Steelmate BOT251 Sensor pad User Manual
- June 5, 2024
- Steelmate
Table of Contents
Steelmate BOT251 Sensor pad
Brief look
How to use
- Put your baby on the car seat before ACC ON:Put the sensor pad under the car seat cushion
- Put the baby on the seat and click the seat belt safely
- Plug the display in ( Do not press SET button )
- How to use Stick on the inside of the driver’s driver’s seat belt slot
- ACCON
- Display turns on with green light, then “Bitt twice within 3 minutes
Put your baby on the car seat after ACC ON:
- Put the sensor pad under the car seat cushion
- Plug the display in (Do not press SET button)
- Stick on the inside of the driver’s seat belt slot
- ACCON
- Buckle the driver’s seat belt
- The display “Bi” once to indicate the seat belt is buckled
- Put the baby on the seat and click the seat belt safely
- Display will “Bi” twice immediately to enter working mode
Baby is left the car seat while driving:
- Baby is left the car seat (Stand or not sit on the pad)
- Display will “Bi” three times, the warning light will turn to red
- Put the baby back to the car seat (Sit on the pad)
- Display will back to normal status with green light
Baby is remained on the car seat after ACC OFF:
-
ACCOFF
-
Baby is remained on the car seat The display “Bi” once to indicate the seat belt is unbuckled Baby is remained on
the car seat -
The display will flashing in turn with red & green lights until baby left the car seat or the display is turn off.Unbuckle the driver’s seat belt
-
Baby is remained on the car seat after unbuckle the driver’s seat belt:The display will flashing in turn with red & green lights until baby left the car seat or the display is turn off.
Baby didn’t sit on the car seat within 15 minutes after ACC
ON:
- ACCON
- Display turns on with green light
- No baby on car seat in 15 minutes
- ACC OFF
- Display will turn off immediately
Baby didn’t sit on the car seat more than 15 minutes after ACC
ON:
Voice adjustment
When ACC ON, the system enter the voice mode. Hold the “SET” button for 3 seconds to enter the voice setting mode. The display will “Bi” twice to indicate it’s in mute mode, “Bi” once means in voice mode.
- Voice mode: Voice ON
- Mute mode: Voice OFF
Note:
- The baby is remained on the car seat after ACC OFF, display will still alarm when it’s in mute mode.
- The system is in voice mode when ACC ON every time
Low battery reminder
When ACC ON, and baby sit on the car seat.
If sensor pad in low battery status
ACC ON, and baby sit on the car seat, when the system detectsthe sensor pad is
in low battery status, the display will warning and yellow light flashing for
3 times, then the light will return to green, and the system will back to the
working mode.
If seat belt detection kit in low battery status
Buckle the seat belt, when the system detects seat belt detection kit is in
low battery status, the display will warning and yellow light flashing once,
then the light will return to green, and thesystem will back to the working
mode.
Note:
- If not replace the battery in time, the display will alarm every time when ACC ON or buckle the seat belt.
- If no baby sit on the car seat, the display will not alarm to remind that sensor pad is in low battery status.
Product programming
(Reminder: l11e sensor pad and the seat beft delection kit are pre-
programmed)
- ACC ON
- Display turns on with green light
- Press “SET” button for 5 times
- Display turn yellow and “Bi” once to enter programming mode
If sensor pad to be programmed
- Hold the sensor pad for 2 seconds
- The display will “Bi” twice with green light flashing, then enter the next programing.
If eat belt detection kit to be programmed
- Buckle the driver’s seat belt, then unbuckle it
- The display will “Bi” once with yellow light flashing, then enter the next programing
After all parts are programmed, hold “SET” button, Then the display will
warning to save and exit the programming mode.
Note:
- Only 2 sensor pads and 1 seat belt detection kit can be up to programmed.
- If there is no operation within 2 minutes, the system will exit the programming mode automatically.
Specifications
F&Q
- The display light not turn on
- Display damaged.
- ACC ON.
- Sensor pad not work
- Sensor pad battery is low, please change to new sensor pad.
- The display and sensor pad are not programmed
- Sensor belt detection kit not work
- The sensor belt detection kit battery is low, please change to new sensor belt detection kit.
- The display and sensor belt detection kit are not programmed.
- The seat belt buckles with inner wall thickness 7mm will affect the use of this part.
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, Pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution:
Any changes or modifications to this device not explicitly approved by the
manufacturer could void your authority to operate this equipment. This
equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance 0cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>