Ekemp Technology P8 Data Processing Unit User Manual
- June 5, 2024
- Ekemp Technology
Table of Contents
Technology P8 Data Processing Unit
**User Manual
**
P8 DATA PROCESSING UNIT
User Manual
V1.0
Function Distribution
Setting UP P8
Power on and off
P8 Technical Specification
| CPU | – ARM Cortex A53 Octa Core 1.5-2.0Ghz |
|---|---|
| Operation System | – Android 11 |
– Firmware Over-The-Air (FOTA)
Memory| – Onboard storage: 16GB eMMC=
– RAM: 2GB LPDDR
– External SD Card slot supports Max.=128 GB
Multiple Connectivity| – Wi-Fi: 8.11a/b/g/n/ac 2.4Ghz 5GHz
– Bluetooth: 5.0 BR/EDR/LE (Compatible with Bluetooth 1.x, 2.x, 3.x & 4.0)
– 2G: B1/2100;B2/1900;B5/850;B8/900
– 3G: B1/B2/B4 B5/B8
– 4G LTE: B2 B4 B5 B7 B12 B17
– Dual SIM
GNSS| – GPS
-GLONASS
– Galileo
Touchscreen Display| – Size: 8-inch diagonal
– Resolution: 800×1280 Pixels
– Type: Capacitive multi-touch panel
Fingerprint Scanner| – Optical Sensor
– 500dpi
– Morpho CBM-E3
Camera| – Front Camera 5 Megapixel
– Rear Camera: 8 Megapixel, Autofocus with Flash LED
Interface| – USB-C port with USB-On-The-Go (USB-OTG) support.
– USB 2.0
– DC slot
Rechargeable Battery| – 3.8V/10,000 mAh Li-Ion battery
– MSDS and UN38.3 certified
Integrated Printer| – Thermal Printer
– Support 58mm width parper roll
Accessories| – 2 hand straps
– 1 Shoulder strap
– 5V/3A charger
MDM| – Mobile Device Management
Certification| – FCC
Safety Information
Please read, understand, and follow all safety information contained in these
instructions prior to the use of this device. Retain these instructions for
future reference. It is expected that all users be fully trained in the safe
operation of this P8 Terminal equipment.
Risk of explosion if the battery is replaced by an incorrect type.
Do not disassemble, modify or service this device; it contains no user-
serviceable parts.
Do not use if the device, battery, or USB power cord is damaged.
Do not use this device outdoors or in wet locations.
INPUT: AC 100 – 240V
OUTPUT: 5V 3A
Rated frequency50 – 60 Hz
FCC Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. This Product meets the government’s requirements for
exposure to radio waves. The guidelines are based on standards that were
developed by independent scientific organizations through periodic and
thorough evaluations of scientific studies. The standards include a
substantial safety margin designed to assure the safety of all persons
regardless of age or health.
The WLAN function for this device is restricted to indoor use only when
operating in the 5150 to 5350 MHz frequency range.
FCC RF Exposure Information and Statement the SAR limit of the USA (FCC) is1.6
W/kg averaged over one gram of this Device Data Processing Unit (FCC ID:
2A332-P8) has been tested against this SAR limit. SAR information on this can
be viewed online at http://www.fcc.gov/oet/ea/fccid/. Please use the device
FCC ID number for the search. This device was tested for typical operations
0mm from the body. To maintain compliance with FCC RF exposure requirements,
0mm separation distance should. maintained to the user’s bodies
NOTE : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
FCC ID: 2A332-P8
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>