COOKOLOGY ELITE905BK 90cm Black Angled Designer Chimney Cooker Hood and Filters Instruction Manual

ELITE905BK 90cm Black Angled Designer
Chimney Cooker Hood and Filters
Instruction Manual

Notice

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if  they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.  Cleaning and user maintenance shall not be made by children without supervision
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
The instructions shall state the substance of the following:

• there shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only  discharge the air back into the room);

• the details concerning the method and frequency of cleaning;

• there is a fire risk if cleaning is not carried out in accordance with the instructions;

• do not flambé under the range hood;

• CAUTION: Accessible parts may become hot when used with cooking appliances.
  The installation instructions shall include the substance of the following:

• the air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the  air back into the room);

• the minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood. (When the range hood is located above a gas appliance, this distance shall be at least 65 cm.

• regulations concerning the discharge of air have to be fulfilled.

The installation instructions for range hoods with accessible metallic enclosures of class II construction shall include details that indicate the location and maximum permitted lengths for any fixing or mounting screw or another fixing device that penetrates into the range hood to attach an accessory such as a facia or duct fitting.
Where fixing or mounting screws, or other fixing devices are used, that penetrate into the range hood with an accessible metallic enclosure of class II construction, to attach an accessory, the instructions shall indicate the required location of these screws or fixing devices and include the substance of the following warning.
Warning: Failure to install the screws or fix the device in accordance with these instructions may result in electrical hazards

Feature

1. The cooker hood uses high-quality materials and is made with a streamlined design.
2. Equipped with a large power low noise electric motor and centrifugal leaf, it produces strong suction, low noise, nonstick grease filter, and is easy to clean.
3. In special wind tunnel construction and oil collector design, free dirt will be absorbed in a second.

IMPORTANT: IDEALLY YOU SHOULD SWITCH ON YOUR HOOD TEN MINUTES BEFORE YOU START TO COOK, OR AT THE VERY LEAST WHEN  YOU BEGIN COOKING. YOU SHOULD ALSO RUN YOUR HOOD FOR TEN MINUTES AFTER YOU HAVE FINISHED COOKING.

Notice of installation

1. Before installation, please ensure the area is clean to avoid the suction of the remaining bits of broken wood and dust.
2. It cannot share the same air ventilation tube with other appliances such as gas tubes, warmer tubes, and hot wind tubes.
3. The bending of the ventilation tube should be≥120°, parallel or above the start point, and should be connected to the external wall.
4. After installation, make sure that the extractor is level to avoid
5. grease collection at one end.

Installation

MOUNTING OF THE V-FLAP
If the cooker hood does not have an assembled V-flap 1, you should mount the half-parts to its body. The images only show an example of how to mount the V-flap, the outlet may be varied according to different models and configurations.
To mount the V-flap 1 you should:

• Mount two half-parts 2 into the body 6
• a pin 3 should be top-oriented;
• axis 4 should be inserted in holes 5 on the body;
• repeat all the operations for the 2nd half-part
  

If you have an outlet to the outside, your cooker hood can be connected as in below picture by means of an extraction duct (enamel, aluminum, flexible pipe, or non-flammable  material with an interior diameter of 150mm)

1. Before installation, turn the unit off and unplug it from the outlet.

2. The cooker hood should be placed at a distance of 65~75cm above the cooking surface for best effect.

3. Drill 4pcs φ8 mm holes in the wall at a suitable place to fix inside chimney bracket and hood body once the installation height is fixed, and keep it in line. The installation position of the inside chimney bracket is the highest position of the inside chimney. see Pic 2.

4. Insert wall plugs into the holes that you have drilled for the cooker hood body, fasten the hood body with 2 × support screw ST430 mm halfway in, leaving them 2 mm out of the wall, then use 2pcs ST440mm screws to fix the inside chimney bracket. See Pic 2.

5. Install the expansion pipe onto the cooker hood by screws, see Pic 3.
   

6. Install the outside chimney bracket on the outside chimney, and make sure that the inside chimney could be moved inside, see Pic 4.

7. Hang the hood on the screw, adjust the cooker hood position, and fix the cooker hood with ST4*30mm screws (safety screws). See Pic 5.
   

8. Adjust the height of the inside chimney to the position of the inside chimney bracket and fix it with screws. See Pic 6.
   Note: The two safety vents are positioned on the back housing, with a diameter of 6mm.

SPEED ADJUSTMENT

Touch control with LED display

1. Press the “Power” button, the button controls the “on” & “off ” of the hood.
2. Press the button “Speed” time after time, and the motor runs as low /mid/high/low/mid…, the speed runs circularly, and the LED display will indicate as 1-2-3-1-2…  circularly.
3. Press the “Light” button, and the light is on, press this button again, and the light is off. Please note the Lamp is not under the control of the on/off button.
4. When the hood is working, if press the “Timer” button, the hood will go into the status of acquiescent working (acquiescent time is 9mins), and then, the LED display will be shown 9.8.7.6 …decreasing by 1, when time is up, the hood will be off automatically and the lamp will extinguish. If pressing the “Timer” button, the hood will go in or go out of the “Timer” function.

Safety Warning

In certain circumstances, electrical appliances may be a danger hazard.

