IP-INTEGRA FREUND Audio Client Software User Manual
- June 5, 2024
- IP-INTEGRA
Table of Contents
IP-INTEGRA FREUND Audio Client Software
Product Setup
Upon extracting the device from the package, plug in the network cable into RJ
45 ethernet port. After device has turned on, it will be scannable by IP-
INTEGRA SIP server (See Provisioning Devices section of a FE-INT-SIP(D) User
Manual) where you can see an IP address that the device has received. Default
network setting is DHCP.
To access the web interface, a PC is required, and it must be connected to the
same network as SIP server and SIP Audio device. Using the web browser, access
the web interface by entering the IP address of a device into the address bar.
NOTE: If device “Host” name is shown on the list, it means that IP-Client is not licensed.
Log in and Homepage
The IP address for FREUND AUDIO server is given by the DHCP. Upon accessing
the web interface, user will be prompted to enter a username and password.
Default values are “admin” for both fields.
After clicking the Submit button, the Homepage will open.
Homepage
Upon reaching the Homepage page, on the left side user will see a Navigation
panel containing following sections: Tools, Settings, Logs, and System. On the
right side is the Dashboard that provides overview of the whole environment.
This includes System Status, SIP Status, Information, Event Logs, and
shortcuts to following pages: Accounts, Scheduler, Sounds and Network
Settings.
Language can be changed in the top-right corner of the page. Available
languages are English and Danish.
Menu
Tools
Under tools section you can find Dashboard, Accounts, Scheduler and Sounds.
Dashboard
Dashboard is the default part of the Homepage. Under the SIP status, within
the Dashboard, is the option Remote support. It is disabled by default. To
enable it, users need to simply click on the ‘Disabled’ button and the prompt
for enabling it will show.
Remote support will stay enabled until user manually disables it.
Accounts
Accounts section within Tools allows users to link a device to an extension in
SIP server. Prerequisite for this is created extension on SIP server, which
gives us extension number and secret (Password is called Secret in SIP
server). This is thoroughly described in SIP Server User Manual.
To set up the device with SIP server, Username, Password, Host and Port fields need to be filled in as well as Enabled button must be ticked.
- Username – Assigned extension number in SIP server is entered under Username field on the device interface.
- Password – Under Password field, we will enter the Secret that can be found under Extension settings in SIP server.
- Host – IP Address of a SIP server.
- Port – Port over which the communication to SIP server is established.
Also, a list of codecs is displayed which user can tune to suit his needs.
Scheduler
Scheduler allows creation of multiple schedule times for extension or ring
groups or even transferring scheduler configuration from SIP server. In
Actions tab, scheduled events with eye icon are transferred from SIP server.
Their configuration can only be seen by user.
When creating a new event, users need to name it and give it at least starting
date. Expiry date is optional. Also, users can select which days in a week
will the scheduler work.
Clicking on Add Ring Time creates an alarm. User has ability to select time.
Bulk Add allows creating multiple alarm times by entering time, number of
rings, and period between rings. Users can select one of the pre-existing
sounds or upload their own (check 5.1.4 Sounds section of this document) to be
played on alarm time. 
Sounds
Sounds section allows uploading audio files which can be played and used in a
scheduler. 
Settings
Under Settings section, user is able to adjust Network Settings, Date and Time Settings, and System Settings.
Network Settings
Under Network Settings, user can adjust IP Address, Netmask, Gateway, and DNS
of a SIP audio device. Default settings are shown in the picture below. 
Date and Time Settings
Here, users are able to adjust date and time as well as designate a time zone.
Network Time Protocol (NTP) is a networking protocol for clock synchronization
between computer systems over packet-switched, variable-latency data networks.
NTP is intended to synchronize all participating computers to within a few
milliseconds of Coordinated Universal Time (UTC).
System Settings
Here, users are able to configure the Sound, Voice and Microphone volume by moving sliders left or right, and Microphone boost should they need it.
- Options for Echo cancellation are located right below the volume sliders.
- Alarm Sound File option allows uploading of a custom alarm sound.
- Mute – mutes the audio input
- No audio capture – disables audio input (same functionality as Mute, but sends no data)
- Silence Suppression when enabled, prevents device from transmitting information over network that is under the level of Silence Threshold.
- Silence Threshold allows user to designate what sound levels are classified as Silence; and shall not be transmitted.
- Sync Server IP is the IP address of a SIP server that device is synchronized to.
- Sync Interval is the amount of time that passes between device checking for changes on SIP server.
- Dial Extension – Upon pressing the button, the device will dial the entered extension number (Only for SMOD and DMOD)
- Paging Start Sound if enabled will make a sound upon paging.
- Paging Stop Sound if enabled will make a sound when paging has stopped.
- Play On Button – Enable or Disable sound file reproduction upon button press*.
- Randomly Play On Button – Play a random audio file (If there are files selected).
- Select Button to Play On – Decide which button will reproduce a sound file (If more than one button exists on a device).
- Files To Play On – Select files to be reproduced.
Users are also able to select a Paging Start Sound on this page.
*Available only on FREUND speaker with built-in buttons or audio device with a button switch. 
Logs
Logs section contains lists of all Call Logs, Event Logs and Scheduler Logs.
System
Under System section users have option to perform an Update, Reboot or Factory Reset the device or power it off by clicking on the Shut Down button.
Freund Elektronik A/S, in cooperation with our sister company Freund
Elektronika D.O.O.
Sarajevo, is developing an IP-Based Intercoms, Audio Systems, Access Control
and Smart
Home solutions.
As a developer, manufacturer, and reseller, we have been self-improving and
perfecting
ourselves for over 30 years.
In the industry, we negotiate the most advanced and innovative solutions
regarding the
building communication. Our daily focus is on the development and user
friendliness of our high quality and pleasantly designed products.
As a developer and manufacturer of our own IP-INTEGRA system, we have made a
top-of-the-line products for Door Telephony, Public Audio, and Access Control
solution.
Our development department, together with our partners, has created elegant
and robust door phones, SIP-Centrals, Terminals, IP-Speakers, ACC Controllers,
and applications with
intelligent features using the most advanced technologies when available, and
creating new
technologies when they are not while keeping it simple for our customers.
FREUND ELEKTRONIKA d.o.o
International Burch University | Francuske revolucije bb | 71210 Ilidza |
Bosnia and Herzegovina www.ip-integra.com | info
@ip-integra.com | +387 33 922 890