Nikon 05420105 NIKKOR Z 24-120mm f/4 S Lens User Guide

: June 5, 2024
: Nikon

Table of Contents

Lens Maintenance
Introduction
Using the Lens
Attachment and Removal
Technical Notes
Specifications
Notices
Documents / Resources

NIKKOR
NIKKOR Z 24-120mm f/4 S
Reference Guide

Scan for detailed operating instructions
User’s Manual

This document lists general maintenance instructions and precautions for using NIKKOR Z lenses. Topics such as lens specifications, support ed accessories, and the names and functions of lens controls are de tailed in a Reference Guide available from the Nikon Download Center. Nikon Download Cente

https://downloadcenter.nikonimglib.com/
Read this document carefully before using this product. You will also need to consult the lens Reference Guide and the documentation provided with your camera.

NIKKOR Z lenses are intended exclusively for use with mirrorless cameras featuring a Nikon Z mount.
Update the camera firmware to the latest version. With earlier versions, the camera may fail to detect the lens correctly and some features may not be available. The latest version of the camera firmware can be downloaded from the Nikon Down load Center

For your Safety
To prevent damage to property or injury to yourself or to others, read “For Your Safety” in its entirety before using this product.
After reading these safety instructions, keep them readily accessible for future refer ence

WARNING: Failure to observe the precautions marked with this icon could
res ult in death or severe injury.
CAUTION: Failure to observe the precautions marked with this icon could result in injury or property damage

WARNING

Do not disassemble or modify this product.
Do not touch internal parts that become exposed as the result of a fall or other accident.
Failure to observe these precautions could result in electric shock or another injury
Should you notice any abnormalities such as the product producing smoke, heat, or unusual odors, immediately disconnect the camera power source.
Continued operation could result in fire, burns, or another injury.
Keep dry.
Do not handle it with wet hands.
Failure to observe these precautions could result in fire or electric shock.
Do not use this product in the presence of flammable dust or gas such as propane, gasoline, or aerosols.
Failure to observe this precaution could result in an explosion or fire.
Do not directly view the sun or other bright light sources through the lens.
Failure to observe this precaution could result in visual impairment.
Keep this product out of reach of children.
Failure to observe this precaution could result in injury or product malfunction.
In addition, note that small parts constitute a choking hazard. Should a child swallow any part of this product, seek immediate medical attention:
Do not handle with bare hands in locations exposed to extremely high or low temperatures.
Failure to observe this precaution could result in burns or frostbite

CAUTION

Do not leave the lens pointed at the sun or other strong light sources.
Light focused by the lens could cause fire or damage to the product’s internal parts.
When shooting backlit subjects, keep the sun well out of the frame. Sunlight focused on the camera when the sun is close to the frame could cause a fire.
Do not leave the product where it will be exposed to extremely high temperatures, for an extended period such as in an enclosed automobile or in direct sunlight.
Failure to observe this precaution could result in fire or product malfunction.
Do not transport cameras or lenses with tripods or similar accessories attached.
Failure to observe this precaution could result in injury or product malfunction

Notices for Customers in the U.S.A.
This device complies with part 15 of the FCC Rules. Operation is subject to the follow ing two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

Federal Communications Commission (FCC) Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital devise, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not in stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.

CAUTIONS
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Nikon Corporation may void the user’s authority to operate the equipment.
Nikon Inc., 1300WaltWhitman Road,
Melville, New York 11747-3064, U.S.A.
Tel.: 631-547-4200
Notice for Customers in Canada
CAN ICES-3 B / NMB-3 B

