BOSS BC-1XBC-1X Bass Compressor Pedal Owner’s Manual

BC-1XBC-1X Bass Compressor Pedal
Owner’s Manual

BC-1XBC-1X Bass Compressor Pedal

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.

Main Features

• This is a dedicated compressor for bass that uses Boss’s cutting-edge MDP digital technology to make your sound consistent without impairing the fundamental frequency of your instrument.
• A gain reduction indicator is provided so that you can see the results of compression.
• The internal operating voltage of 18 V means that you can confidently connect even high-output basses to this unit, which is designed specifically for bass input.
• An internal voltage boost circuit is used to provide 18 V operation.

Panel Descriptions

Precautions When Connecting

• To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units before making any connections.

• Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices.
  When powering up: Turn on the power to your bass amp last.
  When powering down: Turn off the power to your bass amp first.

• Immediately after the unit is powered-on, the effect is on.

Use of Battery

• A battery was installed in the unit before it left the factory. The life of this battery may be limited, however, since its primary purpose was to enable testing.
• If you handle batteries improperly, you risk explosion and fluid leakage. Make sure that you carefully observe all of the items related to batteries that are listed in “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
• When operating on battery power only, the unit’s indicator will become dim when battery power gets too low. Replace the battery as soon as possible.
• Batteries should always be installed or replaced before connecting any other devices. This way, you can prevent malfunction and damage.
• The use of an AC adaptor is recommended as the unit’s power consumption is relatively high. Should you prefer to use batteries, please use the alkaline type.

Changing the Battery

1. Hold down the pedal and loosen the thumbscrew, then open the pedal upward.

• The pedal can be opened without detaching the thumbscrew completely. 2. Remove the old battery from the battery housing, and remove the snap cord connected to it. 3. Connect the snap cord to the new battery, and place the battery inside the battery housing.
• Be sure to carefully observe the battery’s polarity (+ versus -). 4. Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal.
• Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing. 5. Finally, insert the thumbscrew into the guide bush hole and fasten it securely.

Specifications

AC adaptor (PSA series: sold separately)
Current Draw| 90 mA

• Expected battery life under continuous use:
  Alkaline: 2 hours
  These figures will vary depending on the actual conditions of use.
  Dimensions| 73 (W) x 129 (D) x 59 (H) mm
  2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
  Weight| 440 g / 1 lb (including battery)
  Accessories| Leaflet (“USING THE UNIT SAFELY,” “IMPORTANT NOTES,” and “Information”) Alkaline battery (9 V, 6LR61)
  Options (sold separately)| AC adaptor (PSA-series)

0 dBu = 0.775 Vrms
This document explains the specifications of the product at the time that the document was issued. For the latest information, refer to the Roland website.

© 2016 Roland Corporation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>