Nikon 05420083 NIKKOR Z 50mm f or 1.8 S Standard Prime Lens User Manual

**Nikon 05420083 NIKKOR Z 50mm f or 1.8 S Standard Prime Lens User Manual

**

Before using this product. please carefully read both these instructions and the camera manual

Note:
This lens is intended exclusively for use with misrules cameras featuring a Nikon Z mount .

For Your Safety

To prevent damage to property or injury to yourself or to others, read “For Your Safety” in its entirety before using this product.

Keep these safety instructions where all those who use this product will read them.

WARNING: Failure to observe the precautions marked with thi s icon could result in death or severe injury.

CAUTION: Failure to observe the precautions marked with this icon could result in injury or property damage.

WARNING

• Do not disassemble or modify this product.
  Do  not touch internal parts that become exposed as the result of a fall or other accident.
  Failure to observe these precautions could result in electric shock or other injury

• Should you notice any abnormalities such as the product producing smoke, heat, or unusual odors, immediately disconnect the camera power source. Continued operation could result in fire, burns or other injury.

• Keep dry.
  Do not handle with wet hands.
  Failure to observe these precautions could result in fire or electric shock.

• Do not use this product in the presence of flammable dust or gas such as propane, gasoline or aerosols.
  Failure to observe this precaution could result in explosion or fire.

• Do not directly view the sun or other bright light source through the lens.
  Failure to observe this precaution could result in visual impairment.

• Keep this product out of reach of children.
  Failure to observe this precaution could result in injury or product malfunction. In addition, note that small parts constitute a choking hazard. Should a child swallow any part of this product, seek immediate medical attention.

• Do not handle with bare hands in locations exposed to extremely high or low temperatures.
  Failure to observe this precaution could result in burns or frostbite.

CAUTION

• Do not leave the lens pointed at the sun or other strong light sources. Light focused by the lens cou ld cause fire or damage to product’s internal parts. When shooting backlit subjects, keep the sun well out of the frame.

• Do not leave the product where it will be exposed to extremely high temperatures, for an extended period such as in an enclosed automobile or in direct sunlight.
  Failure to observe this precaution could result in fire or product malfunction.

• Do not transport cameras or lenses with tripods or similar accessories attached.
  Failure to observe this precaution could result in injury or product malfunction.

Notices for Customers in the U.S.A.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Federal Communications Commission (FCC) Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/television technician for help.

CAUTIONS

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Nikon Corporation may void the user’s authority to operate the equipment.
Nikon Inc., 1300 Walt Whitman Road,
Melville, New York 11747-3064, U.S.A
TeL 631-547-4200

Notice for Customers in Canada
manual CAN ICES-3 Bi NMB-3 B

Using the Lens

Parts of the Lens: Name and Function

Refer to the diagram on the left edge of this sheet.

rotate this customizable ring to perform a function selected with the camera (see the camera manual for details).| —
Manual focus mode selected: Rotate to focus.| —
3 Lens mounting mark| Use when mounting the lens on the camera.| see A
4 Rubber lens-mount v-1-1 gasket| __|
5 CPU contacts| Used to transfer data to and from the camera.| —
6 Focus-mode switch| Choose A for autofocus, M for manual focus. Note that regardless of the setting chosen, focus must be adjusted manually when manual focus mode is selected using camera controls.|
7 Lens hood| Lens hoods block stray light that would otherwise cause flare or ghosting. They also serve to protect the lens.| See B
8 Lens hood lock mark| See B Use when attaching the lens hood.
9  Lens hood alignment w mark
10 Front lens cap| —| –
11 Rear lens cap| —| —

Attachment and Removal

Attaching the lens

1. Turn the camera off, remove the body cap, and detach the rear lens cap
2. Position the lens on the camera body, keeping the mounting mark on the lens aligned with the mounting mark on the camera body, and then rotate the lens counterclockwise until it clicks into place.

Removing the Lens

1. Turn the camera off.
2. Press and hold the lens release button while turning the lens clockwise.

Attaching and Removing the Lens Hood

Align the lens hood mounting mark ( ) with the lens hood alignment mark ( ) and then rotate the hood ( ) until the  mark is aligned with the lens hood lock mark ( ).

**To remove the hood, reverse the above steps.

**

When attaching or removing the hood, hold it near the symbol on its base and avoid gripping it too tightly. The hood can be reversed and mounted on the lens when not in use.

When the Lens Is Attached

The focus position may change if you turn the camera off and then on again after focusing. Refocus before shooting. If you have focused on a pre-selected location while waiting for your subject to appear, we recommend that you do not turn the camera off until the picture is taken.

Precautions for Use

• Do not pick up or hold the lens or camera using only the lens hood.
• Keep the CPU contacts clean.
• Should the rubber lens-mount gasket be damaged, cease use immediately and take the lens to a Nikon-authorized service center for repair.
• Replace the front and rear lens caps when the lens is not in use.
• To protect the interior of the lens, store it out of direct sunlight.
• Keep the lens dry. Rusting of the internal mechanism can cause irreparable damage.
• Leaving the lens in extremely hot locations could damage or warp parts made from reinforced plastic
• Rapid changes in temperature may cause damaging condensation inside and outside the lens. Before ta king the lens from a warm toa cold environment or vice versa, place it in its case or a plastic bag to slow the change in temperature.
• We recommend that you place the lens in its case to protect it from scratches during transport.
• Do not pick up or hold the lens or camera using only the lens hood.
• Keep the CPU contacts clean.
• Should the rubber lens-mount gasket be damaged, cease use immediately and take the lens to a Nikon-authorized service center for repair.
• Replace the front and rear lens caps when the lens is not in use
• To protect the interior of the lens, store it out of direct sunlight.
• Keep the lens dry. Rusting of the internal mechanism can cause irreparable damage.
• Leaving the lens in extremely hot locations could damage or warp parts made from reinforced plastic.
• Rapid changes in temperature may cause damaging condensation inside and outside the lens. Before taking the lens from a warm toa cold environment or vice versa, place it in its case or a plastic bag to slow the change in temperature.
• We recommend that you place the lens in its case to protect it from scratches during transport.