P·recautions for Use

Do not pick up or hold the lens or camera using only the lens caps or lens hood.
Do not hold the telescoping section of extendable lenses.
Be sure to support heavy lenses (such as those with wide apertures or very long fo cal lengths) at all times while holding the camera. Failure to observe this precaution could damage the lens mount.
Keep the CPU contacts clean.
Some lenses are equipped with a rubber lens-mount gasket. If the gasket is dam aged, cease use immediately, and take the lens to the point of purchase or to a Nikon-authorized service center for repair.
Reattach the lens caps when the lens is not in use.
Slip-on lens caps (front caps) made of flexible material may crease if folded, but this does not interfere with their function.
Do not leave the lens in humid locations or in locations in which it may be exposed to moisture. Rusting of the internal mechanism can cause irreparable damage.
Do not leave the lens next to open flames or in other extremely hot locations. Extreme heat could damage or warp the lens.
Taking the lens from a warm to a cold environment or vice versa may cause dam aging condensation inside and outside the lens. Place the lens in a sealed bag or plastic case before taking it across a temperature boundary. The lens can be taken from the bag or case once it has had time to adjust to the new temperature.
We recommend that you place the lens in a lens case or trunk to protect it from scratches during transport.
Do not sit or stand on lens trunk cases supplied with very long focal length lenses or the like; such acts are dangerous.
Nikon will not be held liable in the event that lenses equipped with a security slot are stolen or damaged while a third-party anti-theft cable is attached.

Using Polyester Lens Cases
Note the following when using polyester lens cases (the CL-Cl, CL-C2, CL-C3, and CL-C4):

The case is intended to protect the lens from scratches, not from falls or other physical shocks.
The material used in the case may fade, bleed, stretch, shrink, or change color when rubbed or wet.
Be careful that the lens does not fall from the case during transport.

Lens Maintenance

Glass Elements
How you care for glass lens elements depends on whether they are fluorine- coated.·

Fluorine-coated elements:
– A simple dusting is usually sufficient.
– Smudges, fingerprints, and other oily stains can be removed using a soft, clean cotton cloth or third-party lens cleaning tissue; clean from the center outwards using a circular motion.
– To remove stubborn stains, wipe gently using a soft cloth lightly dampened with a small amount of distilled water, ethanol, or third-party lens cleaner.
– Any drop-shaped marks left from this process on the water- and oil-repellent surface can subsequently be removed with a dry cloth.
Elements without a fluorine coat:
– A simple dusting is usually sufficient.
– Smudges, fingerprints, and other oily stains can be removed using a soft, clean cotton cloth or third-party lens cleaning tissue lightly dampened with a small amount of ethanol or third-party lens cleaner; clean from the center outwards in a circular motion. Be sure to clean evenly and thoroughly without leaving smears.
Fluorine-coated elements are identified by the “fluorine-coated” label under “Lens construction” in the “Specifications” section of the lens Reference Guide.

General Maintenance

Never use organic solvents such as paint thinner or benzene to clean the lens.
Neutral Color (NC) filters (available separately) and the like can be used to protect the front lens element. Remove the lens hood before attaching or removing filters.
Do not store with naphtha or camphor moth balls or in direct sunlight. If the lens will not be used for an extended period, store it in a cool, dry location to prevent mold and rust.
Out of concern for the environment, Nikon is working to reduce its use of paper.
Read this document thoroughly before using the product.
To ensure proper use of the product, be sure to read “For Your Safety” (page 4).
After reading this document, keep it readily accessible for future reference.

Introduction

Before You Begin
Before using this product, please read these instructions carefully. You will also need to consult the documentation provided with the camera.

This lens is intended exclusively for use with mirrorless cameras featuring a Nikon Z mount.
Update the camera firmware to the latest version. With earlier versions, the camera may fail to detect the lens correctly and some features may not be available. The latest version of the camera firmware can be downloaded from the Nikon Download Center at the URL below. https://downloadcenter.nikonimglib.com/

No reproduction in any form of this document, in whole or in part (except for brief quotations in critical articles or reviews), may be made without written authorization from NIKON CORPORATION.

For Your Safety
To prevent damage to property or injury to yourself or to others, read “For Your Safety” in its entirety before using this product.
After reading these safety instructions, keep them readily accessible for future reference.

WARNING: Failure to observe the precautions marked with this icon could result in death or severe injury.
CAUTION: Failure to observe the precautions marked with this icon could result in injury or property damage.

WARNING

Do not disassemble or modify this product. Do not touch internal parts that become exposed as the result of a fall or other accident.

Failure to observe these precautions could result in electric shock or another injury.

Should you notice any abnormalities such as the product producing smoke, heat, or unusual odors, immediately disconnect the camera power source.

Continued operation could result in fire, burns, or another injury.

