HMD global Oy TWS-222 Nokia Go Earbuds2 Pro User Guide

: June 5, 2024
: HMD global Oy

Table of Contents

HMD global Oy TWS-222 Nokia Go Earbuds2 Pro
What’s in the box
Product Overview
Pair and connect with Bluetooth
Additional controls
Product and safety information
Recycle
Declaration of conformity
FCC Notice to users
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HMD global Oy TWS-222 Nokia Go Earbuds2 Pro

What’s in the box

Charging case
Earbuds (L/R)
Ear tips (S/M/L)
USB Type-C cable
Quick Start Guide

Product Overview

Charging case:

Charging contacts (L)
Charging contacts (R)
Charging case button
Battery status LEDs
USB Type-C port
Eartip
Touch control
Microphone

Get started
Before using Nokia Go Earbuds? Pro, take off the film on the earbuds and place the earbuds back in the charging case. Then connect the USB Type-C cable to a power source to begin charging. Fully charge the earbuds and the charging case before the first use.

For optimal fit and audio performance, replace the ear tips with the size that best suits you.

Pair and connect with Bluetooth

Pairing with the device
Turning on and pairing: When you take the earbuds out from the charging case, the earbuds will turn on and pair with each other automatically. When they have successfully paired, the LED indicator light of the right earbud will flash blue and red alternately and the earbuds are ready to connect with your Bluetooth device. Connecting with your

Bluetooth device:
Turn on Bluetooth in your device and choose “Nokia TWS-222” from 8- the Bluetooth menu to connect. Nokia Ty222 During the connection process,the LED indicator light on the right earbud will flash blue and red alternately. The LED indicator lights of the earbuds will flash blue every 10 seconds when they are successfully connected via Bluetooth. o 1/10 secs After the initial pairing, the earbuds will automatically connect with your Bluetooth device whenever taken out of the charging case. The earbuds will automatically power off if there is no Bluetooth connection within 5 minutes.

Using your earbuds
Touch control

Additional controls

Use single earbud:
You can use either leftor right bud as a mono headset after initial pairing.
Reset to the original settings

Press and hold touch control for 7 seconds to turn off.
Press and hold both buds for 10 sec.
Earbuds LED will flash purple 3 times when earbuds are reseted. Low latency mode gaming & video mode) Press control button (L/R)
times to toggle between low latency mode> OFF.x

Product and safety information

Remote control functions may vary depending on the model of your device and application. Soundtrack instructions do not respond to iOS devices. Since devices with Bluetooth wireless technology communicate using radio waves, they do not need to be in direct line-of-sight. Bluetooth devices must, however, be within 10 meters (33 feet) of each other, although the connection may be subject to interference from obstructions such as walls or from other electronic devices. Frequency Band: 2400 MHz – 2480 MHz
Maximum Radio Frequency Power: -6~+4dBm

For your safety
Important: Read these simple guidelines. Not following them may be dangerous or against local laws and regulations. For further info, read the complete user guide. Switch off in restricted areas Switch the device off when a Bluetooth headset use is not allowed or when it may cause interference or danger, for example, in aircraft, in hospitals or near medical equipment, fuel, chemicals, or blasting areas. Obey all instructions in restricted areas.

Interference
All wireless devices may be susceptible to interference, which could affect performance.

Batteries, chargers, and other accessories
Use only batteries, chargers, and other accessories approved by HMD Global Oy for use with this device. Do not connect incompatible products.

Protect your hearing
To prevent possible hearing damage, do not listen at high volume levels for long periods.

Hearing
Warning: When you use the headset, your ability to hear outside sounds may be affected. Do not use the headset where it can endanger your safety.

Small Small children
Your device and its accessories are not toys. They may contain small parts. Keep them out of the reach of small children.

Take care of your device
Handle your device with care. The following suggestions help you keep your device operational Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that corrode electronic circuits.

Do not use or store the device in dusty or dirty areas.
Do not store the device in high temperatures. High temperatures may damage the device or battery.
Do not store the device in cold temperatures. When the device warms to its normal temperature, moisture can form inside the device and damage it.
Do not open the device other than as instructed in the user guide.
Do not drop, knock, or shake the device or the battery. Rough handling can break it. Only use a soft, clean, dry cloth to clean the surface of the device.
Do not paint the device. Paint can prevent proper operation.

