of or related to the use of the Device
-
The Manufacturer is not responsible for damage caused by circumstances independent of the Manufacturer, including but not limited to floods, storms, fire, lightning, natural disasters, earthquakes, war, civil unrest and other force majeure, unfore seen accidents, or theft
Manufacturer:
Allterco Robotics EOOD
Address: Sofia, 1407, 103 Cherni vrah blvd.
Tel.: +359 2 988 7435
Email: support@shelly.cloud
http://www.Shelly.cloud
The Declaration of Conformity is available at:
https://Shelly.cloud/
declaration of conformity
Changes in the contact data are published by the Manufacturer at the official
website of the Device:
http://www.Shelly.cloud
The User is obliged to stay informed for any amendments of these warranty
terms before exercising his/her rights against the Manufacturer
All rights to trademarks She ® and Shelly ® and other intellectual rights
associated with this Device belong to Allterco
Robotics EOOD 2019/01/v01 You can find the latest version of the Shelly RGBW2
user guide on this address: https://shelly.cloud/downloads/ Or by scanning
this QR code:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>