Lens Care

• Removing dust is normally sufficient to clean the glass surfaces of the lens
• Smudges and fingerprints can be removed from the lens surface using a soft, clean cotton cloth or lens cleaning tissue lightly dampened with a small amount of ethanol or lens cleaner. Wipe gently from the center outwards in a circular motion, taking ca re not to leave smears or touch the lens with your fingers.
• Never use organic solvents such as paint thinner or benzene to clean the lens
• Neutral Color (NC) filters (available separately) and the like can be used to protect the front lens element.
• If the lens will not be used for an extended period, store it in a cool, dry location to prevent mold and rust. Do not store in direct sunlight or with naphtha or camphor moth balls.

Accessories

Supplied Accessories

• LC-62862 mm snap-on Front Lens Cap
• LF-Nl Rear Lens cap
• HB-90 Bayonet Hood
• CL-Cl Lens Case

Using the lens Case

• The case is intended to protect the lens from scratches, not from fall soro the physical shocks.
• The case is no water resistant
• The material use din the case may fade, shrink, or change color wean rubbed Dorset.
• Remove dust with a soft brush
• Water and stains can be removed from the surface with a soft dry cloth .Do not use alcohol, benzene, thinner, or other volatile solvent Soar detergents.
• Do not store in local i on sex posed to dire sunlight or high temperature soar humidity.
• Do not use the case to clean the monitor or lens elements.
• Be careful that the lens does not fall from the case during transport

Material: Polyester.

Compatible Accessories

62 mm screw-on filters

Filters
Use only one liter at a time. Remove the lenshoodbeforeattachingliltersorrotalingcircularpolariZinglilters

Specifications

Maximum
aperture| f/1.8
Lens construction| 12 elements in 9 groups (including 2 ED elements, 2 aspherical elements, and elements with Nano Crystal Coat)
Angle of view|

• FX format: 47°
• DX format: 31°30′

Focusing system| Internal focusing system
Minimum focus distance| 0.4 m (1.32 ft)
Diaphragm blades| 9 (rounded diaphragm opening)
Aperture range| f/1.8 — 16
Filter-attachment size| 62 mm (P = 0.75 mm)
Dimensions| Approx. 76 mm maximum diameter x 86.5 mm (distance from camera lens mount flange)
Weight| Approx. 415 g (14.7oz)

Nikon reserves the right ro change the appearance, specif1cations, and performance of this product or any time and without prior notice.

Warranty

Retain this International Warranty with proof of purchase (bill of sale) for your records Nikon Cor~. LENS ONE YEAR WORLDWIDE LIMITED WARRANTY
(Excluding the Continental United States, Alaska, Hawaii, Puerto Rico, and U.S. Virgin Islands)

Welcome to the worldwide family of Nikon owners.

Your Nikon equipment has been manufactured to the highest quality standards by NIKON CORPORATION, Tokyo, Japan. This limited warranty entitles the original consumer purchaser to international warranty protection in accordance with these terms and conditions. It affords the original consumer purchaser warranty protection outside the Continental United States, Alaska, Hawaii, Puerto Rico and the U.S. Virgin Islands. Such warranty coverage is supplemental to and not in lieu of the United States
Nikon Inc. Lens One Year USA Limited Warranty which is received by the original consumer purchaser with the Nikon product. The Nikon product except for batteries is warranted by NIKON CORPORATION, Tokyo, Japan to be free from defects in materials or workmanship for a period of one (1)year from the date of purchase. To find an international Nikon Service Facility see: http://imaging.nikon.com/products/imaging/worldwide/index.htm. During this period any one of the international service facilities will service without charge any parts or assembly of parts found to be defective in materials or workmanship, subject to the following limitations and exclusions:

1. This warranty extends to the original consumer purchaser only and is not assignable or transferable.
2. This warranty shall not extend to any product which has been subject to misuse, alteration, abuse, negligence, accident or unauthorized repair or has had its serial number altered or removed.

The above warranty is expressly in lieu of all other warranties expressed or implied including but not limited to any implied warranty of merchantability or fitness for particular purpose, except to the extent prohibited by applicable law, in which event the duration of any implied warranty shall be limited to one (1) year from the date of purchase or such longer period as may be required by applicable law. Under no circumstances shall Nikon be liable for consequential, indirect, special, direct, exemplary, punitive or incidental damages arising out of or related to any breach of this warranty or any other claim regarding this product, including but not limited to, claims of negligence, strict liability or breach of contract.

Some jurisdictions, such as states or provinces, do not allow (a) limitations on how long an implied warranty lasts or (b) the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction.

In order to obtain international service, the original consumer purchaser should return the Nikon product, either in person or addressed to the Warranty Department of any authorized service facility listed on the above website, together with proof of purchase and proof of purchase date (bill of sale) and this warranty. The original consumer purchaser in returning this product must prepay all shipping and insurance costs to the service facility.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>