WARNING

Keep dry. Do not handle it with wet hands.
Failure to observe these precautions could result in fire or electric shock.
Do not use this product in the presence of flammable dust or gas such as propane, gasoline, or aerosols.
Failure to observe this precaution could result in an explosion or fire.
Do not directly view the sun or other bright light sources through the lens.
Failure to observe this precaution could result in visual impairment.
Keep this product out of reach of children.
Failure to observe this precaution could result in injury or product malfunction. In addition, note that small parts constitute a choking hazard. Should a child swallow any part of this product, seek immediate medical attention.
Do not handle with bare hands in locations exposed to extremely high or low temperatures.
Failure to observe this precaution could result in burns or frostbite.

CAUTION

Do not leave the lens pointed at the sun or other strong light sources. Light focused by the lens could cause fire or damage to the product’s internal parts. When shooting backlit subjects, keep the sun well out of the frame. Sunlight focused on the camera when the sun is close to the frame could cause a fire.
Do not leave the product where it will be exposed to extremely high temperatures, for an extended period such as in an enclosed automobile or in direct sunlight.
Failure to observe this precaution could result in fire or product malfunction.
Do not transport cameras or lenses with tripods or similar accessories attached.
Failure to observe this precaution could result in injury or product malfunction.

Using the Lens

Parts of the Lens: Names and Functions
The parts of the lens are listed below.

Lens hood mounting mark
Use when attaching the lens hood.
“Attaching and Removing the Lens Hood” (p.16)
Focus ring
Use for manual focus.
• When focusing using autofocus, you can adjust the focus manually by rotating the ring while the shutter-release button is pressed halfway; after focusing, press the shutter-release button the rest of the way down to shoot.
Zoom ring
Rotate the ring to zoom in or out.
Focal length scale
Determine the approximate focal length when zooming the lens in or out.
Focal length mark
Determine the approximate focal length when zooming the lens in or out.
Control ring
Rotate to adjust a setting such as [Aperture] or [Exposure compensation] assigned using the camera. For more information, see the description of [ Custom control assignment], [Custom controls], or [Custom controls (shooting)] in the documentation provided with the camera.
Lens mounting mark
Use when mounting the lens on the camera.
“Attachment and Removal” (p.13)
Rubber lens-mount gasket
Helps prevent the ingress of water droplets or dust along the surfaces where the lens and camera meet when the lens is mounted on the camera.*

There is no guarantee that the gasket is completely proof against the ingress of water droplets or dust in all circumstances. 9. CPU contacts
Used to transfer data to and from the camera.
1. L-Fn button
  Press to perform a function assigned using the camera. For more information, see the description of [Custom control assignment], [Custom controls], or [Custom controls (shooting)] in the documentation provided with the camera.
2. Focus-mode switch
  Choose a focus mode.
  • A: Autofocus
  • M: Manual focus
  Note that regardless of the setting chosen, the focus must be adjusted manually when manual focus mode is selected using camera controls.
3. Lens hood
  Lens hoods block stray light that would otherwise cause flare or ghosting.
  They also serve to protect the lens.
  “Attaching and Removing the Lens Hood” (p.16)
4. Lens hood lock mark
  Use when attaching the lens hood.
  “Attaching and Removing the Lens Hood” (p.16)
5. Lens hood alignment mark
  Use when attaching the lens hood.
  “Attaching and Removing the Lens Hood” (p.16)
6. Lens cap (front cap)
7. Lens cap (rear cap)
  • The rear lens caps supplied with lens kits may differ from that shown here, in which case 1 is not required.

Attachment and Removal

Attaching the Lens

Turn the camera off, remove the body cap, and detach the rear lens cap.
Position the lens on the camera body, keeping the mounting mark on the lens aligned with the mounting mark on the camera body ( 1 ), and then rotate the lens counterclockwise ( 2 ) until it clicks into place.

Removing the Lens

Turn the camera off.
Press and hold the lens release button ( 1 ) while turning the lens clockwise ( 2).

Attaching and Removing the Lens Hood

Align the lens hood mounting mark with the lens hood alignment mark ( 1 ) and then rotate the lens hood ( 2 ) until the mounting mark is aligned with the lens hood lock mark ( 3 ).

1 Lens hood alignment mark
2 Lens hood mounting mark
3 Lens hood lock mark

Gripping the front too tightly makes the lens hood difficult to attach or remove.
When rotating the lens hood, hold it near the lens hood alignment mark ( ).
To remove the lens hood, reverse the above steps.
The lens hood can be reversed and mounted on the lens when not in use.