Recycle

Always return your used electronic products, batteries and packaging materials to dedicated collection points. This way you help prevent uncontroled waste disposal and promote the recycling of materials. Electrical and electronic products contain a lot of valuable materials, including metals (such as copper, aluminium, steel, and magnesium) and precious metals (such as gold, silver, and palladium). All materials of the device can be recovered as materials and energy.

Crossed-out wheelie bin symbol
The crossed-out wheelie bin symbol on your product, battery, literature, or packaging reminds you that all electrical and electronic products and batteries must be taken to separate collection at the end of their working life. Do not dispose of these products as unsorted municipal vwaste: take them for recycling. For info on your nearest recycling point, check with your local waste authority.

Battery info
your device has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery, as you may damage the device. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Charging time can vary depending on device capability.

Battery safety
If left unused, a fully charged battery willose its charge over time. Always keep the battery between 15°C and 25°C (59°F and 77°F) for optimal performance. Extreme temperatures reduce the capacity and lifetime of the battery. A device may temporarily stop working if its battery is too hot or too cold. Do not dispose of batteries in a fire as they may explode. Obey local regulations. Recycle when possible. Do not dispose as household waste. Use the battery and charger for their intended purposes only. Improper use, or use of unapproved or incompatible batteries or chargers may present a risk of fire, explosion, or other hazard, and may invalidate any approval or warranty. If you believe the battery or charger is damaged, take it to a service centre or your local shop before continuing to use it. Never use a damaged battery or charger. Only use the charger indoors. Do not charge your device during a lightning storm.

Implanted medical devices
To avoid potential interference, manufactures of implanted medical devices recommend a minimum separation of 15.3 centimetres (6 inches) between a wireless device and the implanted medical device. Persons who have such devices shoukd:

Always keep the wireless device more than 15.3 centimetres (6 inches) from the medical device.
Not carry the wireless devise in a breast pocket.
Switch the wireless device off if there is any reason to suspect that interference is taking place.
Follow the manufacturer’s directions for the implanted medical device.
If you have any questions about using your wireless device with an implanted medical device, consult your health care provider.

Copyrights and other notices
The availability of products, features, apps, and services may vary by region. For more info, contact your dealer or your service provider. This device may contain commodities, technology or software subject to export laws and regulations from the US and other countries. Diversion contrary to law is prohibited. The contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or contents of this document. HMD Global reserves the right to revise this document or withdraw it at any time without prior notice. Reproduction, transfer or distribution of part or all of the contents in this document in any form without the prior written permission of HMD Gdobal is prohibited. HMD Gobal operates a policy of continuous development. HMD Global reserves the right to make changes and improvements to any of the products described in this document without prior notice. Manufacturer and importer in EU: HMD Global Oy, Bertel Jungin aukio 9, 02600 Espoo, Finland. HMD Global Privacy Policy, available at http://www.nokia.com/phones/privacy, applies to your use of the device. In the unlikely event that this product is faulty, please return it to the store where you purchased it with your proof of purchase. For more information on this or other products please visit http://www.nokia.com/phones/support. 2022 HMD Global. All rights reserved. HMD Global Oy is the exclusive licensee of the Nokia brand for phones&tablets. Nokia is a registered trademark of Nokia Corporation. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by HMD Global is under license.

Declaration of conformity

Hereby, HMD Global Oy dedares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. A copy of the
Declaration of Conformity can be found at: www.nokia.com/mobile-declaration-of-conformity.

FCC Notice to users

The following statement applies to all products that bear the FCC logo and/or FCC ID on the product label This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. See 47 CFR Sec. 15.105(b). These limits are designed to provide reasonable protection against harmful interference ina residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wil not occur in a particular instalation. If this equipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules.

Industry Canada Notice to users
This device contains license-exempt transmitter(s)/receiver (s) that comply with Innovation, Science and Economic Development Canada licensed-exempt RSS(s). Operation is subject to the following two conditions: