DS18 NXL-69 6X9 Inch Marine Grade Coaxial Speaker Owner’s Manual

Table of Contents

2-Way Coaxial Speaker for Marine & Motorsports.
Continuous Power Handling 125W RMS
Peak Music Power 375W MAX
Sensitivity: 92dB at 1W/1M
Nominal Impedance: 4 Ohm
IP65 Marine Grade Compliant Specifications, 100% UV Stable.
Motor Structure Use Y35 Ferrite Main Magnet and Reverse Neodymium Magnet.
Copper Ring on Motor structure for far-field performance.
Injection Molded Polypropylene Cone with UV Protection and Butyl (rubber) Surround.
Injection Molded composite ASA Grill with UV protection Coating
Integrated RGB LED Lighting
LED Controller with Smartphone App Available For Multi-Function RGB LED Lighting option (Sold Separately)

Be sure to carefully read and understand the instruction before attempting to install these Speakers.
For Safety, Disconnect the negative Battery Terminal from the Battery Prior to Beginning the installation Process.
For Easier Assembly, We Suggest you Run all Wires Prior to Mounting Speakers in Place.
Use High Quality Connectors for a Reliable installation and to Minimize Signal or Power Loss.
Be Careful not to Drill or Cut into Gas Tanks, Fuel Lines, Brake or Hydraulic Lines, Vacuum Lines or Electrical Wiring while installing. lf installing in a Boat, be Careful Not to Cut or Drill Through the Main Hull.
Never Run Wires Undeath the Vehicle. In order to provide the best Protection. Make Sure to Run Wires inside the Vehicle or Hull.
Avoid Running Wires Over or Through Sharp Edges. Use Rubber or Plastic Grommets to Protect any Wires Routed Through Metal, Specially the Firewall.

Determine where the Speakers will be mounted. Be sure that the Mounting Area is Deep and Wide Enough for the Speaker to Fit. PLEASE ONLY MOUNT ON A FLAT SURFACE.
Refer to the Specification Chart to Determine the Proper Diameter for the Hole you need to Cut.
Mark the Location for the Mounting Screws. Drill the Holes with a 1/8” bit.
Feed the Speaker wires through the cutout and Connect to the Speaker Terminals. Watch out for Proper Polarity when Connecting the Wires.
Fit Speaker and Mount into Place using 6 screws.
Tighten the Screws until the Speaker is Snug in Place.
LED CONNECTIONS: There are two options to choose from:

lf you have an LED Control Module (LED-BTC), Connect as shown in the Following diagram:
To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:
Green Color: “G” Fast Terminal Connect to Battery Negative
Red Color: “R’ Fast Terminal Connect to Battery Negative
Blue Color: “B” Fast Terminal Connect to Battery Negative
Purple Color: “R” And “B” Fast Terminal Connect to Battery Negative
Yellow Color: “R’ And “G’ Fast Terminal Connect to Battery Negative
Cyan Color: “B” And “G” Fast Terminal Connect to Battery Negative
While Color:”R’ And ‘B’ And “G’ Fast Terminal Connect to Battery Negative

DS18-NXL-69-6X-Inch-Marine-Grade-Coaxial-Speaker-02

UV Compliant ……………………………………………………………………Yes, 100% Stable
Marine Grade Type………………………………………………………………………………………………………. IP65
RGB LED ………………………………………………………………………………….. Yes, RGB integrated
Grill Type ………………………………………..Injection Molded Composite ASA with UV Protection coating
Sold as Pair ………………………………………………………………………………………………………………………Yes

Voice Coil Diameter ……………………………………………………………………….1.4″ / 35.5mm
VC Former Material ……………………………………………………………………………….. Kapton
Winding Material …………………………………………………………………………………………………………….. SV
Cone Material ……………………………………………… Injection Molded Polypropylene + UV Compliant
Surround Material /……………………………………………………….. Butyl (Rubber) /
Basket Material………. High Temp Injection Molded Composite with UV Protection coating
Magnet Material /……………………………………………………………….Ferrite (Y35) + Neodymium (N35)
Magnet Weight ……………………………………………………………………………………………………… 24 OZ + 0.75 OZ