Precautions for Use

Do not pick up or hold the lens or camera using only the lens caps or lens hood.
Keep the CPU contacts clean.
Should the rubber lens-mount gasket be damaged, cease use immediately and take the lens to a Nikon-authorized service center for repair.
Reattach the lens caps when the lens is not in use.
Do not leave the lens in humid locations or in locations in which it may be exposed to moisture. Rusting of the internal mechanism can cause irreparable damage.
Do not leave the lens next to open flames or in other extremely hot locations.
Extreme heat could damage or warp the lens.
Taking the lens from a warm to a cold environment or vice versa may cause damaging condensation inside and outside the lens. Place the lens in a sealed bag or plastic case before taking it across a temperature boundary. The lens can be taken from the bag or case once it has had time to adjust to the new temperature.
We recommend that you place the lens in its case to protect it from scratches during transport.

Lens Maintenance

Removing dust is normally sufficient to clean the glass surfaces of the lens.
When cleaning the fluorine-coated front lens element:
– Smudges, fingerprints, and other oily stains can be removed using a soft, clean cotton cloth or third-party lens cleaning tissue; clean from the center outwards using a circular motion.
– To remove stubborn stains, wipe gently using a soft cloth lightly dampened with a small amount of distilled water, ethanol, or third-party lens cleaner.
– Drop-shaped marks may form on fluorine-coated surfaces, which are highly water- and oil-repellent. Such marks can be removed with a dry cloth.
When cleaning the rear lens element, which is not fluorine-coated:
– Smudges, fingerprints, and other oily stains can be removed using a soft, clean cotton cloth or third-party lens cleaning tissue lightly dampened with a small amount of ethanol or third-party lens cleaner; clean from the center outwards in a circular motion. Be sure to clean evenly and thoroughly without leaving smears.
Never use organic solvents such as paint thinner or benzene to clean the lens.
Neutral Color (NC) filters (available separately) and the like can be used to protect the front lens element.
Do not store the lens in direct sunlight or with naphtha or camphor moth balls. If the lens will not be used for an extended period, store it in a cool, dry location to prevent mold and rust.

Technical Notes

Cameras with AF-Assist Illuminators
The lens or lens hood may block the light from the camera AF-assist illuminator.

For information on using the lens with cameras that have built-in AF-assist illuminators, visit the site below. https://downloadcenter.nikonimglib.com/

Using the Lens on Cameras with a Built-in Flash
Shadows will be visible in photos where light from the built-in flash is obscured by the lens or lens hood. Remove the lens hood before shooting. Note, however, that depending on the distance to the subject, and in the case of zoom lenses also on the lens focal length, shadows may appear even when the lens hood is removed.

For the information on focal lengths and subject distances at which shadows will not appear in photos taken with a built-in flash, visit the site below. https://downloadcenter.nikonimglib.com/

Accessories
Supplied Accessories

LC-77B Lens Cap (front cap)
LF-N1 Lens Cap (rear cap)*
HB-102 Lens Hood
CL-C2 Lens Case
Different rear caps may be supplied with lens kits.

Using the Lens Case

The case is intended to protect the lens from scratches, not from falls or other physical shocks.
The case is not water resistant.
The material used in the case may fade, bleed, stretch, shrink, or change color when rubbed or wet.
Remove dust with a soft brush.
Water and stains can be removed from the surface with a soft, dry cloth. Do not use alcohol, benzene, thinner, or other volatile chemicals.
Do not store in locations exposed to direct sunlight or too high temperatures or humidity.
Do not use the case to clean the monitor or lens elements.
Be careful that the lens does not fall from the case during transport.
Material: Polyester

Other Compatible Accessories
77 mm filters
Filters

Use only one filter at a time.
Remove the lens hood before attaching filters. You will also need to remove the lens hood before rotating circular polarizing filters.

