Tengtek T215A Industrial All In One PC Instruction Manual
- June 5, 2024
- Tengtek
Table of Contents
Tengtek T215A Industrial All In One PC
Product Description
This product is a customized industrial touch all-in-one pc.The front frame is made of 6mmaluminum alloy to prevent corrosion, the back shell is made of sheet metal, the heat dissipation plate is made of high-performance aluminum alloy, and the machine is made of UV resistant paint process. The machine adopts AG anti-glare glass, full fitting process, full Angle of view, wide temperature LCD screen, with high performance and low power consumption processor, it has high performance， excellent display effect, and excellent heat dissipation performance brings longer service life The waterproof rating of the front panel is IP65, suitable for outdoor and semi-outdoor applications. The rich interface design, excellent display effect and solid design of the machine make it easy to cope with the harsh environment of the project application.
Operating environment
- In order to prevent dirt, dust attached to the machine affect the display and toucheffect, the installation point should be far away from the dusty environment. 2. In order to prevent water mist, water droplets splashing in the machine, and resultingin damage to internal parts, the installation place should avoid damp environment.
- Try to avoid direct sunlight, can prolong the service life of the machine.
- It is recommended that the installation place of the whole machine be in a ventilatedposition, and a space of 10cm to 20cm should be set aside around the touch all-in-one machine to maintain good ventilation;Operating temperature must be between -10℃and 60℃.
- Please ensure that the ground wire (E pole) of the power plug bar is properly grounded when installing the machine.
- Please make sure not to shake the machine strongly when installing the whole machine.
Operation instructions
- The machine has M4 VESA mounting holes and mounting screws on the back. During installation, please handle with care and ensure that all screws are tightened to avoid accidental scratches or damage caused by falling off the machine.
- The machine is equipped with an appropriate power adapter. Ensure that the voltage ranges from 100V to 240V during installation, and tighten the aviation power interface at the equipment end to maintain a good power supply environment.
- The bottom of the machine is equipped with a power switch. After confirming the power connection, it is necessary to turn on the switch before using the machine. TheLED light on the switch is on for the normal power-on state of the machine. Disconnect the power supply when the machine is not in use.
- It is necessary to prevent rainwater or liquid from entering the interface at the bottom of the machine so as not to cause short circuit damage to the machine.
- There is a brightness sensor in the upper left corner of the screen, which automatically adjusts the brightness of the screen according to the brightness of the environment. Manual adjustment is not required.
- The machine supports 10-point touch and no driver installation is required.
- It is recommended not to use in thunderstorm weather, so as not to damage the machine.
Safety precautions
Power cord and socket
- Do not overload ac power sockets and extended wires, because overloading may cause fire or electric shock.
- The power cord should be properly set to avoid being trampled or squeezed by objects.
- Check the plug and power cable interface of the device. Remove the power plug before moving the device to avoid damage to the AC power cable, resulting in fire or electric shock.
- Fully insert the AC power plug into the AC power socket. The loose plug may cause sparks and fire.
- When pulling out the AC power cable, hold the plug and do not pull the power cable.
- Do not leave the machine in a standby state when it is not used for a long time. Please pull out the plug from the power socket.
- Use the power supply specified on the product label. The three-core power supply must be properly connected to the earth to avoid electric shock.
- Caution should be exercised for emergency power sources that are generated by generators after power failure. Ensure that the voltage remains stable before they can be used. Generally speaking, the voltage in the range of 100V-240V, as long as the voltage continues to be stable, not high or low, the machine can be used normally.
Installation and use
- All interfaces of the machine should be plugged and unplugged in case of power failure. Do not remove the back cover without authorization to avoid electric shock. Thereare no parts inside the machine that users can handle by yourself. If there is any problem, please contact the customer service center of the machine manufacturer
- Do not use the unit near water, such as bathtubs, swimming pools or damp basements. Do not put water containers (vases, cups, cosmetic cases) on the machine
- Do not place the unit in sunlight or near heat sources, such as radiators, heating equipment, stoves and other heating equipment. The machine is suitable for use in the environment with relatively no electromagnetic interference. If the machine is used near a strong electromagnetic field or where the electromagnetic noise covers the input signal, the picture or sound will fluctuate or produce noise and other interference phenomena.
- Do not let metal or combustible objects fall into the machine, especially when children are present. If an exception occurs, do as follows: 1. Turn off the power immediately. 2. Remove the power plug from the AC power socket
Clean
- Before cleaning the unit, remove the power plug from the AC power socket; otherwise, electric shock may occur. Please wipe the housing with a soft dry cloth. Do not spray volatile compounds on the housing
- Please use neutral detergent dissolved in water to wipe and avoid touching the LCD screen if the case is dirty
- Do not use thinner, gasoline, alcohol and other organic solvents to wipe the machine; When wiping the LCD screen, be sure to use a special LIQUID crystal cleaning cloth, or avery soft cotton flannelette, spray a proper amount of non-ionic water, so that the cleaning cloth slightly damp, and then gently wipe; LCD screen is very “delicate”, must be wiped gently, in case of broken screen.
Move the machine
The machine must be moved by two or more people. When moving, do not shakeor
shake the whole machine too much. The whole machine may fall and damage or
cause personal injury.
Note
This device complies with Part 1 5 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device is verified Io comply with Part of the FCC Rules for use with cable television service.
This equipment has been tested and found to comply with the limits for a Class
B digital
the device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radiocommunications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment. The device has been evaluated to meet general RF exposure requirements. To maintain compliance with FCC’s RF exposure guidelines, the distance must be at least 20cmbetween the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antenna(s).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>