• Keep electrical appliances out of reach of Children or infirm persons. Do not let them use the appliances without supervision.
• This appliance is not intended for use by persons (including children) with the reduced physical. Sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Do not touch the light bulbs when/after appliance use.
• Do not check the status of the filters while the cooker hood is operating
• Flame cooking is prohibited underneath the cooker hood
• Your cooker hood is for domestic use only, not suitable for barbecue, roast shop and other commercial use.
• Any installation work must be carried out by a qualified electrician or competent person.
• Before cleaning, always ensure that you have switched your cooker hood off.
• Clean the cooker hood according to the instruction manual and keep the cooker hood from the danger of burning.
• No fire for drying your cooker hood.
• If there is any fault with your cooker hood, please call the service department appointed by an agent for servicing.
• If the power cord is damaged, it must be replaced by the manufacturer or a qualified service engineer in order to avoid a hazard.
• Do not exhaust the gas from the cooker hood through the same heated flue which is for the gas from the gas hob and other kitchen appliances.
• Before installation and usage, read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on your cooker hood are exactly the same as the voltage (V) and the frequency (Hz) in your home.
• Regulations concerning the discharge of air have to be fulfilled.
• CAUTION: Accessible parts may become hot when used with cooking appliances.
• Attention! Observe the warning in the instruction sheet concerning the operation of the appliance when air is discharged from the room.

MAINTENANCE

1. It is recommended to operate the appliance prior to cooking.
2. It is recommended to leave the appliance in operation for 15 minutes after cooking is terminated in order to completely eliminate cooking vapors and odors.
3. The proper function of the cooker hood is conditioned by the regularity of the maintenance operations, in particular, the active carbon filter.
4. The anti-grease filters capture the grease particles suspended in the air, and are therefore subject to clogging according to the frequency of the use of the appliance.
5. The cooker hood must be regularly cleaned on both the inside and outside with hot water plus non-corrosive detergent (AT LEAST ONCE A MONTH) to protect the main body from corrosion over a long period of time.
   

Attention! Please do not use abrasive detergent or alcohol as it will damage the body.
Attention! Keep the motor and other spare parts free from water, as this will cause damage to the appliance.
Attention! Before cleaning the appliance please remember to cut off the power.

CARBON FILTER-not supplied
An activated carbon filter can be used to trap odors. Normally the activated carbon filter should be changed at three or six months according to your cooking habit. The installation procedure of the activated carbon filter is as below.

1. Before installing or replacing the carbon filters, please remove the power to the unit.

2. Press the filter lock and remove the mesh filter.
   

3. Turn the carbon filter on both side of the motor anti-clockwise.
   Replace the carbon filters with the new carbon filters.

4. Place the mesh filter.

5. Connect the power supply to the wall socket.

NOTE:

• Make sure the filter is securely locked. Otherwise, it would loosen and cause danger.
• When the activated carbon filter is attached, the suction power will be lowered.

BULB REPLACEMENT

Important :

• The bulb must be replaced by a competent person.

• Always switch off the electricity supply before carrying out any operations on the appliance.
  When handling the bulb, make sure it is completely cooled down before any direct contact with the hands.

• When handling globes hold them with a cloth or gloves to ensure perspiration does not come in contact with the globe as this can reduce the life of the globe.

LED LIGHTS

• Switch the unit off and pull out the plug first.
• Wait until the light bulb is cooled down before replacement.
• Prize up the LED light carefully with the aid of a screwdriver.
• Pull out the LED light slowly and replace it with the same type and rated LED light.
• ILOCOS D code for this lamp is: DSR-1.5/65-S-64
  – LED modules –round lamp
  – Max wattage: 2X1.5 W
  – Voltage range: DC 12V
  – Dimensions:
  

Abnormity and Solution

blocking
The capacitor damaged| Replace capacitor
The motor jammed bearing damaged| Replace motor
The internal with of the motor off or a bad smell from the motor| Replace motor
Light does not work,
motor does not work| Besides the above-mentioned, check the following:
Light damaged| Replace lights
Power cord loses| Connect the wires as per the electric diagram
Oil leakage| One way valve and the air ventilation entrance are not tightly sealed| Take down the one way
valve and seal with glue
Leakage from the connection of the U-shaped section and
cover| Take the U-shaped section down and seal with soap or paint
Shake of the body| The leaf is damaged and causes shaking| Replace the leaf
The motor is not tightly hanged| Lock the motor tightly
The body is not tightly hanged| Fixed the body tightly
Insufficient suction| The distance between the body and the gas top is too long| Readjust the distance
Too much ventilation from open doors or windows| Choose a new place and resemble the machine
The machine inclines| The fixing screw is not tight enough| Tighten the hanging screw and make it horizontal
The hanging screw is not tight enough| Tighten the hanging screw and make it horizontal

ENVIRONMENTAL PROTECTION:
This product is marked with the symbol on the selective sorting of waste electronic equipment. This means that this product must not be disposed of with household waste but must be supported by a system of selective collection in accordance with Directive 2002/96/EC. It will then be recycled or dismantled to minimize impacts on the environment,  electrical and electronic products are potentially dangerous for the environment and human health due to the presence of hazardous substances.
For more information, please contact your local or regional authorities.
Note ：
a. In order to reduce the environmental impact (e.g. energy use) of the cooking process, please be sure that your product is installed according to the user manual, keep the operation place ventilated, and keep the extraction duct be direct and short as possible as it can be.
b. For the product with the manual operation mode, we suggest switching the motor off within 10 minutes after finishing the cooking process.
c. Please be sure to dismantle related components according to the user manual when maintaining for non-destructive, protect the parts to make the re- installed work can be favoring and avoid damage.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>