Specifications

Mount	Nikon Z mount
Focal length	24 – 120 mm
Maximum aperture	f/4
**** Lens construction	16 elements in 13 groups (including 3 ED elements, 1

aspherical ED element, 3 aspherical elements, elements with Nano Crystal and ARNEO coats, and a fluorine-coated front lens element)
Angle of view| FX format: 84° – 20°20′
DX-format: 61° – 13°20′
Focal length scale| Graduated in millimeters (24, 28, 35, 50, 70, 85, 120)
Focusing system| Internal focusing system
Minimum focus distance (measured from the focal plane)| 0.35 m (1.15 ft) at all zoom positions
Maximum reproduction ratio| 0.39×
Diaphragm blades| 9 (rounded diaphragm opening)
Aperture range| f/4 – 22
Filter-attachment size| 77 mm (P = 0.75 mm）
Dimensions (maximum diameter × distance to end of the lens from camera lens mount flange)| Approx. 84 mm × 118 mm (3.4 in. × 4.7 in.)
---|---
Weight| Approx. 630 g (1 lb 6.3 oz)

Nikon reserves the right to change the appearance, specifications, and performance of this product at any time and without prior notice.

Notices

Notices for Customers in the U.S.A.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Federal Communications Commission (FCC) Radio
Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.

CAUTIONS
●Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Nikon Corporation may void the user’s authority to operate the equipment.
Nikon Inc., 1300 Walt Whitman Road, Melville, New York 11747-3064, U.S.A.
Tel.: 631-547-4200
Notices for Customers in Canada
CAN ICES-3 B / NMB-3 B
Notices for Customers in Europe
This symbol indicates that electrical and electronic equipment is to be collected separately.
The following applies only to users in European countries:

This product is designated for a separate collection at an appropriate collection point. Do not dispose of as household waste.
Separate collection and recycling helps conserve natural resources and prevent negative consequences for human health and the environment that might result from incorrect disposal.
For more information, contact the retailer or the local authorities in charge of waste management.

Nikon

Serial No
| Model
Z 24-120/4 S
---|---

ONE-YEAR LIMITED WARRANTY

THIS IS YOUR NIKON INC. (VALID IN THE CONTINENTAL UNITED STATES AND HAWAII, PUERTO RICO, AND U.S. VIRGIN ISLANDS), NIKON CANADA INC.
(VALID IN ALL CANADIAN PROVINCES AND TERRITORIES) OR NIKON MEXICO, S.A. DE C.V. (VALID IN ALL MEXICAN STATES) (EACH INDIVIDUALLY;
AS THE CASE MAY BE, “NIKON”) ONE-YEAR LIMITED WARRANTY FOR NEW NIKON CAMERAS, LENSES, speedlights, AND ANY NIKON HARDWARE
ITEMS INCLUDED IN THE ACTUAL PRODUCT BOX WITH ANY OF THE FOREGOING (EACH, A “PRODUCT”). YOU MUST PRESENT THIS WARRANTY
FORM TOGETHER WITH YOUR PURCHASE RECEIPT THAT DISPLAYS THE PURCHASE DATE TO OBTAIN WARRANTY SERVICE._

This Product is warranted by Nikon to be free from defects in material and workmanship for one (1) year from the date of purchase by the original consumer purchaser. During this one-year period, if this Product is found to be defective in material or workmanship, Nikon will at its option, either repair or replace this product with a product of comparable specifications and value, each without charge, or refund the purchase price shown on your purchase receipt. Except to the extent restricted or prohibited by law, this warranty is subject to the following conditions, limitations, and exclusions:

This warranty extends to the original consumer purchaser only and is not assignable or transferable unless otherwise required by law. “”
This warranty shall not apply to any Product which has been subjected to misuse, abuse, abnormal use, negligence, alteration, accident, or power surge if the Product contains electronic components or has had its serial number altered or removed.
This warranty does not apply to any defects or damage directly or indirectly caused by or resulting from the use of unauthorized replacement parts and/or services performed by unauthorized personnel.
This warranty does not apply to any batteries.
This warranty is valid only with authentic Products, sold new by Nikon and purchased from Nikon or its authorized dealers/resellers In the country of purchase.
This warranty does not apply to non-Nikon products provided by Nikon, which are instead covered under the warranty, if any, issued by their respective manufacturers.

