VISUAL COMFORT S5170 Menil Tall Chandelier Instruction Manual

: June 5, 2024
: VISUAL COMFORT

Table of Contents

ASSEMBLY INSTRUCTIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Instruction Manual

ASSEMBLY INSTRUCTIONS

Option 1: Canopy Mounted Drive

Menil Tall Chandelier
Item # S5170
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect items and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

Phillips Screwdriver
Slip Joint Pliers
Wire Strippers| Slotted Screwdriver
Measuring Tape| Chain Pliers
Wire Cutter
---|---|---

Carefully remove all parts from the box. Place on a clean, soft surface.
Determine desired overall length, and amount of chain (F) needed. Shorten chain (F) using chain pliers (Keep extra chain).
Install mounting plate (B) to the junction box and secure with mounting screws (C).
Add collar ring (E) , canopy (D), and driver housing (L) to chain (F) and slip down carefully.
Thread collar loop (R) to mounting plate (B) and secure using set screw (S) with a provided wrench (T).
Install driver housing (L) and canopy (D) to mounting plate (B) and secure with collar ring (E).
Attach chains (H) to hooks (M) on fixture body (I).
Thread fixture wire and ground wire through the chain (F).
NOTE: When you reach the collar loop, ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.
Separate two sides of the molded wire, and strip insulation on each 5/8″.
Loosen collar ring (E) and let driver housing (L) and canopy (D) slip down the chain (F) carefully.
Twist all fixture wires together and slip through the center hole of the collar loop (R).
NOTE: Untwist wires and separate to prepare for connection
Option 1: Canopy Mounted Driver****
Connect fixture neutral wire (ribbed) to the driver output neutral wire (black) using wire nut (A).
Connect fixture hot wire (smooth with markings) to the driver output hot wire (red) using wire nut (A).
Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 1). Tighten.
NOTE: It is imperative that the fixture is grounded.
Connect driver input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
Connect the driver input hot wire (black) to the supply hot wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
Make sure all wire connections are tight, then carefully tuck them into the junction box.
Insert driver (N) into the mounting plate bracket.
Install driver housing (L) and canopy (D) to mounting plate (B) and secure with collar ring (E).
To install glass rods (J) insert into hole on the bottom of fixture frame, align with groove in rod and slide over.
Once all glass rods (J) are installed, align the glass rod (K) with a hole on the bottom of the fixture frame and thread to secure it. (see diagram 2)
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Option 2: Ceiling Mounted Driver

Phillips Screwdriver
Slip Joint Pliers
Wire Strippers| Slotted Screwdriver
Measuring Tape| Chain Pliers
Wire Cutter
---|---|---

Carefully remove all parts from the box. Place on a clean, soft surface.
Place driver (N) into the ceiling and route all wires through one of the knockouts in the junction box.
Locate a shorter profile mounting plate (O) for option 2 mounting. Install shorter plate (O) to the junction box and secure with mounting screws (C).
Determine desired overall length, and amount of chain (F) needed. Shorten chain (F) using chain pliers (Keep extra chain).
Add collar ring (E) and canopy (D) to chain (F) and slip down carefully.
Thread collar loop (R) to shorter mounting plate (O) and secure using set screw (S) with a provided wrench (T).
Install canopy (D) to mounting plate (B) and secure with collar ring (E).
Attach chains (H) to hooks (M) on fixture body (I).
Thread fixture wire and ground wire through the chain (F).
NOTE: When you reach the collar loop, ensure there is no tension on the wires. Cut excess wires, being sure to leave about 12” to reach the junction box.
Separate two sides of the molded wire, and strip insulation on each 5/8″.
Loosen collar ring (E) and let canopy (D) slip down the chain (F) carefully.
Twist all fixture wires together. Slip through the center hole of the collar loop (R).
NOTE: Untwist wires and separate to prepare for connection.
Connect fixture neutral wire (ribbed) to the driver output neutral wire (black) using wire nut (A).
Connect fixture hot wire (smooth with markings) to the driver output hot wire (red) using wire nut (A).
Connect supply ground wire (usually green or bare copper) around the green grounding screw. Tighten.
NOTE: It is imperative that the fixture is grounded
Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 1). Tighten.
NOTE: It is imperative that the fixture is grounded.
Connect driver input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
Connect the driver input hot wire (black) to the supply hot wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
Make sure all wire connections are tight, then carefully tuck them into the junction box.
Install canopy (D) to short mounting plate (O) and secure with collar ring (E).
To install glass rods (J) insert into hole on the bottom of fixture frame, align with groove in rod and slide over.
Once all glass rods (J) are installed, align the glass rod (K) with a hole on the bottom of the fixture frame and thread to secure it. (see diagram 2)