DS18 CF-X6TP.NS Marine Tower Pod for 6.5 Inch Speakers Owner’s Manual

June 5, 2024
DS18

OWNER’S MANUAL
CF-X6TP.NS

MARINE TOWER POD FOR 6.5″ SPEAKERS
WITH GRILL, RGB LED LIGHTS AND CARBON FIBER TEXTUREDS18 CF X6TP NS
Marine Tower Pod for 6 5 Inch Speakers

FEATURES

FEATURES

  • Pair of empty enclosures to use with your favorite DS18 6.5” Speaker
  • IP65 Marine Grade Compliant Specifications, 100% UV Stable
  • Grill with Injection Molded Composite with 316 Stainless Steel mesh
  • Integrated RGB LED Lighting
  • LED Controller with Smartphone App (LED-BTC) Available For Multi-Function RGB LED Lighting option (Sold Separately)

PACKAGING INCLUDES

  • (2) CF-X6TP.NS Marine Towers
  • (2) Mounting clamps (Pre-Installed on speakers)
  • (4) M6 x 15mm bolts (Pre-Installed)
  • (6) Rubber clamp adapters (1/8” thickness)

INSTALLATION

READ BEFORE INSTALLATION

  1. Be sure to carefully read and understand the instructions before attempting to install these speakers.
  2. For safety, disconnect the negative battery terminal from the battery prior to beginning the installation.
  3. For easier assembly, we suggest you have all your tools in hand- Drill, Allen set, Crimp, Soldering iron, Wire Strippers, Heat-shrink, etc.
  4. Use high-quality “Waterproof’ connectors for a reliable installation and to minimize signal or power loss.
  5. Think before you drill! Be careful not to cut or drill into gas tank, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle. If installing in a boat, make sure not cut or drill through the main hull.
  6. Never run wires near fuel lines or power (if possible). Running the wires inside the hull or car area provides the best protection.
  7. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the tower.
  8. Make sure that the mounting clamp or “L” bracket are tight before leaving the dock.
  9. Decide early what type of LED lighting you want (if any) and wire accordingly

(NOTE: if you want “Dancing Light” look to the WiFi or RF or BT remote- controlled LED light box. The easy way to have lighting … YOUR way!)

INSTALLATION EQUIPMENT

  • An Electric Drill With Bits
  • Allen / Hex Key / Wrench Set
  • Philips Head And Standard Screw Drivers
  • Wire Strippers
  • Crimping Tool
  • Vom (Electronic Volt Ohm Meter)
  • Heat Shrink Tubing And Heat Gun
  • Soldering Iron
  • Electronic (Rosen Not Acid Core) solder

BEGINNING MOUNTING
Step 1: Install your preferred speaker on the tower by connecting the speaker cables inside and then securing it with the supplied mesh and screws.
Step 2: Find a GOOD location that allows for easy wiring of the speaker (and LED lights) -PLUS does NOT impair your movement around the location.
Step 3: Using the supplied 6mm hex wrench spin out the 4-M8 screw that holds the top clamp
Step 4: Drill 015 – 020 mm hole on the mounting tube bottom align the clamp wire out hole.
Step 5: Connect the speaker wire AMP out and LED controller, Insulated lock the clamp to the tube.
Step 6: Cut the length of the rubber pad and wires outlet according to the diameter of the installation pipe.

DS18 CF X6TP NS Marine Tower Pod for 6 5 Inch Speakers -
fig

Step 7:Wrap the rubber pad around the pipe and align the wire out the hole According to the diagram. DS18 CF X6TP NS Marine Tower Pod for 6 5 Inch
Speakers - fig 1

Step 8: Push the wire into the tube, press on the rubber pad, and lock the top clamp.
Step 9: Take down the safety rope and hang it on the pipe, lock the screw gasket safety rope lifting ring on the clamp base, and apply screw fastening glue on the screw before
locking.
Step 10: If need be, rotate the speakers for best dispersion, this is easily done by locating the 6mm & 4mm hex wrench set screw on the side of the clamp base, rotating the speaker/enclosure to the desired angle, once there… locking the screws tight. Avoid vibration, clamp loose!!!