SUBJECT TO APPLICABLE LAW TO THE CONTRARY, THIS WARRANTY 1,$ MADE EXPRESSLY IN LIEU OF ALL OTHER REPRESENT, ATIONS, WARRANTIES, AND CONDITIONS, EXPRESS, IMPLIED, STATUTORY OR COLLATERAL, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE QR NONINFRINGEMENT, QUALITY OR DURABILITY, AND ALL OTHER OBLIGATIONS ON THE PART OF NIKON PROVIDED, HOWEVER, THAT If THE DISCLAIMER OF IMPLIED WARRANTIES AND CONDITIONS IS INEFFECTIVE UNDER APPLICABLE LAW, THE DURATION OF ANY IMPLIED WARRANTIES ARISING BY OPERATION OF LAW SHALL BE LIMITED TO ONE YEAR FROM THE DATE OF PURCHASE OR SUCH LONGER PERIOD AS MAY BE REQUIRED BY APPLICABLE LAW. SUBJECT TO APPLICABLE LAW TO THE CONTRARY, NIKON HEREBY DISCLAIMS ANY AND All LIABILITY FOR CONSEQUENTIAL. INCIDENTAL, SPECIAL, INDIRECT, EXEMPLARY, OR PUNITIVE DAMAGES ARISING OUT OF OR IN CONNECTION WITH ANY BREACH OF THIS WARRANTY OR ANY OTHER CLAIM
WITH RESPECT TO THIS PRODUCT, INCLUDING BUT NOT LIMITED TO, CLAIMS OF NEGLIGENCE, STRICT LIABILITY IN TORT, OR BREACH OF CONTRACT.
SOME STATES/PROVINCES/TERRITORIES DO NOT ALLOW (A) LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR (B) THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS
WARRANTY APPLIES TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, AND UNLESS RESTRICTED OR prohibited BY LAW. WHERE ANY
THE TERM OF THIS WARRANTY IS RESTRICTED OR PROHIBITED BY APPLICABLE LAW, SUCH TERM SHALL BE NULL AND VOID, BUT THE REMAINDER OF THIS WARRANTY SHALL REMAIN IN EFFECT. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAVE!: OTHER RIGHTS WHICH VARY FROM STATE/PROVINCE/TERRITORY TO STATE/PROVINCE/TERRITORY.
UNLESS RESTRICTED OR PROHIBITED BY APPLICABLE LAW, THIS WARRANTY is VALID ONLY IN THE COUNTRY WHERE THE ORIGINAL CONSUMER PURCHASER PURCHASED THE PRODUCT FROM NIKON OR ITS AUTHORIZED DEALERS/RESELLERS IN THAT COUNTRY.

To obtain performance of the warranty obligations in the country of purchase, the original consumer purchaser must return this Nikon Product together with this warranty form and invoice or purchase receipt displaying the purchase date to the appropriate Nikon service facility. A Nikon authorized dealer stamp may also be accepted as proof of purchase for Mexico. The current address of Nikon’s service facility within the United States can be obtained by visiting www.nikonusa/support or by calling 1-800-645-6687; within Canada: www.nikon.ca/support or by calling 1-877-534-991 O; within Mexico: www.nikon.com.mx/soporte or by calling 001-800-645-6687. Unless restricted or prohibited by applicable law, in returning this Nikon Product for repair or replacement, or refund under this warranty, the original consumer purchaser must prepay all postage, shipping transportation, insurance, and delivery costs, and the Nikon Product must be delivered in either its original carton or a similar package affording an equal degree of protection. Nikon will not be responsible for any loss or damage incurred in connection with the return of this Nikon Product.
Nikon Canada Inc. has its principal business address at 1366 Aerowood Drive, Mississauga, ON L4W 1 Cl, Canada.
Nikon Inc. has its principal business address at 1300 Walt Whitman Road, Melville, NY 11747, United States of America.
Nikon Mexico, S.A de C.V. has its principal business address at Av. Paseo de la Reforma No. 250, Torre Niza, Piso 12, Colonia Juarez, Alcaldfa Cuauhtemoc, C. P. 06600, Ciudad de Mexico. Notice for residents of the country of Mexico: Nikon product accessories and other equipment can be found on Nikon Mexico, S.A de C.V. website at www.nikon.com.mx and its authorized dealers.
THIS WARRANTY FORM MAY NOT BE REPRODUCED OR COPIED AND WILL BE VALID ONLY WITH AUTHENTIC NIKON PRODUCTS.

NIKON CORPORATION
© 2021 Nikon Corporation **SB1I01(11)
7MMA7411-01**