Step 11: During the mounting process, you should have located the spot to drill your tower bar for the 6 conductor wire (Speaker and RGB lightning wiring) insertion. Or NOT
(see Tie-wrap solution below)
Step 12: Remove Wire NBR Plug and Slide the wire through the hole Snake the wire down to the bottom of the tower tube in a location that the wires can be attached to the audio (And lighting) system. Solder or butt connects the speaker wire coming from the tower to the speaker wire to the system. Then heat-shrink it for added protection from water/moisture.

DS18 CF X6TP NS Marine Tower Pod for 6 5 Inch Speakers -
fig3| DS18 CF X6TP NS Marine Tower Pod
for 6 5 Inch Speakers - fig4
---|---

Step 13: When you want to install a flat mounting, remove the clamp and take out the 6 core through it into the flat mounting bracket, then assemble it, see depiction below.

WIRING

INSTALLATION & CONNECTION OPTIONS
If you have an LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:DS18 CF X6TP NS Marine Tower Pod for 6 5 Inch Speakers -
fig6

To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:

  • Black wire”BK” connected to battery Positive (+) 12V
  • White Color Light “R”; “B” and “G” connected to battery Negative (-)
  • Green Color Light “G” connected to battery Negative (-)
  • Red Color Light “R” connected to battery Negative (-)
  • Blue Color Light “B” connected to battery Negative (-)
  • Purple Color Light “R” and “B” connected to battery Negative (-)
  • Yellow Color Light”R” and “G” connected to battery Negative (-)
  • Cyan Color Light “B” and “G” connected to battery Negative (-)

DS18 CF X6TP NS Marine Tower Pod for 6 5 Inch Speakers -
fig7

SPECIFICATIONS

BODY FEATURES

Nominal Diameter …………………… 6.5″ / 165mm
Marine Grade ………………………………………………………………….. IP65
UV Compliant …………………. Yes, 100% Stable / Si, 100% Estable
RGB LED / LED RGB ….. Integrated LED-RGB Speaker Lighting, Integrated LED-RGB Acrylic Ring Lighting
LED-RGB integrada
Wiring……… 6 Core Wires for Lighting and Speaker
Enclosure Material ……………..Injection PC+ABS / Injection PC+ABS
Grill Material ……………. Injection Molded Composite with 316 Metal mesh
Clamp………………………… Die-Cast Adjustable (1″~2″) 360 Degree
Rotation Mounting Buried Wire or Open Wire Mounting Optional, Included NBR Pad And Stainless Hardware
(Screws, Stop Washers, Hexagon wrench, Safety Rope, Screw fastening Glue)
Enclosure Material ……….Injection PC+ABS / Injection PC+ABS
Front Logo …………………….. Yes, can be rotated for correct angle display
Rear Logo ………………………. Yes, can be rotated for correct angle display
Sold as Pair…………………………………………………………………………. Yes / Si
Color & Finish ……. Glossy Carbon Fiber Texture
TOWER MEASUREMENT
Overall Diameter ………………………………………………. 6.93″ / 176.1mm
Overall Depth ………………………………………………………… 11.42″ / 290.2mm
Overall Height (with clamp) ………………..10.7″ / 271.7mm
SPEAKER MEASUREMENT
Mounting Hole Diameter ……………………. 5.3″ / 135mm
Overall Diameter ……………………………………………………… 6.93″ / 176.1mm

MEASUREMENT

DS18 CF X6TP NS Marine Tower Pod for 6 5 Inch Speakers -
fig8| DS18 CF X6TP NS Marine Tower Pod
for 6 5 Inch Speakers - fig9
---|---

WARRANTY

Please visit our website DS18.com for more information on our warranty policy.

FOR MORE INFORMATION PLEASE VISITDS18.COM 
WE LIKE IT LOUD

Documents / Resources

| DS18 CF-X6TP.NS Marine Tower Pod for 6.5 Inch Speakers [pdf] Owner's Manual
CF-X6TP.NS, Marine Tower Pod for 6.5 Inch Speakers, CF-X6TP.NS Marine Tower Pod for 6.5 Inch Speakers, Tower Pod for 6.5 Inch Speakers, Pod for 6.5 Inch Speakers, Speakers
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DS18 User Manuals

Related Manuals